• Korean Journal of Applied Biomechanics
• /
• v.22 no.3
• /
• pp.325-332
• /
• 2012

This study aimed to analyze the effects of external load between male and female on angular velocity, moment, and absorbed energy of the lower-extremity joints during drop landing. The study subjects were 9 male($mass=70.82{\pm}4.64kg$, $height=1.71{\pm}0.04m$, $age=24.5{\pm}1.84years$), 9 female($mass=50.14{\pm}4.09kg$, $height=1.61{\pm}0.03m$, $age=23.6{\pm}2.62years$), without any serious musculoskeletal, coordination, balance, or joint/ligament problems for 1 year before the study. The angular velocity, flexion/extension and abduction/adduction moments, and absorbed energy of the lower-extremity joints were compared between the men and women during drop landing under 4 different conditions of external load(0%, 8%, 16%, and 24%) by using two-way repeated ANOVA(p < .05). The women landed with a greater peak angular velocity of the ankle joint, greater peak inversion moment, and lower peak hip-extension moment than the men did, under all 4 conditions. Additionally, the landing characteristics of the women were distinct from those of the men; the women showed a greater peak knee-adduction moment and greater absorbed energy of the knee joint. These differences indicate that anterior cruciate ligament(ACL) strain was greater in the women than in the men and therefore, women may be at a higher potential risk for noncontact injuries of the ACL with an increase in external load.

• The Korean Journal of Ecology
• /
• v.15 no.2
• /
• pp.137-145
• /
• 1992

When exposed to 1, 700 ml of 0.089, 0.445 or 0.890 mM/l cadmius solution, dock (rumex crispus L)plants from heavily polluted chungrangchon site absorbed 0.0404, 0.2244 or 0.4929 mM of cadmium per g dw during the first 4 hours, which were 5.0~30.8 times faster uptake rate than those of water hyacinth (eichhornia crassipes Solm. - laub). Zinc, with which cadmium generally occurs together, did not affect the uptake rate in the concentration range of 0.0306 ~0.0918 mM/l. rumex cripus from chungrangchon site and from less polluted shingalchon site, when exposed to 1, 700 ml of 0.089 mM/l solution for 3 days, removed 68.4% and 63.2%, repectively, of the cadmium initially present in the solution. And when exposed to cadmium solution of the same concentration for the second time after cadmium-free hydroponic culture for three days, these plants removed 76.1% and 66.8% of cadmium, respectively. These removal rates were not significantly different between collection sites or between exposures, but were about 2 times greater for the first exposure, and 2~5 times greater for the second exposure, than those of water hyacinth. these results incate that rumex cripus can absorb, and thus remove, large amount of cadmium ion in wastewater, and so can be used in wastewater treatment, e.g. soil trench method. since there was large difference among the plants in the ability to absorb cadmium, it should be possible to select for strain with greater ability.

• Journal of the Korean Institute of Gas
• /
• v.13 no.4
• /
• pp.22-26
• /
• 2009

In this paper, the displacement behavior and strain energy density characteristics of a safety helmet with various corrugation dampers has been analyzed based on the finite element analysis. The safety helmet is to protect impact forces and to absorb the impact energy. Three different helmet models with a corrugation damper have been compared as functions of the displacement and strain energy density characteristics when the maximum external impulsive force is imposed on the summit of the helmet. The computed FEM results show that the extruded corrugation damper is very useful to increase the damping effect of the helmet. This study indicates that the round corrugation damper may absorb the transferred impact energy successfully. Thus, this paper recommends round and long corrugation damper on the lower part of the helmet as a new design element.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.30 no.7 s.155
• /
• pp.1090-1102
• /
• 2006

The purpose of this study is to develop an improved work clothing which is much safe, comfortable, mobility and convenient than what workers currently wear at construction site. The investigation has been conducted to evaluate current work clothing to grasp any problems, discomforts and damages related to the work clothing. For the best and accurate data, hands-on investigation and a short-interview have been performed at the construction site as well as formulating a questionnaire. The questionnaires was answered by 425 workers and safety manager of 13 different construction site. The result of the questionnaire enables us to design a sample work clothing, many pa π s such as material, pattern and design have been improved. To improve the amenity of heat, the surface of a material was used by $Aerocool^{\circledR}$ fiber which contains inside dryness function. In order to absorb perspiration on the back the armpits, mesh martial that is mixture of $Coolever^{TM}$ fiber and $Mirawave^{TM}$ fiber was used to absorb perspiration in an effective manner. And a sleeve's bottom part and trousers' bottom part's cover method have been changed. Sample work clothing was shorten at the side of upper garment up to 2cm and lengthen the length of the back by 3cm. To reduce the tightness around armpit more room was given in that area. Darts were added to the elbow, the hip, and the knees that also followed an ergonomic pattern. A sample work clothing evaluated an objective assessment and subjective assessment to compare to a current work clothing. Assessment group consists of seven subject groups and nine expert groups to evaluate external appearance and adaptability to the movements. In all aspects of the test, the result of evaluation process of the sample work clothing received more positive assessment than the current work clothing.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.35 no.5
• /
• pp.561-565
• /
• 2011

The structural vehicles are steel members of square or circle tube with definite shape. These members support various components and absorb impact energy to protect passengers during accidentswhen crash happen. Structural members need to be lightweight and stable. In this study, we do an impact simulation of a CFRP square member using finite element analysis program Ls-Dyna in order to predict fracture shape and energy absorb feature of CFRP member. Also, we make square member shape of CFRP and do an impact experiment. We compare the analytical and experimental results and consider the fracture shape and energy features of CFRP members.

• Journal of the Korean Solar Energy Society
• /
• v.37 no.6
• /
• pp.69-77
• /
• 2017

The amount of solar irradiation obtained by a photovoltaic (PV) solar panel is the major factor determining the power generated by a PV system, and the array tilt angle is critical for maximizing panel radiation acquisition. There are three types of PV systems based on the manner of setting the array tilt angle: fixed, semi-fixed, and tracking systems. A fixed system cannot respond to seasonal solar altitude angle changes, and therefore cannot absorb the maximum available solar radiation. The tracking system continually adjusts the tilt angle to absorb the maximum available radiation, but requires additional cost for equipment, installation, operation, and maintenance. The semi-fixed system is only adjusted periodically (usually seasonally) to obtain more energy than a fixed system at an overall cost that is less than a tracking system. To maximize semi-fixed system efficiency, determining the optimal tilt angle adjustment schedule are required. In this research, we conducted a simulation to derive an optimal operation schedule for a semi-fixed system in Seoul, Korea (latitude $37.5^{\circ}$). We implemented a solar radiation acquisition model and PV genereation model on MATLAB. The optimal operation schedule was derived by changing the number of tilt angle adjustments throughout a year using a Dynamic Algorithm. The results show that adjusting the tilt angle 4 times a year was the most appropriate. and then, generation amount of PV system increased 2.80% compared with the fixed system. This corresponds to 99% compared to daily adjustment model. This increase would be quite valid as the PV system installation area increased.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2012.04a
• /
• pp.521-526
• /
• 2012

It is essential for the accurate time-domain prediction of broadband noise due to turbulence-cascade interaction to develop inflow/outflow boundary conditions to satisfy the following three requirements: to maintain the back ground mean flow, to nonreflect the outgoing disturbances and to generate the specified input gust. The preceding study(1) showed that Perfectly Matched Layer (PML) boundary condition was successfully applied to absorb the outgoing disturbances and to generate the specified gust in the time-domain computations of broadband noise due to interaction of incident gust with a cascade of flat-plates. In present study, PML boundary condition is extended in order to predict steady mean flow that is needed for the computation of noise due to interaction of incident gust with a cascade of airfoils. PML boundary condition is originally designed to absorb flow disturbances superimposed on the steady meanflow in the buffer zone. However, the steady meanflow must be computed before PML boundary condition is applied on the flow computation. In the present paper, PML equations are extended by introducing source term to maintain desired mean flow conditions. The extended boundary condition is applied to the benchmark problem where the meanflow around a cascade of airfoils is predicted. These illustrative computations reveal that the extended PML equations can effectively provide and maintain the target meanflow.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.22 no.7
• /
• pp.685-691
• /
• 2012

It is essential for the accurate time-domain prediction of broadband noise due to turbulence-cascade interaction to develop inflow/outflow boundary conditions to satisfy the following three requirements: to maintain the back ground mean flow, to nonreflect the outgoing disturbances and to generate the specified input gust. The preceding study showed that perfectly matched layer(PML) boundary condition was successfully applied to absorb the outgoing disturbances and to generate the specified gust in the time-domain computations of broadband noise due to interaction of incident gust with a cascade of flat-plates. In present study, PML boundary condition is extended in order to predict steady mean flow that is needed for the computation of noise due to interaction of incident gust with a cascade of airfoils. PML boundary condition is originally designed to absorb flow disturbances superimposed on the steady meanflow in the buffer zone. However, the steady meanflow must be computed before PML boundary condition is applied on the flow computation. In the present paper, PML equations are extended by introducing source term to maintain desired mean flow conditions. The extended boundary condition is applied to the benchmark problem where the meanflow around a cascade of airfoils is predicted. These illustrative computations reveal that the extended PML equations can effectively provide and maintain the target meanflow.

• KIEAE Journal
• /
• v.14 no.3
• /
• pp.105-109
• /
• 2014

The recent rising living standards, environment-friendly, well-being and health aspects of life in the basic gratification, as well as the desire for a pleasant environment emotionally environmentally friendly way of external space or industrial interest in the indoor environment, the manifestation. In particular, the biggest problem of the indoor environment has been emerged as a Sick House Syndrome indoor space that is provided to the building materials, and the impact on the domestic and the indoor environment, and clean the house in a health standards are specified as laws. The performance rating and the various materials to create environmentally-friendly standards for building materials. The more detail, Porous clay material, toxic substances released by applying the high humidity and the water itself, and to absorb the moisture, if the emissions, without a separate device, to maintain a comfortable indoor environment and at the same time, one of the causes of Sick House Syndrome breaking down harmful substances to absorb a comfortable indoor environment to maintain an environmentally-friendly building interior material studies. It is aimed at the development to multi-functional high performance eco-friendly construction materials, rather than through one feature performance, identify key features for national and international eco-friendly building materials can exert Water Vapour Adsorption raw, decomposed materials for the application and selection.

• Journal of the Korean Society of Safety
• /
• v.35 no.6
• /
• pp.85-92
• /
• 2020

Wet Scrubber reacts the incoming pollutant gas with cleaning water (water + absorbent) to absorb pollutants and release the clean air to the atmosphere. Wet scrubbers and packed tower scrubbers using this principle are widely used in businesses that emit acid gases. In particular, in the etching process using hydrochloric acid (HCl), alkaline washing water (NaOH) having a pH of about 8 to 11 is used to absorb a large amount of acid gas. However, These salts are attached to the injection nozzle (nozzle), filling material (packing), and the demister (Demister), causing air pollution, human damage, and inoperability due to clogging and acid gas discharge. Therefore, In this study, an improvement plan was proposed to manage the washing water with pH 3~4 acidic washing water. The test method takes samples from the Wet Scrubber flue measurement laboratory twice a month for 1 year. Hydrogen chloride (HCl) concentration (ppm) was measured, and nozzle clogging and scale conditions were measured, compared, and analyzed through a differential pressure gauge and a pressure gauge. As a result of the check, it was visually confirmed that the scale was reduced to 50% or less in the spray nozzle, filler, and demister. In addition, the emission limit of hydrogen chloride in accordance with the Enforcement Regulation of the Air Quality Conservation Act [Annex 8] met 3 ppm or less. Therefore, even if the washing water is operated in an acidic pH range of 3 to 4, it is expected to reduce air pollution and human damage due to clogging of internal parts, and it is expected to reduce maintenance costs such as regular cleaning or replacement of parts.