• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2014.11a
• /
• pp.304-304
• /
• 2014

Quaternary Ti-Al-Si-N films were deposited on WC-Co substrates by a hybrid deposition system of arc ion plating (AIP) method for Ti-Al source and DC magnetron sputtering technique for Si incorporation. The synthesized Ti-Al-Si-N films were revealed to be composites of solid-solution (Ti,Al)N crystallites and amorphous $Si_3N_4$ by instrumental analyses. The Si addition in Ti-Al-N films affected the refinement and uniform distribution of crystallites by percolation phenomenon of amorphous silicon nitride, similarly to Si effect in TiN film. As the Si content increased up to about 9 at.%, the hardness of Ti-Al-N film steeply increased from 30 GPa to about 50 GPa. The highest microhardness value (~50 GPa) was obtained from the Ti-Al-Si-N film having the Si content of 9 at.%, the microstructure of which was characterized by a nanocomposite of $nc-(Ti,Al)N/a-Si_3N_4$.

• Journal of the Korean Ceramic Society
• /
• v.51 no.4
• /
• pp.337-343
• /
• 2014

A single layer ultrafiltration(UF) ceramic membrane was prepared using boehmite sol. Boehmite was synthesized using a typical sol-gel process with optimization of the viscosity, pH, molar ratio of aluminum isopropoxide(AIP) and $HNO_3$. Boehmite sol was coated on a microfiltration(MF) support using the dip-coating method. MF support was dipped into the boehmite sol with a withdrawal speed of 5 mm/s and was maintained for 10 s in the boehmite sol, resulting in a uniform UF membrane layer of $10{\mu}m$ thickness. The porosity of the obtained membrane was measured and found to be 41.2%; the pore size was found to range from 80~100 nm, corresponding to the pore size of the UF membrane. The flux of the obtained membrane was initially 540 $L/m^2h$ and approximately 85% of the initial flux was recovered using a periodic back-flushing process.

• Journal of the Korean institute of surface engineering
• /
• v.39 no.3
• /
• pp.110-114
• /
• 2006

In this work, comparative studies on microstructure and mechanical properties between $Mo_2N$ and Mo-Si-N coatings were conducted. Ternary Mo-Si-N coatings were deposited on AISI D2 steel substrates by a hybrid method, where AIP technique was combined with a magnetron sputtering technique. Instrumental analyses of XRD, HRTEM, and XPS revealed that the Mo-Si-N coatings must be a composite consisting of fine $Mo_2N$ crystallites and amorphous $Si_3N_4$. The hardness value of Mo-Si-N coatings significantly increased from 22 GPa of $Mo_2N$ coatings to about 37 GPa with Si content of 10 at.% due to the refinement of $Mo_2N$ crystallites and the composite microstructure characteristics. The average friction coefficient of the Mo-Si-N coatings gradually decreased from 0.65 to 0.4 with increasing Si content up to 15 at.%. The effects of Si content on microstructure and mechanical properties of Mo-N coatings were systematically investigated.

• Journal of The Korea Institute of Healthcare Architecture
• /
• v.29 no.4
• /
• pp.21-28
• /
• 2023

Purpose: This study is to analyze the preferences for future senior housing that reflects the characteristics of the new generation of seniors and to consider the direction of future senior housing. Methods: Data from an online survey of a new generation of older adults and group interviews with professionals and baby boomers were analyzed. The data collected from the survey and interview have been using quantitative analysed method. Literature surveys also have been carried out. Results: The results show that future senior housing requires a change in perception through conceptual expansion from the Aging in Place (AIP) to the Aging in Community (AIC) paradigm. The preferences of the new generation of seniors for future senior housing were examined to determine their preferences for location, facility size and type, unit floor plans and services, and living costs. Implications: The direction of senior housing services and architectual plans for seniors aged 55 to 65 years old were discussed.

• Journal of the Korean institute of surface engineering
• /
• v.44 no.3
• /
• pp.95-104
• /
• 2011

Ti based nanocomposite films including V, Si and Nb (Ti-Me-N, Me=V, Si and Nb) were fabricated by hybrid physical vapor deposition (PVD) method consisting of unbalanced magnetron (UBM) sputtering and arc ion plating (AIP). The pure Ti target was used for arc ion plating and other metal targets (V, Si and Nb) were used for sputtering process at a gas mixture of Ar/$N_2$ atmosphere. Mostly all of the films were grown with textured TiN (111) plane except the Si doped Ti-Si-N film which has strong (200) peak. The microhardness of each film was measured using the nanoindentation method. The minimum value of removal rate ($0.5{\times}10^{-15}\;m^2/N$) was found at Nb doped Ti-Nb-N film which was composed of Ti-N and Nb-N nanoparticles with small amount of amorphous phases.

• Journal of the Korean Ceramic Society
• /
• v.54 no.6
• /
• pp.511-517
• /
• 2017

With different working pressures and substrate biases, Cr-Al-N coatings were deposited by hybrid physical vapor deposition (PVD) method, consisting of unbalanced magnetron (UBM) sputtering and arc ion plating (AIP) processes. Cr and Al targets were used for the arc ion plating and the sputtering process, respectively. Phase analysis, and composition, binding energy, and microstructural analyses were performed using X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and field emission scanning electron microscopy (FESEM), respectively. Surface droplet size of Cr-Al-N coatings was found to decrease with increasing substrate bias. A decrease of the deposition rate of Cr-Al-N films was expected due to the increase of substrate bias. The coatings were grown with textured CrN phase and (111), (200), and (220) planes. X-ray diffraction data show that all Cr-Al-N coatings shifted to lower diffraction angles due to the addition of Al. The XPS results were used to determine the $Cr_2N$, CrN, and (Cr,Al)N binding energies. The compositions of the Cr-Al-N films were measured by XPS to be Cr 23.2~36.9 at%, Al 30.1~40.3 at%, and N 31.3~38.6 at%.

• Journal of Broadcast Engineering
• /
• v.17 no.5
• /
• pp.756-764
• /
• 2012

In current HEVC, prediction pixels are finally calculated by linear-function interpolation on two reference pixels. It is hard to expect good performance on the case of occurring large difference between two reference pixels. This paper decides more accurate prediction pixel values than current HEVC using linear function. While existing prediction process only uses two reference pixels, proposed method uses DCT-IF. DCT-IF analyses frequency characteristics of more than two reference pixels in frequency domain. And proposed method calculates prediction value adaptively by using linear-function, DCT-IF and cubic-function to decide more accurate interpolation value than to only use linear function. Cubic-function has a steep slope than linear-function. So, using cubic-function is utilized on edge in prediction unit. The complexity of encoder and decoder in HM6.0 has increased 3% and 1%, respectively. BD-rate has decreased 0.4% in luma signal Y, 0.3% in chroma signal U and 0.3% in chroma signal V in average. Through this experiment, proposed adaptive intra prediction method using DCT-IF and cubic-function shows increased performance than HM6.0.

• Tuberculosis and Respiratory Diseases
• /
• v.53 no.2
• /
• pp.136-147
• /
• 2002

Background : Interstitial lung disease has various manifestations that are differentiated by their pathology, progress and treatment. However, all manifestations eventually progresses to pulmonary fibrosis. Recent studies have shown that apoptosis of pulmonary epithelial cells might be related to pulmonary fibrosis. The correlation of the apoptotic index with the clinical manifestations, pathological findings, HRCT findings and the response to treatment were examined. Materials and Methods : Twenty subjects (14 men, 16 women), who had been diagnosed with interstitial lung disease through an open lung biopsy, were enrolled in this study. The subtypes were one AIP, two NIP, eight BOOP, and seven UIP cases. The apoptotic index was scaled from 0-2 depending on the fraction of positive staining cells by TUNEL method. The clinical severity was assessed by a modification of a previously developed CRP scoring system. The pathologic scores were based on 4 components: fibrosis, cellularity, desquamation, and granulation. In the HRCT study, each lobe was scored by the radiologists on a scale for both fibrosis and ground-glass attenuation. The treatment response was assessed by an increase in more than 10% of the CRP score, and comparing the results 3 months before and after treatment. Results : The apoptotic index showed no correlation with the CRP and HRCT scoring system. The apoptotic index correlated with the pathologic elements including fibrosis, cellularity and the desquamation score (p<0.05). Of the 16 patients who received corticosteroid therapy, 9 patients (56.3%) responded to therapy. There was no correlation between the response to corticosteroid and the apoptotic index. In the case of patients with acute and subacute ILD, the apoptotic index showed a correlation with the cellularity, desquamation, and the total histological score (p<0.05). In the case of patients with chronic ILD, the apoptotic index correlated with the fibrosis and cellularity score (p<0.05). Conclusion : Apoptosis of the pulmonary epithelial cells is implicated in the pathogenesis of interstitial lung disease particularly on a pathological basis.

• Journal of the Korean institute of surface engineering
• /
• v.49 no.6
• /
• pp.580-586
• /
• 2016

Cr-Si-Al-N coating with different Si content were deposited by hybrid physical vapor deposition (PVD) method consisting of unbalanced magnetron (UBM) sputtering and arc ion plating (AIP). The deposition temperature was $300^{\circ}C$, and the gas ratio of $Ar/N_2$ were 9:1. The CrSi alloy and aluminum targets used for arc ion plating and sputtering process, respectively. Si content of the CrSi alloy targets were varied with 1 at%, 5 at%, and 10 at%. The phase analysis, composition and microstructural analysis performed using x-ray diffraction (XRD) and field emission scanning electron microscopy (FESEM) including energy dispersive spectroscopy (EDS), respectively. All of the coatings grown with textured CrN phase (200) plane. The thickness of the Cr-Si-Al-N films were measured about $2{\mu}m$. The friction coefficient and removal rate of films were measured by a ball-on-disk test under 20N load. The friction coefficient of all samples were 0.6 ~ 0.8. Among all of the samples, the removal rate of CrSiAlN (10 at% Si) film shows the lowest values, $4.827{\times}10^{-12}mm^3/Nm$. As increasing of Si contents of the CrSiAlN coatings, the hardness and elastic modulus of CrSiAlN coatings were increased. The morphology and composition of wear track of the films was examined by scanning electron microscopy (SEM) and energy dispersive spectroscopy, respectively. The surface energy of the films were obtained by measuring of contact angle of water drop. Among all of the samples, the CrSiAlN (10 at% Si) films shows the highest value of the surface energy, 41 N/m.