• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.33A no.6
• /
• pp.62-71
• /
• 1996

In this paper, we design tripel-mode channel filter using iris optimization technique and investigate its response. The cavity diameter is determined to resonate three orthogonal modes coincidently and inter-cavity iris is optimized in which one slot control one TE-TE mode and other TM-TM mode couplings simultaneously. Since the electric/magnectic field is variable due to slot position, the center position of the slot which handle coupling coefficients of two modes should be designe dwith optimizatin technique presented here. The implemented triple-mode filter in this paper saves its mass and volume upto 33% relating to the dual-mode filter, caused by the reduced number of cavities.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.15 no.6
• /
• pp.671-677
• /
• 2015

A novel phase interpolator (PI) based linear model of multipath ring oscillator (MPRO) is described in this paper. By modeling each delay cell as an ideal summer followed by a single pole RC filter, the oscillation frequency is derived for a 4-stage differential MPRO. It is analytically proved that the oscillation frequency increases with the growth of the forwarding factor ${\alpha}$, which is also confirmed quantitatively through simulation. Based on the proposed model, it is shown that the power to frequency ratio keeps constant as the speed increases. Running at the same speed, a 4-stage MPRO can outperform the corresponding single-stage ring oscillator (SPRO) with 27% power saving, making MPRO with a large forwarding factor ${\alpha}$ an attractive option for lower power applications.

• KIEE International Transactions on Electrophysics and Applications
• /
• v.2C no.6
• /
• pp.321-326
• /
• 2002

This paper describes the mechanical and electrical characteristics of insulating paper impregnated with diluted varnish(W-128), according to Korean Standards. The varnish was diluted with a solvent of 6 different wt%. Kraft paper and Nomex paper were impregnated with the diluted varnish in a vacuum condition, and then completely dried. As the mechanical characteristics, the thickness of the completely dried varnish, the drying time and the tensile strength of the specimens were measured, and as the electrical characteristics, the permittivity, the tan $\delta$ and the specific resistance were evaluated as well.

• The KSFM Journal of Fluid Machinery
• /
• v.14 no.6
• /
• pp.26-34
• /
• 2011

Waterhammer and slamming phenomena can occur when power is cut off due to reversal flow in pipeline and sudden close of check valve. Therefore analysis of reversal flow time, which means the time of reversal flow in pipeline due to pumping station blackout, is needed to protect facilities from waterhammer economically and efficiently. However systematic study on reversal flow time has not been done yet. So theory of reversal flow time analysis is proposed and verified with experiment using several parameters like pump specific speed, motor pole number, and characteristic curve of pipeline in this study.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.25 no.6
• /
• pp.434-439
• /
• 2016

Optical fiber splice closure serves to protect connection parts from external environment. Moreover, it functions as a connection, junction, and distribution in diverse surroundings such as aerial, underground, duct, and pole. In this research, first, the optical fiber splice closure, its configuration, and the design problem were briefly investigated. Second, the design and application for in-line cable closure were studied to satisfy its construction and technical features. The injection molding conditions and optimal design were conducted to save time and cost during the manufacturing process. Third, methods to minimize loss via of optical fiber cable while strongly fixing optical fiber cable with optical cable holder to prevent fracture were researched, and tests such as perfect air tightness and mechanical and environmental performance were conducted.

• New & Renewable Energy
• /
• v.6 no.4
• /
• pp.41-49
• /
• 2010

Over the last decade, wind turbine industry has rapidly increased around world. These days many parts of the wind generators are induction generator. But it has some problems such as gearbox failure, rotor excitation and maintenance. Thus many manufacturers are considered permanent magnet synchronous generator named PMSG and direct drive. PMSG uses NdFeB magnet has many the advantage compare with induction generator. In this study, 3MW class outer rotor type PMSG for wind turbine is proposed. The generator features 2.6m stator outer radius, 1200mm stator length, 81 pole pairs, 14 rated rpm, 42kN/$m^2$ shear force density and 94.2% efficiency. Design and analysis generator using FEM program. Then calculate and derivate no load voltage, losses, conductor temperature. To reduce total harmonic distortion and cogging torque, the stator is applied the stator skewing. And to evaluate the designed generator, compare with other generators by active mass per rating torque and torque density.

• Journal of the Korean Magnetics Society
• /
• v.19 no.6
• /
• pp.222-226
• /
• 2009

This paper presents the new design of flat electromagnetic actuator. Novel shorted turn and copper center pole are placed into existent design in order to reduce the inductance of coil and accelerate the initial response. Finite element analysis using commercial electromagnetic solver “MAXWELL” is performed to simulate the improvement of dynamic characteristics such as fast initial response and so on.

• Bulletin of the Korean Chemical Society
• /
• v.31 no.11
• /
• pp.3201-3211
• /
• 2010

Previous work on the phase-shifted version of the multichannel quantum-defect theory (MQDT) for a system involving 2 closed and many open channels (Lee, C.-W. Bull. Korean Chem. Soc. 2010, 31, 1669) was extended to obtain the formulae of the spectral shape parameters with the structure of a pole extracted explicitly for general cases only limited by 2 non-degenerate closed channels. The theory was applied to the narrow $6p_{1/2,3/2}np$ J = 1 autoionizing Rydberg series in barium perturbed by the $6p_{3/2}nf$ states obtained by de Graaff et al.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.25 no.6
• /
• pp.42-48
• /
• 2011

Generally, the structure without the stator core Axial Field Permanent Magnet (AFPM) generator was simple and there was nearly no cogging toque. And because it had the wide driving rate area, it had been being mainly used in the small wind power generation system. However, AFPM generator with non-slotted stator can't generate high voltage at low wind speed due to long air-gap. It is the reason of output efficiency drop. Therefore, in this paper, the AFPM synchronous generator with internal rotor and dual slotted stators for the small wind turbine is studied, and deal with a cogging torque minimization through the determination of optimum pole-arc ratio.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.62 no.6
• /
• pp.863-869
• /
• 2013

In this paper, we compared and analyzed for safety 1.2m rectangular anchor block and arch-type root anchor block. First, numerical analysis was performed three-dimensional nonlinear method by numerical model test using finite element analysis program "Visual FEA". Then, measure displacement of the surface of the earth after construct each anchor block at 14M electric pole and increase loads through field verification tests for safety evaluation.