• Tribology and Lubricants
• /
• 제12권2호
• /
• pp.32-40
• /
• 1996

The tribological role of copper alloy fine particles in an additive is not well known compared to solid lubricants such as $MoS_{2}$ and PTFE. In this experimental investigation, a series of friction and wear test was undertaken to gain a better understanding of an additive containing copper alloy fine particles and to identify the effectiveness of copper alloy particles in improving tribological performance of the lubricant. Friction and wear of specimens under lubricated contact condition were studied and the worn surfaces were characterized by AES (Auger Electron Spectroscopy), SEM (Scanning Electron Microscopy) and optical microscopy. It was revealed that a copper-contained layer was formed and this layer resulted in considerable reduction in both friction and wear due to its lubricity and anti-wear property. The analysis of worn surface revealed that copper of the fine alloy particles in the additive helps healing the worn surface by plating and filling wear pits.

• 센서학회지
• /
• 제13권1호
• /
• pp.66-71
• /
• 2004

Pt-doped zinc oxide (ZnO:Pt) films were deposited by ultrasonic spray pyrolysis. Resistivity variation with Pt concentration was measured. The Pt distribution in ZnO:Pt films was studied through Auger Electron Spectroscopy (AES). The ZnO:Pt films were annealed in the ambient of air, water vapor and ozone, respectively. The variation in crystallographic properties and surface morphologies with respect to the annealing condition was observed by X-Ray Diffraction (XRD) and Scanning Electron Microscopy (SEM). The resistivity variation of the films with the annealing condition was measured. Finally, Atomic Force Microscopy (AFM) measurements were carried out to study the effects of the annealing on the roughness of ZnO:Pt films.

• Bulletin of the Korean Chemical Society
• /
• 제16권7호
• /
• pp.661-666
• /
• 1995

The surface structure of the adsorption site for the identification of active sites involved in the Ziegler-Natta catalyst was studied by surface science techniques. As an example of a real catalyst, TiCl3 single crystals were prepared in a gradient furnace designed for this study and characterized by Auger Electron Spectroscopy (AES) and Low Energy Electron Diffraction (LEED) under ultrahigh vacuum condition. The chlorine covered Ti (0001) surface was employed as a model catalyst for the study of Ziegler-Natta catalyst. The diffuse LEED (DLEED) technique for the surface structural determination was applied to this disordered chlorine adsorbed on Ti (0001) surface. The diffuse scattering intensities were measured by a TV-computer method using a low light level video camera. From an analysis of two catalyst systems, the informations for the surface structure of the model catalyst surfaces were derived.

• 한국표면공학회지
• /
• 제29권5호
• /
• pp.494-497
• /
• 1996

The effect of implanted nitrogen and carbon ion into SUS 304 on the absorption of hydrogen by cathodic chaging were studied. Implantations of $N^+$, $C^+$ were performed with doses of $3\times10^{17}$ ions $\textrm{cm}^2$ and $5\times10^{17}N^+cm^2$, and $5\times10^{17}C^+cm^2$, at an energy of 90 keV. Nitrides and carbide were investigatedby X-ray diffraction, Auger electron spectroscopy (AES) and scanning electron microscope (SEM). Formation of hydrides during cathodic charging were depressed by a modified surface layer. It is concluded that the both nitrides and carbides act as the barrier of hydrogen migration and the catalyst of desorption of cathodically charged hydrogen.

• 한국재료학회지
• /
• 제26권3호
• /
• pp.109-116
• /
• 2016

To achieve the fabrication of high-quality Ag-coated Cu particles through a wet chemical process, we reported herein pretreatment conditions using an ammonium-based mixed solvent for the removal of a $Cu_2O$ layer on Cu particles that were oxidized in air for 1 hr at $200^{\circ}C$ or for 3 days at room temperature. Furthermore, we discussed the results of post-Ag plating with respect to removal level of the oxide layer. X-ray diffraction results revealed that the removal rate of the oxide layer is directly proportional to the concentration of the pretreatment solvent. With the results of Auger electron spectroscopy using oxidized Cu plates, the concentrations required to completely remove 50-nm-thick and 2-nm-thick oxides within 5 min were determined to be X2.5 and X0.13. However, the optimal concentrations in an actual Ag plating process using Cu powder increased to X0.4 and X0.5, respectively, because the oxidation in powder may be accelerated and the complete removal of oxide should be tuned to the thickest oxide layer among all the particles. Back-scattered electron images showed the formation of pure fine Ag particles instead of a uniform and smooth Ag coating in the Ag plating performed after incomplete removal of the oxide layer, indicating that the remaining oxide layer obstructs heterogeneous nucleation and plating by reduced Ag atoms.

• 한국정보통신학회논문지
• /
• 제4권3호
• /
• pp.713-719
• /
• 2000

고체상 켜쌓기법(solid phase epitaxy)으로$Ge_xSi_{1-x}/Si$(111) 이종접합을 형성하기 위해 Si(111) 기판위에 먼저 Au를 1000A 증착하고 그 위에 Ge을 1000A 증착시켜 a-Ge/Au/Si(111)구조를 형성하고 이를 고진공 조건에서 이단계 열처리 하였다. 열처리 후 Auger 전자분광분석(AES), X-ray 회절(XRD), 고분해 투과전자현미경(HRTEM) 등을 통해 Au와 Ge의 거동과 형성된 $Ge_xSi_{1-x}$막의 특성을 열처리 조건에 따라 분석하였다. a-Ge/Au/Si(111)구조는 열처리에 의해 Au/GeSi/Si(111)의 구조로 변했으며 형성된$Ge_xSi_{1-x}/$((111)층은 Si(111) 기판의 면 방향과 잘 일치하였다. 그러나 $Ge_xSi_{1-x}/Si$((111)층 내부에 적층결함, 전이, 쌍정, planar defect 등이 주로 (111)면 방향으로 형성되어 있음을 알 수 있었다.

• 한국마이크로전자및패키징학회:학술대회논문집
• /
• 한국마이크로전자및패키징학회 2000년도 Proceedings of 5th International Joint Symposium on Microeletronics and Packaging
• /
• pp.118-118
• /
• 2000

New single-source precursor, [AlCI3:NH2tBu] was synthesized for AlN thin f film processing with AICI3 (Aluminum Chloride) and tBuNH2 (tert-butylamine). AlN thin films for packaging aspplication were deposited on sapphire substrate by a atmosph하ie-pressure MOCVD. In most of other study methyl-based AI precursors w were used for source, But herein Aluminum Chloride was used for as AI source i in order to prevent the carbon contamination in the films and stabilize the p precursor. New precursor showed the very high gas vapor pressure so it allowed to m make the film under atmospheric-pressure and get the high purified film. High q quality AlN thin film was obtained at 700 to $900^{\circ}C$. The new precursor was p purified by a sublimation technique and help to fabricate high purity film. It s showed high vapor pressure, which is able to a critieal factor for the high purity a and atmospheric CVD of AlN. High Quality AIN thin film was obtained at $700-900^{\circ}C$. The AIN film was characterized by RBS

• 열처리공학회지
• /
• 제7권4호
• /
• pp.307-317
• /
• 1994

The surf ace microstructure modification by $N^+$ ion implantation into 7050Al alloy and its low cycle fatigue behavior were investigated. Ion implantation method is to physically implant accelerated ions to the surface of a substrate. High dose of nitrogen($5{\times}10^{17}ions/cm^2$) were implanted into 7050Al alloy using current density of accellerating voltage of 100KeV. The implanted layers were characterized by Electron Probe-Micro Analysis(EPMA), Auger Elecron Spectroscopy(AES), X-Ray Diffraction(XRD), X-Ray Photoelectron Spectroscopy(XPS), and Transmission Electron Microscopy(TEM). The experimental results were compared with computer simulation data. It was shown that AlN was formed to 4500 ${\AA}$ deep. The low cycle fatigue life of the $N^4$ion modified material was prolonged by about three times the unimplanted one. The improved low cycle fatigue life was attributed to the formation of AlN and the damaged region on the surface by $N^+$ ion implantation.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2009년도 춘계학술대회 논문집
• /
• pp.163-166
• /
• 2009

다중접합 초 고효율 태양전지 제조를 위해 SiC 매트릭스를 이용한 실리콘 양자점 초격자 박막을 제조하고 특성을 분석하였다. $SiC/Si_{1-x}C_x$(x ~ 0.31)로 실리콘 양자점 초격자 박막을 Si과 C target을 이용한 co-sputtering법으로 초격자 박막을 제조하고, $1000^{\circ}C$에서 20분간 열처리를 하였다. high resolution transmission electron microscopy 사진으로 약1~7nm 크기인 양자점 생성과 분포 밀도를 확인할 수 있었으며, grazing incident X-ray diffraction (GIXRD)를 통해서 Si(111)과 $\beta$-SiC(111)이 생성되었음을 알 수 있었다. Auger electron spectroscopy (AES)측정에서 stoichiometric SiC층과 Si-rich SiC층의 Si 원자농도 (56%, 69%)와 C 원자 농도 (44%, 31%)를 알 수 있었으며, Fourier transform infra-red spectroscopy (FTIR)측정에서 SiC 픽의 위치가 767에서 $800cm^{-1}$으로 이동하는 것을 알 수 있었다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 하계학술대회 논문집
• /
• pp.375-378
• /
• 2002

We investigated the reduction of etching damage by additive O$_2$ in etching gas and recovery of etching damage by O$_2$ annealing. The PZT thin films were etched using additive Ar or O$_2$ into Cl$_2$/CF$_4$ gas mixing ratio of 8/2. In order to recover ferroelectric properties of PZT thin films after etching, the etched PZT thin films were annealed at 600 C in O$_2$ atmosphere for 10 min. The remanent polarization is decreased seriously and fatigue is accelerated in the PZT sample etched in Ar/(C1$_2$+CF$_4$) plasma, whereas these characteristics are improved in O$_2$/(Cl$_2$/CF$_4$). From x-ray photoelectron spectroscopy (XPS) analysis, the intensities of Pb-O, Zr-O and Ti-O peaks are changed and the etch byproducts such as metal chloride and metal fluoride are reduced by O$_2$ annealing. From electron probe micro analyzer (EPMA) and auger electron spectroscopy(AES), O$_2$ vacancy is observed after etching. In x-ray diffraction (XRD), the structure damage in the additive O$_2$ into C1$_2$/CF$_4$ is reduced and the improvement of ferroelectric behavioral annealed sample is consistent with the increase of the (100) and (200) PZT peaks.