• Journal of Ocean Engineering and Technology
• /
• v.27 no.6
• /
• pp.100-105
• /
• 2013

This paper presents a sea surface reconstruction method that uses measured radar images by applying filtering techniques and identifying wave characteristics of the surrounding the Ieodo ocean research station using WaveFinder (X-band wave measurement radar), which is installed in the station. In addition, the results obtained from real radar images are used to verify the reconstructed sea surface. WaveFinder is a marine system that was developed to measure wave information in real time. The WaveFinder installed in the station could acquire sequent images for the sea surface at constant time intervals to obtain real time information (Wave height, mean wave period, wave directionality, etc.) for the wave by getting a three-dimensional spectrum by applying an FFT algorithm to the acquired sequent images and wave dispersion relation. In particular, we found the wave height using the SNR (Signal to noise ratio) of the acquired images. The wave information measured by WaveFinder could be verified by comparing and analyzing the results measured using the wave measurement instrument (Sea level monitor) in the station. Additionally, the wave field around the station could be reconstructed through the three-dimensional spectrum and the inverse FFT filtering from the analyzed results for the measured radar images. We verified the applicability of the sea surface reconstruction method by comparing the measured and simulated sea surfaces.

• Current Optics and Photonics
• /
• v.1 no.6
• /
• pp.598-603
• /
• 2017

Traditional three-dimensional (3-D) laser imaging systems are based on real aperture imaging technology, whose resolution decreases as the range increases. In this paper, we develop a novel 3-D imaging technique based on the synthetic aperture technology in which the imaging resolution is significantly improved and does not degrade with the increase of the range. We consider an imaging laser radar (ladar) system using the floodlight transmitting mode and multi-beam receiving mode. High 3-D imaging resolutions are achieved by matched filtering the linear frequency modulated (LFM) signals respectively in range, synthetic aperture along-track, and the real aperture across-track. In this paper, a novel 3-D imaging signal model is given first. Because of the motion during the transmission of a sweep, the Doppler shift induced by the continuous motion is taken into account. And then, a proper algorithm for the 3-D imaging geometry is given. Finally, simulation results validate the effectiveness of the proposed technique.

• Journal of the Korean Institute of Telematics and Electronics B
• /
• v.33B no.7
• /
• pp.154-162
• /
• 1996

The test and evaluation is a integal part of the radar development process and it consists of two parts, field test and in-house test using a standard simulated signal. To take the in-house test, the test environment is needed to generate the critical signal that is used to determine the system design parameters and consists of general urpose measurement equipments, specialized boards and operating softwares. This paper presents the in-house test environment configuration and its function for radar system. Because this test environment genrates the simulated radar signal which has arbitrary flight path and target condition, the developed test environment makes easily to evaluate the function for radar system. The program ability of test parameters makes it possible to apply a test for 2D and 3D radar system.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.14 no.5
• /
• pp.825-832
• /
• 2011

In this paper, we described the design and measurement results of a Front-End Receiver for S-band active phased array radar. The Front-End Receiver has input P1dB of -4dBm and IIP3 of 7dBm. The measurement results show that gain is $24{\pm}0.7dB$, noise figure are less than 2.3dB over the frequency range of $fc{\pm}0.2GHz$. The Front-End Receiver can protect the receiver path from large input signals with a maximum peak power of multi-kW and recovery time is less than 0.8us. The measurement results satisfy all specifications.

• Journal of Advanced Marine Engineering and Technology
• /
• v.31 no.8
• /
• pp.970-974
• /
• 2007

A mixer is a key component in the wireless communication systems. In this paper, we design a mixer which is used in a frequency modulated continuous wave(FMCW) radar system. The frequency sweep range of the radar is from 10 GHz to 11 GHz. The transmitted and received signals of the FMCW radar are applied to LO and RF ports of the mixer, respectively, but the frequency difference between the two signals, which is called "a beat frequency" is under a few KHz and depending on the distance to target. Thus the isolation between the LO and RF ports is very important factor to design this mixer. In this paper we propose a single balanced resistive mixer using GaAs MESFET for this application. We first design a single-ended type resistive mixer using a simulation tool, then design a balanced type to increase the LO-to-RF isolation of the mixer. We fabricated the mixer on the substrate of dielectric constant 10 and thickness 0.635 mm. The measured results show that the isolation and conversion loss of the mixer over the frequency band is 20dB and 10.5dB, respectively. The LO input power for operating the proposed mixer is +3dBm, which is lower than a general conventional mixer's LO power. The 1 dB compression point is 6dBm.

• Journal of IKEEE
• /
• v.23 no.2
• /
• pp.425-430
• /
• 2019

This work describes the design and characterization of a X-band power amplifier (PA) monolithic microwave integrated circuit (MMIC) using a $0.25{\mu}m$ gate length gallium nitride (GaN) high electron mobility transistor (HEMT) technology. The developed X-band power amplifier MMIC has small signal gain of over 22.7 dB and saturated output power of 43.02 dBm (20.04 W) over the entire band of 9 to 10 GHz. Maximum saturated output power is a 43.84 dBm (24.21 W) at 9.5 GHz. Its power added efficiency (PAE) is 41.0~51.24% and the chip dimensions are $3.7mm{\times}2.3mm$, generating the output power density of $2.84W/mm^2$. The developed GaN power amplifier MMIC is expected to be applied in a variety of X-band radar applications.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.29 no.12
• /
• pp.924-934
• /
• 2018

This paper describes the development and measurement results of C-band planar active phase array antenna for detecting and tracking radar(weapon-locating radar). The antenna is designed with 14 sub-arrays(12 main channels and 2 sidelobe blanking channels and approximately 3,000 elements of transmit-receive channel) to generate transmit and digital receive patterns. Using a near-field measurements facility, G/N, transmit patterns, and received patterns are measured. Receive patterns are implemented with digital beamforming by signal processing. The measurement results demonstrate that antenna design specifications were fulfilled.

• Journal of Institute of Control, Robotics and Systems
• /
• v.18 no.9
• /
• pp.863-870
• /
• 2012

This paper presents a track-to-tack information fusion algorithm using tracks of 2D and 3D radars. Before track fusion, it is needed to match the dimension of the tracks, as the tracks generated by 2D and 3D radars have different dimensions. This paper suggests how the 2D tracks are converted to the 3D tracks for track fusion. Through simulation studies, we can verify that the performance of the proposed method.

• Corrosion Science and Technology
• /
• v.3 no.6
• /
• pp.262-264
• /
• 2004

Ground Penetrating Radar (GPR) has been used to image inside concrete specimens embedded with steel bars and delamination. An imaging algorithm has been developed to improve measurement output generated from a commercial radar system. For the experiments, laboratory size concrete specimens are made with the dimensions of $1,000mm(W){\times}1,000mm(L){\times}250mm(D)$. The results have shown improved output of the radar measurements compared to commercially available processing methods.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.13 no.3
• /
• pp.193-197
• /
• 2013

This paper presents a 5-bit true time delay circuit using a standard 0.18 ${\mu}m$ CMOS process for the broadband phased array antenna without the beam squint. The maximum time delay of ~106 ps with the delay step of ~3.3 ps is achieved at 5-20 GHz. The RMS group delay and amplitude errors are < 1 ps and <2 dB, respectively. The measured insertion loss is <27 dB and the input and output return losses are <12 dB at 5-15 GHz. The current consumption is nearly zero with 1.8 V supply. The chip size is $1.04{\times}0.85\;mm^2$ including pads.