• 한국재료학회지
• /
• 제29권11호
• /
• pp.657-663
• /
• 2019

In this work, we study physical and mechanical properties of oxide films formed on AZ91D magnesium alloy by plasma anodization at different temperatures. It is found that the higher the electrolyte temperature, the lower is the breakdown voltage of oxide layer. This is probably because films formed at higher temperatures are thinner and denser. Moreover, electrolyte temperature plays an important role in the physical properties of the films. As the electrolyte temperature increases from 20 to $50^{\circ}C$, the hardness of the oxide layer increases. Friction test against steel balls indicates that wear scars become narrower for films formed at higher temperatures because the films are harder, as indicated by the Vickers hardness. The thinner and denser nature of the oxide film formed at $50^{\circ}C$ is also advantageous for heat transfer when film is used as a heat sink. Laser flash test results show very fast heat transfer for AZ91D with plasma anodized oxide layer formed at higher temperatures.

• 대한금속재료학회지
• /
• 제49권8호
• /
• pp.601-607
• /
• 2011

The study investigated the influence of current density on the corrosion-protection properties of an AZ91 Mg alloy subjected to plasma electrolytic oxidation coating. The present coatings were carried out under an AC condition at three different current densities, i.e., 100, 150, and $200mA/cm^2$. From microstructural observations, the micro cracks connecting each micro pore were pronounced on the oxide surface of the samples coated at current densities higher than $150mA/cm^2$ since increasing the current density in this study led to an increment in the relative volume fraction of the MgO compound. Based on potentio dynamic polarization and immersion tests, the sample coated at a current density of $100mA/cm^2$ showed superior corrosion resistance.

• 한국표면공학회지
• /
• 제30권6호
• /
• pp.365-373
• /
• 1997

316L and 420 Stainless steels were deposited onto AZ9ID commercial magnesium alloy by plasma spray process with various gas flow rate of, TEX>$H_2$ secondary gas. And hardness as well as were track volume, coefficient of friction also had been measured. wear and hardness were measured by using reciprocal configuration tribometer and microghardness tester, respectively. Also, the microstructure of the coatings surface the cross sectional area of coating surface and cross sectional area of coaing/Substrate interface had been analyzed with Scanning Electron Microscope(SEM) and Optical microscope(OM). Finally, optimal process parameters for the improvement of coating efficiency such as mechanical property and wear behavior were examined.

• 한국주조공학회지
• /
• 제30권6호
• /
• pp.224-230
• /
• 2010

To prevent oxidation of Mg melt, $SF_6$ gas has been generally used for Mg alloys during melting and casting as a cover gas. The use of $SF_6$ gas, however, will be restricted owing to its crucial impact on global warming. Non-$SF_6$ process during melting and casting in diecasting industry has been proved with Eco-Mg alloys by a simple addition of small amount of CaO into Mg alloys. This paper shows non-$SF_6$ diecasting procedures for 0.7wt% CaO added AZ91D Eco-Mg alloys. Cold-chamber diecasting was performed under $CO_2$ atmosphere without $SF_6$ gas. An increment of mechanical properties, especially strength and ductility of Eco-Mg alloys is, in part, due to high-quality melt, refined grain size and $Al_2Ca$ second phase strengthening. Microstructures and mechanical properties of 0.7wt% CaO added AZ91D Eco-Mg alloys are evaluated in comparison with those of conventional AZ91D Mg alloy.

• 한국진공학회지
• /
• 제16권1호
• /
• pp.23-26
• /
• 2007

AZ91D의 마그네슘합금을 열처리별 온도에 따라서 광반사 및 전자현미경 측정을 하였다. 광반사 측정 결과 열처리 한 시료에서 carbon defect에 대한존재를 확인하였으며, 전자현미경 측정을 통하여 열처리 후에 산화막이 더 균일하게 성장되는 것을 확인하였다.

• 마이크로전자및패키징학회지
• /
• 제17권3호
• /
• pp.71-77
• /
• 2010

마그네슘 합금은 낮은 밀도를 가지는 장점을 이용하여 자동차, 항공, 이동전화, 컴퓨터 등에 많이 쓰이고 있으나 기계적 강도가 낮고 내부식성이 좋지 않아 사용이 제한되었다. 마그네슘 합금 표면에 내식성 산화층을 형성하기 위하여 환경 친화적인 전해 플라즈마 산화법(PEO)을 연구에 사용하였다, PEO법은 수용약 중에서 플라즈마를 발생시켜 전기화학적 산화막을 형성시키는 방법이다. 인가전압과 전휴가 산화피마에 미치는 영향에 대하여 고찰하였다, 또한, 직류와 펄스전류를 사용하여 결과를 분석하였다. 펄스전류를 사용하고 정전류법을 사용한 경우에 치밀한 산화막을 얻을 수 있었다, 부식특성 분석을 위하여 양극산화분극방법을 이용하였다. 표면의 강도는 처리전의 AZ9ID에 비하여 5배 이상 증가하였다.

• 한국재료학회지
• /
• 제29권5호
• /
• pp.288-296
• /
• 2019

The passivation of AZ91D Mg alloys through plasma anodization depends on several process parameters, such as power mode and electrolyte composition. In this work, we study the dependence of the thickness, composition, pore formation, surface roughness, and corrosion resistance of formed films on the electrolyte temperature at which anodization is performed. The higher the electrolyte temperature, the lower is the surface roughness, the smaller is the oxide thickness, and the better is the corrosion resistance. More specifically, as the electrolyte temperature increases from 10 to $50^{\circ}C$, the surface roughness (Ra) decreases from 0.7 to $0.15{\mu}m$ and the corrosion resistance increases from 3.5 to 9 in terms of rating number in a salt spray test. The temperature increase from 10 to $50^{\circ}C$ also causes an increase in magnesium content in the film from 25 to 63 wt% and a decrease in oxygen from 66 to 21 wt%, indicating dehydration of the film.

• 열처리공학회지
• /
• 제37권2호
• /
• pp.66-72
• /
• 2024

To investigate the effect of deformation condition on microstructure and texture formation behaviors of AZ91 magnesium alloy with three kinds of initial texure during high-temperature deformation, plane strain compression tests were carried out at high-temperature deformation conditions - temperature of 673 K~723 K, strain rate of 5 × 10^-3s^-1, up to a strain of -1.0. To clarify the texture formation behavior and crystal orientaion distribution, X-ray diffraction and EBSD measurement were conducted on mid-plane section of the specimens after electroltytic polishing. As a result of this study, it is found that the main component and the accumulation of pole density vary depending on initial texture and deformation caondition, and the formation and development basal texture components ({0001} <$10\bar{1}0$>) were observed regardless of the initial texure in all case of specimens.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2012년도 추계총회 및 학술대회 논문집
• /
• pp.19-19
• /
• 2012

마그네슘 합금은 낮은 비중의 경량화 금속 소재이며, 주로 주조 주조재 형태로 상당한 기간 활용되어 왔으며, 최근에는 포스코에서 AZ31 합금으로 판재를 생산하면서 판재상의 마그네슘 소재의 응용이 본격화되고 있다. 포스코에서 판재로 생산되는 합금은 AZ31합금이 주종이며, AZ61 합금의 경우도 일부 생산되고 있으며, 향후 다양한 합금의 판재의 개발이 진행될 예정이다. 마그네슘 합금은 화학적 활성이 커서 내식성 확보를 위한 표면처리가 필수적이며, 내식성의 확보가 상업적 적용을 위하여 필수적이다. 기존의 마그네슘 합금의 표면처리 방법은 주로 AZ91D의 다이캐스팅재에 집중되어 왔으며, 포스코에서 생산되는 AZ31의 스트립 캐스팅재의 표면처리는 합금의 차이로 인하여 새롭게 공정이 개발되어야 한다. 본 발표에서는 AZ31 판재를 이용한 표면처리에서 전처리 공정이 미치는 영향에 대하여 논하고자 한다.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2007년 추계학술발표대회 개요집
• /
• pp.144-145
• /
• 2007

Magnesium alloys are the lightest in commercial alloys. Also, they have high damping capacity and the shielding effect of electromagnetic waves. Recently, magnesium alloys have received considerable attention from the transportation industry. Many manufacturers of cars try to increase the use of magnesium alloys in their product. In order to evaluate the weldability of magnesium alloy, gas-tungsten arc welding(GTAW) have been applied to the AZ31, AZ61 and AZ91 alloys and established the optimum welding conditions.