• Applied Microscopy
• /
• 제44권2호
• /
• pp.79-82
• /
• 2014

Aluminum nitride (AlN) powder was easily synthesized by the direct nitridation of Al melt containing ~20 wt.% Mg catalyst and the nitriding behavior was investigated by thermodynamic calculation and through observations of electron microscopy and X-ray diffraction. The addition of Mg catalyst decreased the nitriding temperature below $1,000^{\circ}C$, which is comparable to the high nitriding temperature of $1,400^{\circ}C$ required in carbothermal method. It was caused by a significant increase of the solubility of nitrogen gas due to the increase of Mg catalyst in Al melt. The dissolved nitrogen gas met Mg catalyst and was transformed into metastable $Mg_3N_2$. Finally the metastable phase reacted with Al to AlN.

• Applied Microscopy
• /
• 제44권2호
• /
• pp.68-73
• /
• 2014

With wide use of nano-materials, it is increasingly important to address their potential toxicity to mammalian cells. However, toxic effects of these materials have been mainly assessed by the cell survival assays. Considering that mitochondrial morphology and quality are highly sensitive to the condition of the cells, and the impairment of mitochondrial function greatly affect the survival of cells, here we tested the impact of multi-walled carbon nanotubes (MWNT) on the survival, mitochondrial morphology, and their membrane potential in HeLa cells. Interestingly, although MWNT did not induce cell death until 24 hours as assessed by pyknotic cell assay, mitochondrial length was elongated and the mitochondrial membrane potential was significantly reduced by exposure of HeLa cells to MWNT. These results suggest that MWNT exposure is potentially harmful to the cell, and the mechanism how MWNT alters mitochondrial quality should be further explored to assess the safety of MWNT use.

• Applied Microscopy
• /
• 제47권1호
• /
• pp.55-62
• /
• 2017

This paper describes experiments aimed at characterizing the behavior of field electron emitters fabricated by coating carbon fibers with epoxylite resin. Polyacrylonitrile carbon fibers of type VPR-19, thermally treated at $2,800^{\circ}C$, were used. Each was initially prepared in a "uncoated" state, by standard electro polishing and cleaning techniques, and was then examined in a scanning electron microscope. The fiber was then baked overnight in a field electron microscope (FEM) vacuum chamber. Current-voltage characteristics and FEM images were recorded on the following day or later. The fiber was then removed from the FEM, coated with resin, "cured" by baking, and replaced in the FEM. After another overnight bake, the FEM characterization measurements were repeated. The coated fibers had significantly better performance than uncoated fibers. This confirms the results of earlier experiments, and is thought to be due in part to the formation of a conducting channel in the resin over layer. For the coated fiber, lower voltages were needed to obtain the same emission current. The coated fibers have current-voltage characteristics that show smoother trends, with greater stability and repeatability. No switch-on phenomena were observed. In addition, the emission images on the phosphor-coated FEM screen were more concentrated, and hence brighter.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2011년도 추계학술발표대회
• /
• pp.11.1-11.1
• /
• 2011

세계 최초의 전자종이가 등장한 때는 1975년 미국 제록스(Xerox)에서 개발된 '자이리콘(Gyricon)'이었으나, 2005년 상업성의 이유로 개발이 중단됐다. 2004년 소니(Sony)도 '리브리에(Librie)'라는 전자책 단말기를 출시했으나 콘텐츠 부족으로 판매가 워낙 부진해 시장에서 철수하였다. 그러나 2007년 인터넷 서점 아마존에서 베스트셀러를 포함한 8만 종 이상의 컨텐츠를 기반으로 전자책 '킨들(Kindle)'을 선보여 대 성공을 하였다. 2009년에만 540만대, 2010년에는 800만대 이상 팔리는 대히트를 기록한 것이다. 이러한 전자책의 성공의 이유는 다음과 같이 생각된다. 전자종이의 첫 번째 장점은 자체 발광을 하지 않는 '반사형'이기 때문에 눈에 피로감을 느끼진 않는다는 점이다. 컴퓨터 모니터, TV, 스마트폰 등은 LCD의 백라이트, AMOLED 등에서 직접 빛을 발산하기 때문에 피로감을 느낄 수밖에 없다. 두번째 장점은 유연하여 다양한 기판에 적용할 수 있다는 것이다. 기존의 디스플레이용 기판으로 유리(glass)를 사용하기 때문에 그 유연성에 있어 한계를 가지고 있지만, 금속 호일(Metal Foil)이나 플라스틱 기판으로 대체하려는 연구가 활발하게 진행되고 있으며 접는 것이 가능한 (Foldable) 전자종이도 출현할 전망이다. 세 번째 장점으로는 소비전력량이 적다는 것이다. 백라이트도 필요 없고, 자체적으로 빛을 낼 필요도 없고, 빛에너지를 외부에서 얻기 때문이다. 이러한 전자종이에 대한 최신 기술동향에 대하여 논하고자 한다.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2003년도 춘계학술발표강연 및 논문개요집
• /
• pp.41-41
• /
• 2003

비정질 실리콘 박막은 단결정 실리콘에 비해 저가이고 저온형성이 가능하여, 대면적/고효율의 실리콘 박막 태양전지 제작에 응용되고 있다. 태양전지에 적용하기 위해서는 우수한 암전류 및 광전류 특성을 나타내야 하고, 광학적 밴드 갭 특성 또한 중요하다. 본 연구에서는 HDP(High Density Plasma) PECVD 장비를 이용하여 나노결정립 및 비정질 실리콘 박막을 형성하고, 각 박막의 전기적, 광학적 특성을 측정, 평가하였다. 나노결정립 및 비정질 실리콘 박막의 전기적 특성은 Keithley 4200을 이용하여 암전류를 특성을 측정하였고, Solar Simulator를 이용하여 AM1.5, 100mW/$\textrm{cm}^2$ 조건에서 광전류 특성을 측정하였다. 또한, Spectrometer를 이용하여 박막의 투과율을 측정하여 Tauc Plot을 통해 광학적 밴드 갭을 계산하였다. 본 연구에서 형성된 비정질 실리콘 박막은 -$10^{6}$의 우수한 Photoresponse($\sigma$$_{ph}$ $\sigma$$_{d}$) 특성을 나타내었다. 또한, 비정질 실리콘 박막 내에 나노결정립이 형성됨에 따라 암전류는 증가하고, 광학적 밴드 갭도 증가하는 것을 알 수 있었다. 이렇게 밴드 갭이 증가된 나노결정립 실리콘 박막은 태양전지의 Window 층에 적용하면 효율 증가에 크게 기여할 것으로 판단된다.

• 한국대기환경학회지
• /
• 제29권3호
• /
• pp.287-296
• /
• 2013

To decompose carbon dioxide, which is a representative greenhouse gas, a plasma torch was designed and manufactured. To examine the characteristics of carbon dioxide decomposition via plasma discharge, a case wherein pure carbon dioxide was supplied and a case wherein methane and/or $TiCl_4$ were injected as additives were investigated and compared. The carbon dioxide and methane conversion rate, energy decomposition efficiency, produced gas concentration, carbon monoxide and hydrogen selectivity, carbon-black and $TiO_2$ were also investigated. The maximum carbon dioxide conversion rate was 28.9% when pure carbon dioxide was supplied; 44.6% when $TiCl_4$ was injected as am additive; and 100% percent when methane was injected as an additive. Therefore, this could be explained that the methane injection showed the highest carbon dioxide decomposition. Furthermore, the carbon-black and $TiO_2$ were compared with each commercial materials through XRD and SEM. It was found that the carbon-black that was produced in this study is similar for commercial materials. It was found that the $TiO_2$ that was produced in this study is suitable for photocatalyst and pigment because it has mixed anataze and rutile.

• 한국재료학회지
• /
• 제13권5호
• /
• pp.313-316
• /
• 2003

The new epitaxial base cell as a high efficiency Si solar cell was fabricated and the effect of buried contact on the cell characteristics was investigated. In our experiments, the cell with buried contact showed the open circuit voltage of 0.62 V, the short circuit current of 40 mA, the fill factor of 0.7, and the efficiency of 10% under the incident light of AM-1 100 ㎽/$\textrm{cm}^2$. The insertion of buried contact in the epitaxial base structure brought the fabricated cell to the efficiency improvement of about 33%. The cell proposed in this paper has the structural superiority in the fabrication of high efficiency solar cell due to the carrier drift transport in the optical absorption region and the formation of back surface field by $p^{－}$ $p^{+}$ epitaxial base, and the reduction of emitter series resistance by n＋ buried contact.

• 한국정밀공학회지
• /
• 제32권9호
• /
• pp.765-771
• /
• 2015

In an Additive Manufacturing (AM) system emplying the Powder Bed Fusion (PBF) system, polyamide-12 powder is currently recognized as the general material used. The Polyamide-12 powder's properties include an average particle size of 58 $58{\mu}m$, a density of 0.59 g/cm3, and melting point of $184^{\circ}C$, and can also be to used coat materials for metal powder. For this reason, the sintering process is similar to the polymer powder and polymer coated metal powder process, except during the post-process. The polyamide-12 powder has some disadvantages such as its high cost and the fact that it can only be used for the provided equipment from the maker. Therefore, this study aims to perform the applicability of new material, polymer and polymer coated metal, to the PBF system.

• International Journal of CAD/CAM
• /
• 제12권1호
• /
• pp.20-28
• /
• 2012

Finite Element Analysis (FEA) is often used to identify local stress/strain concentrations where a component is likely to fail. In order to reduce the degree of strain concentration, component thickness can be increased in those regions, or a stronger material can be used. In short fiber reinforced composite materials, strength and stiffness can be increased through proper fiber alignment. The field-aided microtailoring (FAiMTa) process is one promising method for doing this. FAiMTa uses principles of dielectrophoresis to preferentially align particles or fibers within a matrix. To achieve the preferred fiber orientation, an interdigitated electrode network must be integrated into the mold halves which can be fabricated by additive manufacturing (AM) processes. However, the process of determining the preferred fiber arrangements and electrode locations can be very challenging. This paper presents algorithms to semi-automate the interdigitated electrode design process. The algorithm has been implemented in the Solidworks CAD system and is demonstrated in this paper.

• Journal of Mechanical Science and Technology
• /
• 제20권8호
• /
• pp.1139-1148
• /
• 2006

This paper addresses the analytical modeling and dynamic response of the advanced composite rotating blade modeled as thin-walled beams and incorporating viscoelastic material. The blade model incorporates non-classical features such as anisotropy, transverse shear, rotary inertia and includes the centrifugal and coriolis force fields. The dual technology including structural tailoring and passive damping technology is implemented in order to enhance the vibrational characteristics of the blade. Whereas structural tailoring methodology uses the directionality properties of advanced composite materials, the passive material technology exploits the damping capabilities of viscoelastic material (VEM) embedded into the host structure. The VEM layer damping treatment is modeled by using the Golla-Hughes-McTavish (GHM) method, which is employed to account for the frequency-dependent characteristics of the VEM. The case of VEM spread over the entire span of the structure is considered. The displayed numerical results provide a comprehensive picture of the synergistic implications of both techniques, namely, the tailoring and damping technology on the dynamic response of a rotating thin-walled b ε am exposed to external time-dependent excitations.