• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.7
• /
• pp.607-615
• /
• 2016

This study concerns the transmission of energy and data using induced electromotive force. Due to the requirements of weapon systems, most arms are kept in an armory for a very long time before being used. During this time, the reserve battery, which serves mostly as a power supply for the electronic fuze, can be degraded, thus causing problems when it is actually needed. We attempt to solve the various problems associated with the old fuze system caused by long-term storage by using the 'induction power' transmitted from another device just before its operation, instead of using 'built-in power'. We tried to find the best carrier frequency to communicate with the system by induced electromotive force. Also, we changed the communication method for transmitting the 'induction power' from 'FM/AM modulation' to 'Duty ratio modulation', which can transmit a large amount of data in a short time. Through experiments, it was demonstrated that the induction coil can replace the reserve fuze's battery without any problem, thus confirming the possibility of using an induction coil as the power supply source of the electronic fuze.

• Journal of the Institute of Electronics Engineers of Korea CI
• /
• v.48 no.2
• /
• pp.86-95
• /
• 2011

Sensor nodes in wireless sensor networks are vulnerable to security than wired network due to using limited hardware performance and wireless communications that network topology changes frequently. Among techniques to enhance the security, the node authentication mechanism is used to defend against data forgery attacks using the ID of the node or to interfere with the routing of the network routing. In this paper, we proposed the AM-E mechanism that makes authentication key by using the energy value of node requesting authentication and performs the communication procedures for data transfer between different nodes. Because the energy value of node is changed depending on time, every time the authentication request is, an authentication key is changed. These features enhance the security of sensor networks and will help to configure the more secure WSN.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.24 no.8
• /
• pp.798-804
• /
• 2013

In this paper, conducted emission from the LDC(Low-Side DC/DC Converter) of a HEV/EV was analyzed using high-frequency circuit modeling in system-level approach. The conducted emission by PWM process(100 kHz; Switching Frequency) can cause RFI(Radio-Frequency Interference) problems in the AM/FM frequency range. In order to mitigate this conducted emission, a high-frequency equivalent circuit model is proposed by analyzing the fundamental circuits, parasitic components in their parts and connections and non-linear characteristics of MOSFETs, high-power capacitors, inverters, motors, high-power cables, and bus bars which are composed of the LDC. Using these circuit models, results of both simulation and measurement were compared and similarities between them were verified. We are looking forward that this approach can be effectively used in the EMC design of HEV/EV.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.24 no.1
• /
• pp.82-90
• /
• 2013

In this paper, conducted emission from the MDS(Motor Drive System) of a HEV/EV was analyzed using high- frequency circuit modeling in system-level approach. The conducted emission by PWM process can cause RFI(radio- frequency interference) problems in the AM/FM frequency range. In order to mitigate this conducted emission, a high-frequency equivalent circuit model is proposed by analyzing the fundamental circuits, parasitic components in their parts and connections and non-linear characteristics of IGBTs, high-power capacitors, inverters, motors, high-power cables, and bus bars which are composed of the MDS. It is confirmed that the simulated result by the proposed model is well agreed with measured results in spite of a large-scaled analysis in system level. We are looking forward that this approach can be effectively used in the EMC design of HEV/EV.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.17 no.2
• /
• pp.168-180
• /
• 1992

Commumication technology has been continuously developed to overcome the distance and time for the transmission of information to the human society. Wireless mobile communication, which had been used mostly in the military and police is widely used these days for enterprise and individuals. Therefore the domestic usage of the advanced mobile phone service are progressively gaining wide popularity. The modulation techniques used usually in mobile communications were the analog techniques such as AM and FM, but they are getting replaced by the digital techniques, However, the major disadvantage of the digital communications is the increase of the transmission bandwidth. Therefore, it is very important to use efficiently the limited frequency bandwidth. The domestic research and development on the subject seems quite limited and in order to establish the technology of the digital mobile communications. This thesis presents the design of the frequency hopping synthesizer providing 124 channels with a channel spcing of 200KHz. VCD used in the synthesizer employs a semi-rigid cable for higher purity of signal spectrum, and a hybrid pgase detector is realized with a sample hold phase detector in conjuction with a tri-state phase detedctor.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.15 no.11
• /
• pp.1043-1050
• /
• 2004

In this paper, Phase noise is analyzed and a novel approach of the nonlinear approximation including second order term of phase noise is presented to analyze and quantize system performance. As results, in QPSK-OFDM system, when PLL loop bandwidth is 5.0 Hz, 1.0 kHB, 0.5 kHz respectively, there are about 0.6 dB, 1.0 dB, 1.7 dB SNR penalties at BER=10$\^$-4/ compared with system without phase noise in AWGN channel. In 16QAM modulation, there are about 1.9 dB, 3.2 dB, 6.7 dB SNR penalties at BER=10$\^$-4/ respectively. At QPSK-OFDM system, comparing the previous linear approximation method with our proposed nonlinear approximation method, there is similar BER performance at phase noise variance lower than 0.02, but certain difference occurs as variance increases more than 0.02. Furthermore, analytical BER results closely match with simulation results in the OFDM system employing QPSK and 16qAM modulation. And, BER performance of QPSK-OFDM system is considerably degraded because of the BER error floor if the phase noise variance becomes larger than 0.03.

• Proceedings of the KOSOMBE Conference
• /
• v.1997 no.05
• /
• pp.136-140
• /
• 1997

In this paper, we proposed a implantable middle ear system using FM transmission and receiving method which has higher detection efficiency than that of AM method. And a new shape of vibrating transducer which is more efficiently vibrate than the conventional type is designed. This tranducer consist of coil and small T-type cylindrical permanent magnet. We investigated and compared the differences between conventional methods and proposed methods by quantitive analysis. We proved them by experiment.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.116-116
• /
• 2010

진공 chamber에서 방전된 plasma 내부를 외부 view port를 통하여 확인하는 것은 극히 제한적이며 leak의 확률을 높이고 plasma의 균일한 방전을 방해한다. 이를 개선하기 위하여 내장형 무선 카메라를 chamber 내부에 위치한 후 고진공 영역에서 촬영을 시도하였으나 일반적인 CCD 카메라로는 촬영할 수 없다. 고진공 영역에서 카메라 내부온도의 급격한 상승이 원인으로 밝혀졌고 적정온도인 $45^{\circ}C$를 초과하여 최대 $96^{\circ}C$까지 4 min 이내에 상승함을 IR camera로 확인할 수 있었으며 이 때 카메라가 작동하지 않았다. 또한 카메라를 고진공 영역에서 촬영 및 녹화하기 위해서는 $46^{\circ}C$의 온도를 낮추어야 함을 진공해제 이후 내부온도가 $50^{\circ}C$로 감소하면서 내장형 무선 카메라가 다시 작동함으로 인해 알 수 있었다. 본 연구에서는 이를 해결하기 위하여 내장형 무선 카메라에 AM 변조 방식의 311 MHz RF remote controller를 장착하여 외부에서 선택적으로 ON/OFF 할 수 있도록 개조하였고 10 L chamber에서 150 L/sec TMP를 이용하여 10-6 Torr의 압력에서 성공적으로 녹화 및 촬영하였다. 또한 내장형 무선 카메라 내부의 반도체 회로 규격 및 발열량과 heat sink의 규격 (열전도도, 복사율)을 추가로 조사하였다. 분자유동 영역에서 열전달은 복사에 의한 영향이 대부분이므로 내장형 무선 카메라 내부 온도를 감소시켜 카메라의 작동 시간을 연장하기 위하여 내부 회로에 emissivity가 높고 전기전도도가 낮아 회로에 영향이 없는 박막을 회로에 증착시키는 추후의 연구가 필요하다.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.13 no.2 s.29
• /
• pp.169-172
• /
• 2007

This paper presents circuit models and control algorithms of distributed generation system(DGS) which consists of Z-type converter and PWM inverter. Z-type converter which employs both the L and C passive components and shoot-through zero vectors instead qf the conventional DC/DC converter in order to step up DC-link voltage. Discrete time sliding mode control with the asymptotic observer is used for current control. This system am be used for power conversion of DC renewable energy.

• Journal of Advanced Navigation Technology
• /
• v.12 no.1
• /
• pp.1-7
• /
• 2008

International Civil Aviation Organization(ICAO) adopted VOR(Very high frequency Omni-Range) as an international standard air navigation system in 1949 and recommended every country to make use of it in formulating air route and guiding take-off and landing of an aircraft. VOR is quite a useful navigation system so that more than 2,000 VORs have been installed all over the world including 39 in Korea: however, VOR signal could be easily affected by its circumstance like a mountainous area because it provides navigation information through AM and FM of VHF carrier. Therefore this study intends to investigate how much VOR performance is affected by its circumstances. For this purpose, the performance of the 10 VORs influenced by 24 obstacles are measured and analyzed by using an aircraft equipped with measuring instruments. This study may give us a feasible solution of problems related to the VOR siting in the future.