• 대한치과보철학회지
• /
• 제35권4호
• /
• pp.781-792
• /
• 1997

This study was peformed to evaluate the dynamic fatigue characteristics of the dental ceramics for all-ceramic crown. A feldspathic porcelain of VMK68. glass ceramic of IPS-Empress, and glass infiltrated alumina ceramic of In-Ceram were used. Disc specimens were prepared to the final dimensions of 12 mm in diameter and 1 mm in thickness. The biaxial flexure test was conducted using a ball-on-three-ball method. 240 specimens were tested in $37^{\circ}C$ water by testing 20 samples at each of four loading rates:0.05, 0.2, 1, and 5mm/min. 60 specimens were tested in a moisture-free environment by testing 20 samples at 5mm/min. The inert strength of VMK68 was 80.25MPa, and the fatigue parameters were n=29.1, ${\sigma}_{fo}=52.90MPa$. The inert strength of IPS-Empress was 104.76MPa, and the fatigue parameters were n=32.46, ${\sigma}_{fo}=67.52MPa$. The inert strength of In-Ceram was 429.33MPa, and the fatigue parameters were n=31.46, ${\sigma}_{fo}=258.36MPa$. 10-year failure stresses of VMK68, IPS-Empress, and In-Ceram were 20.3MPa, 24.8MPa, and 93.6MPa, respectively. Failure strength and fatigue life showed the highest value in In-Ceram, and then, IPS-Empress and VMK68.

• 한국자동차공학회논문집
• /
• 제14권1호
• /
• pp.79-85
• /
• 2006

CFRP(Carbon Fiber Reinforced Plastics) of the advanced composite materials as structural materials for vehicle, has a wide application in light-weigh structural materials of airplanes, ships and automobiles because of high strength and stiffness, However, there is a design variable to be considered in practical application of the laminate composite materials, these materials are vulnerable to transverse impact. This paper is to study the effects of stacking sequence and curvature on the penetration characteristics of composite laminate shell. They are stacked to $[0_3/90_3]S,\;[90_3/0_3]s\;and\;[0_2/90_3/0]s,\;[90_2/0_3/90]s$ and their interlaminar number two and four. They are manufactured to various curvature radius (R=100, 150, 200mm and $\infty$), When the specimen is subjected to transverse impact by a steel ball, the velocity of the steel ball was measured both before and after impact by determing the time for it to pass two ballistics-screen sensors located a known distance apart. The critical penetration energy of specimen A and B with less interfaces were a little higher than those of C and D. As the curvature increases, the critical penetration energy increases linearly because the resistance to the in-plane deformation as well as bending deformation increases, which need higher critical penetration energy. The specimen A and C have higher critical penetration energy than B and D because of different stacking sequences. We examined crack length through a penetration test. For the specimen A with 2interfaces, the longest circumferential direction crack length were observed on the first interface from the impact point. For the specimen B 4-interface, the longest circumferential direction crack length were observed on the second interface from the impact point.

• 마이크로전자및패키징학회지
• /
• 제13권4호
• /
• pp.1-7
• /
• 2006

WLCSP(wafer level chip size package)는 웨이퍼 레벨에서 패키지 공정이 이루어지는 차세대 패키지 중 하나이다. WLCSP는 웨이퍼 레벨에서 패키지 공정이 이루어진다는 특징으로 인하여 웨이퍼당 생산되는 반도체 칩의 수에 따라 그 패키징 비용을 크게 줄일 수 있다는 장점이 있다. 그러나 응력 버퍼 역할을 하는 기판을 없애는 혁신적인 구조로 인하여 솔더 조인트의 신뢰성이 기존의 BGA 패키지에 비하여 취약하게 되는데, 이러한 솔더 조인트 신뢰성에 대하여 반도체 칩과 솔더볼을 연결하는 폴리머 절연층은 열팽창계수 차이에 의해 발생하는 응력을 흡수하는 중요한 역할을 하게 된다. 본 연구에서는 하이닉스에서 개발한 Omega-CSP를 사용하여 솔더볼 배열 변화와 제 1 절연층의 특성에 따른 솔더 조인트의 열피로 특성을 평가하였다. 그 결과 절연층의 특성 변화가 솔더 조인트의 열피로 특성에 주는 영향은 솔더볼 배열 구조에 따라 변화되는 것을 확인하였다.

• 마이크로전자및패키징학회지
• /
• 제16권1호
• /
• pp.7-11
• /
• 2009

본 연구에서는 electroless nickel / immersion gold (ENIG) 처리된 printed circuit board (PCB)를 무연 솔더인 Sn-3.5(wt%)Ag로 접합하였다. 리플로우 횟수를 1회부터 10회까지 다양하게 하여 리플로우 횟수가 증가함에 따른 솔더 접합부의 기계적, 전기적 특성의 변화에 대해 연구하였다. 접합부의 미세 조직 관찰을 위해 접합부 단면을 폴리싱 하여 금속간 화합물의 두께를 측정하고 종류를 분석하였다. 접합부의 기계적 특성을 평가하기 위해서 die 전단 시험을 하였는데, 리플로우 횟수가 4-5회일 때까지 전단 강도 값이 증가하다가 5회 이후로 감소하였다. 전기적 특성을 알아보기 위해 전기 저항 값을 측정하였는데, 리플로우 횟수가 증가할수록 접합부의 전기 저항 값은 점점 증가하였다.

• 한국콘텐츠학회논문지
• /
• 제19권5호
• /
• pp.624-631
• /
• 2019

본 연구에서는 리프터의 점착력이 분말 처리된 지문에 미치는 영향에 대하여 알아보고자 하였다. 먼저 5종의 리프터의 점착력을 측정하는 실험을 수행하였다. 그런 다음 4종의 분말로 슬라이드 글라스에 유류된 지문을 현출하고 리프터로 전사한 뒤, 전사된 지문의 품질을 측정하였다. ASTM D3121-17 (Rolling ball tack test) 방법을 사용하여 리프터의 점착력을 측정한 결과, 젤라틴 리프터를 제외한 다른 리프터 간의 점착력 차이는 근소하였다. 또한, 전사된 지문의 품질은 리프터의 점착력과 유의한 관계가 없음을 확인하였다. 그러나 약한 점착력을 가진 젤라틴 리프터로 전사할 경우 전사된 지문의 품질이 좋지 않다면 추가적인 전사가 가능하다는 장점이 있다.

• 열처리공학회지
• /
• 제21권1호
• /
• pp.10-19
• /
• 2008

To investigate the effect of ultrasonic nano-crystalline surface modification (UNSM) treatment on rolling contact fatigue and residual stress properties of bearing steels, this paper carried out a rolling contact fatigue test, measured residual stress and retained austenite, performed a wear test, observed microstructure, measured micro hardness, and analyzed surface topology. After the UNSM treatment, it was found that the surface became minute by over $100{\mu}m$. The micro surface hardness was changed from Hv730~740 of base material to Hv850~880 with about 20% improvement, and hardening depth was about 1.3 mm. The compressive residual stress was measured as high as -700~-900 MPa, and the quantity of retained austenite was reduced to 27% from 34%. The polymet RCF-6 ball type rolling contact fatigue test showed over 4 times longer fatigue lifetime after the UNSM treatment under 551 kgf load and 8,000 rpm. In addition, this paper observed the samples, which went through the rolling contact fatigue test, with OM and SEM, and it was found that the samples had a spalling phenomenon (the race way is decentralized) after the UNSM treatment. However, before the treatment, the samples had excessive spalling and complete exploration. Comparison of the test samples before and after the UNSM treatment showed a big difference in the fatigue lifetime, which seems to result from the complicated effects of micro particles, compressive residual stress, retained austenite, and surface topology.

• KIEAE Journal
• /
• 제10권5호
• /
• pp.187-194
• /
• 2010

Heavy-weight floor impact sound insulation performance criteria have been effective in Korea since the regulation which enforces the standard thickness of slabs in domestic apartment houses should be constructed by 180mm or 210mm was adopted. But every slab does not satisfy this criteria. So, review on existing floor impact sound insulation performance is needed to propose some basic materials for the revision of rating method. To achieve this goal, 63 field test data were checked and analyzed. The results of this study are as follows ; 1) The 210mm thickness slab has the characteristics of deeper level decrease above 120Hz frequency band than that of 180mm thickness slab's. 2) 27.5% of 180mm thickness slabs were satisfied the floor impact sound insulation performance criteria, whereas 65% of 210mm slabs do. 3) Among the main contribution frequency bands for the determination of single rating index, 63Hz was shown as the most contributive band in 210mm slabs. 4) In comparison of single rating index between bang machine test and ball test. there is a big difference between the two and this phenomenon is frequent in 210mm slab results. 5) Rating Methods for the analysis of cross-correlation between the amount of rating, the usefulness of the arithmetic mean could be secured.

• 한국표면공학회지
• /
• 제52권6호
• /
• pp.350-356
• /
• 2019

In this study, the effect of mechanical polishing of carbon steel on the tribological properties of manganese phosphate coating on carbon steel has investigated. The microstructure, surface morphology and chemical composition were analyzed by SEM, EDS, and XRD. The surface roughness test was carried out in order to calculate Rvk value by 3D laser microscopy. Also, the tribology property of manganese phosphate coating was tested by ball-on disk. In the results of EDS analysis, coating layer consists of elements such in Mn, P, Fe, and O. XRD showed that (Mn,Fe)₅H₂(PO₄)₄·4H₂O in manganese phosphate coating layer was formed by the chemical reaction between manganese phosphate and elements in carbon steel. As the mechanical polishing degree increased, the friction coefficient was reduced. The rougher the mechanical polishing degree, the better corrosion resistance was obtained.

• 한국표면공학회지
• /
• 제54권6호
• /
• pp.357-364
• /
• 2021

In this study, DLC films deposited by PECVD were evaluated to the properties of super-hydrophobic by CF₄ treatment. The structure of DLC films were confirmed by Raman Spectra whether or not mixed sp³ (like diamond) peak and sp² (like graphite) peak. And the hydrogen contents in the DLC films (F-DLC) were measured by RBS analysis. In addition, DLC films were analyzed by scratch test for adhesion, nano-indentation for hardness and tribo-meter of Ball-on-disc type for friction coefficient. In the result of analysis, DLC films had traditional structure regardless of variation of hardness at constant conditions. Also adhesion of DLC film was increased as higher material hardness. Otherwise, friction coefficient was increased as lower material hardness. The DLC films were treated by CF₄ plasma treatment to enhance the properties of super-hydrophobic. And the DLC films were measured by ESEM(Enviromental Scanning Electron Microscope) for water condensation.

• 대한물리의학회지
• /
• 제13권4호
• /
• pp.59-65
• /
• 2018

PURPOSE: The purpose of the present study is to investigate the changes in the cognitive function of elderly dementia patients residing in a residential care facility, following six weeks of brain-computer interface (BCI)-based cognitive training and to determine whether BCI-based cognitive training effectively improves their cognitive functions. METHODS: Thirty subjects diagnosed with dementia were randomly assigned to either the experimental or control group. Pre- and post-test cognitive function assessments were conducted using the mini mental state examination-Korean (MMSE-K) and Korean-dementia rating scale (K-DRS). The experimental group received BCI-based cognitive training, which consisted of games such as flying a ball and exploding a bomb, while the control group participated in music listening activities and National Health Gymnastics. Both groups engaged in a total of 18 sessions (3 times per week for 6 weeks, for 40 minutes per session). RESULTS: After 6 weeks of intervention, the experimental group had significantly increased MMSE-K scores ($19.53{\pm}1.30$ to $22.20{\pm}1.15$; p<.0011) and total K-DRS scores ($87.20{\pm}4.16$ to $99.33{\pm}1.15$; p<.0011). In addition, the experimental group showed greater cognitive improvements than the control group. CONCLUSION: The results of this study suggest that BCI-based cognitive training is a positive intervention tool for improving the cognitive function of dementia patients.