• Korean Journal of Optics and Photonics
• /
• v.16 no.4
• /
• pp.361-365
• /
• 2005

An absolute interferometer system with multiple point-sources is devised for tile 3-D measurement of rough surface profiles. The positions of the point sources are determined to be the system parameters that influence the measurement accuracy, so they are calibrated precisely prior to performing actual measurements. For the calibration, a CCD camera composed of a two-dimensional array of photo-detectors was used. Performing optimization of the cost function constructed with phase values measured at each pixel on the CCD camera, the position coordinates of each point source is precisely determined. Measurement results after calibration performed for the warpage inspection of chip scale packages (CSPs) demonstrate that the maximum discrepancy is 9.8 mm with a standard deviation o( 1.5 mm in comparison with the test results obtained by using a Form Taly Surf instrument.

• Korean Journal of Environmental Agriculture
• /
• v.31 no.3
• /
• pp.255-263
• /
• 2012

BACKGROUND: The analysis for the concentration and enantiomeric ratio of OCPs have been performed to confirm the distribution and to emonstrate the pollution characteristics of chiral OCPs in ambient air. METHODS AND RESULTS: In ambient air at coastal and inland sites, concentrations and enantiomer fractions (EFs) of heptachlor (HEPT), eptachlor epoxide (HEPX), trans-chlordane (TC), cis-chlordane (CC), xychlordane (OXY), 2,4'-DDT, 2,4'-DDD with HRGC/HRMS were investigated to understand source and distribution of chiral organochlorine pesticides (OCPs) in ambient air. The mean concentrations of OCPs in ambient air were at the range of 0.027(heptachlor)~1.279 (4,4'-DDT) pg/m3 and 0.0005 (heptachlor)~0.1043 ng/g d.w. (TC), respectively. The mean EFs of OCPs in ambient air were at the range of 0.73 (HEPX)~0.45 (CC). Both preferential depletions of (+) and (-) enantiomer were observed for CC, indicated by EFs either <0.5 or >0.5, while preferential depletions of (-) enantiomer which mean EFs <0.5 were observed for chiral OCPs except TC and MC-5. CONCLUSION: OCPs in ambient air have been distributed from soil, but some of them such as chlordane, DDT etc. might have been introduced by long-range atmospheric transport, considering EFs by chiral analysis and trajectory analysis.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2008.05a
• /
• pp.141-144
• /
• 2008

Atomization characteristics and spatial distribution of the spray emanating from an injector of liquid-propellant thruster are investigated by using dual-mode phase Doppler anemometry (DPDA). Spray characteristic parameters such as the mean velocity, Sauter mean diameter (SMD), and velocity fluctuation are measured at various locations along the spray axis as well as on the radial direction. Those data are quantified in radial profile and also used to scrutinize the correlation between diameter and turbulence intensity of spray droplets. For the better visual grasp, dynamic behavior of spray droplets along the spray stream is presented through the velocity vectors projected on the plane of geometric axis of nozzle orifice and radial coordinate.

• Journal of Drive and Control
• /
• v.11 no.3
• /
• pp.47-54
• /
• 2014

Clutches are an integral part of the automatic transmission for changing gears. Modern automatic transmissions make extensive use of wet multiple-disc clutches employing hydraulic actuation mechanism with electronic control. Although nowadays, highly advanced shifting algorithm implements the superior shift quality and transmission efficiency, its performance should be based on smooth, reliable engagement with a reasonably durable friction material as well as stable clutch piston dynamics. Particularly, clutch filling control is the crucial part of shifting process because only the open-loop control is available due to the lack of measurement. In this paper, the effect of clutch-fill control parameters on clutch piston dynamics is experimentally investigated by using clutch piston test equipment which enables the clutch piston to actuate similar to real shifting conditions. The experimental analysis results can be expected to be utilized for the calibration of proportional solenoid valve as reference current profile data in vehicle test.

• Asian-Australasian Journal of Animal Sciences
• /
• v.19 no.3
• /
• pp.418-424
• /
• 2006

This experiment was conducted to explore the efficacy of lacquer (Rhus verniciflua) supplementation on growth performance, nutrient digestibility, carcass traits and serum biochemical values in commercial broilers. Eight hundred and forty Hubbard broiler chicks (1d old) were randomly distributed and allotted to four dietary treatments for five weeks. Each treatment had 5 replicates with 42 birds each. The dietary treatments were (1) control (2) 1% lacquer, (3) 2% lacquer and 4) 4% lacquer supplied as meal in the diet. Supplementation with lacquer improved weight gain (p = 0.0960) showing a linear trend during the starter phase (0-3 wk), but weight gain, feed intake and feed conversion ratio remained unaffected at the finisher phase (4-5 wk) and overall (0-5 wk). The nutrient digestibility studies conducted after 18 and 35 days of experimental feeding showed a linear (p<0.05) increase in digestibility of CP and ether extract at both measurement timess. The carcass studies were conducted on two birds per replicate (10 per treatment) at the end of both 3 and 5 wk. The dressing percentage, liver weight, heart weight, abdominal fat and the breast meat expressed as a percentage of live weight, did not differ significantly due to treatments at both phases. The serum cholesterol and high-density lipoprotein (HDL) showed a linear decrease (p = 0.0683 and p = 0.0322, respectively) as the level of supplementation increased at 3 wk; at 5 wk serum cholesterol, HDL and triglyceride levels decreased significantly showing a positive linear effect of lacquer on fat metabolism. The meat color values such as lightness, redness and yellowness did not reveal any significant trend. Overall, it could be concluded that lacquer supplementation at higher levels did not affect growth performance, but had a positive impact on fat metabolism by influencing fat digestibility and reducing serum cholesterol and triglyceride.

• Food Science of Animal Resources
• /
• v.43 no.2
• /
• pp.245-268
• /
• 2023

The effects of phosphate alternatives on meat quality in marinated chicken were investigated with the application of chilling and freezing. Breast muscles were injected with solution of the green weight containing 1.5% NaCl and 2% sodium tripolyphosphate (STPP) or phosphate alternatives. Treatment variables consisted of no phosphate [control (-)], 0.3% sodium tripolyphosphate [control (+)], 0.3% prune juice (PJ), 0.3% oyster shell, 0.3% nano-oyster shell, and 0.3% yeast and lemon extract (YLE) powder. One-third of the meat samples were stored at 4℃ for 1 d, and the rest of the meats were kept at -18℃ for 7 d. In chilled meat, a lower drip loss was noted for control (+) and YLE, whereas higher cooking yield in YLE compared to all tested groups. Compared with control (+), the other treatments except PJ showed higher pH, water holding capacity, moisture content, lower thawing and cooking loss, and shear force. Natural phosphate alternatives except for PJ, improved the CIE L^* compared to control (-), and upregulated total protein solubility. However, phosphate alternatives showed similar or higher oxidative stability and impedance measurement compared to control (+), and an extensive effect on myofibrillar fragmentation index. A limited effect was observed for C^*, h°, and free amino acids in treated meat. Eventually, the texture profile attributes in cooked of phosphate alternatives improved except for PJ. The results indicate the high potential use of natural additives could be promising and effective methods for replacing synthetic phosphate in chilled and frozen chicken with quality enhancement.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.11 no.2
• /
• pp.145-150
• /
• 2016

The capability of accurate positioning and tracking is necessary to implement an unmanned autonomous driving system. The moving-baseline GPS Technique is a promising candidate to mitigate positioning errors of conventional GPS system. It provides accurate positioning data based on the phase difference between received signals from multiple GPS antennas mounted on the same platform. In this paper, we propose a dual-band dual-circularly-polarized antenna suitable for the moving-baseline GPS. The proposed antenna operates at GPS L1 and L2 bands, and fed by the side of the antenna instead of the bottom. The antenna is firstly designed by calculating theoretical values of key parameters, and then optimized by means of 3D full-wave simulation software. Simulation and measurement results show that the optimized antenna offers 6.1% and 3.7% bandwidth at L1 and L2, respectively, with axial ratio bandwidth of more than 1%. The size of the antenna is $73mm{\times}73mm{\times}6.4mm$, which is small and low-profile.

• Journal of KIISE:Software and Applications
• /
• v.26 no.10
• /
• pp.1143-1155
• /
• 1999

셀룰러 방식의 이동통신 시스템에서 전파의 유효신호 도달범위를 예측하기 위해서는 전파전파 모델을 이용한 예측기법이 주로 사용된다. 그러나, 전파과정에서 주변 지형지물에 의해 발생하는 전파손실은 매우 복잡한 비선형적인 특성을 가지며 수식으로는 정확한 표현이 불가능하다. 본 논문에서는 신경회로망의 함수 근사화 능력을 이용하여 전파손실 예측모델을 생성하는 방법을 제안한다. 즉, 전파손실을 송수신 안테나간의 거리, 송신안테나의 특성, 장애물 투과영향, 회절특성, 도로, 수면에 의한 영향 등과 같은 전파환경 변수들의 함수로 가정하고, 신경회로망 학습을 통하여 함수를 근사화한다. 전파환경 변수들이 신경회로망 입력으로 사용되기 위해서는 3차원 지형도와 벡터지도를 이용하여 전파의 반사, 회절, 산란 등의 물리적인 특성이 고려된 특징 추출을 통해 정량적인 수치들을 계산한다. 이와 같이 얻어진 훈련데이타를 이용한 신경회로망 학습을 통해 전파손실 모델을 완성한다. 이 모델을 이용하여 서울 도심 지역의 실제 서비스 환경에 대한 타 모델과의 비교실험결과를 통해 제안하는 모델의 우수성을 보인다.Abstract In cellular mobile communication systems, wave propagation models are used in most cases to predict cell coverage. The amount of propagation loss induced by the obstacles in the propagation path, however, is a highly non-linear function, which cannot be easily represented mathematically. In this paper, we introduce the method of producing propagation loss prediction models by function approximation using neural networks. In this method, we assume the propagation loss is a function of the relevant parameters such as the distance from the base station antenna, the specification of the transmitter antenna, obstacle profile, diffraction effect, road, and water effect. The values of these parameters are produced from the field measurement data, 3D digital terrain maps, and vector maps as its inputs by a feature extraction process, which takes into account the physical characteristics of electromagnetic waves such as reflection, diffraction and scattering. The values produced are used as the input to the neural network, which are then trained to become the propagation loss prediction model. In the experimental study, we obtain a considerable amount of improvement over COST-231 model in the prediction accuracy using this model.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2004.05a
• /
• pp.87-90
• /
• 2004

In this paper, net-shape forming of an automobile gear is investigated. Barrel, a component of automobile start motor, is adopted as a net-shape forming. In order to accomplish the goal of net-shape forming without cutting of tooth and cam after forming, forming ability is raised through billet treatment and die design. As a technique of billet treatment spheroidizing annealing of billet to get low hardness and molybdenum disulphide coating to get low contact friction between billet and die is carried out. One of critical points of die design, fillet radii variation of tooth of die is applied to get smooth surface of barrel after cold forging. As a measurement of tooth accuracy, distance between two pins and lead-tooth alignments are investigated. Cam profile accuracy is checked with a 3D measuring instrument. Results obtained from the tests revealed reasonable result with respect to design goal. By these results, the paper shows that reasonable results can be obtained by billet treatment and die design for net-shape forming.

• Nuclear Engineering and Technology
• /
• v.45 no.5
• /
• pp.613-624
• /
• 2013

Multi-dimensional two-phase phenomena occur in many industrial applications, particularly in a nuclear reactor during steady operation or a transient period. Appropriate modeling of complicated behavior induced by a multi-dimensional flow is important for the reactor safety analysis results. SPACE, a safety analysis code for thermal hydraulic systems which is currently being developed, was designed to have the capacity of multi-dimensional two-phase thermo-dynamic phenomena induced in the various phases of a nuclear system. To validate the performance of SPACE, a two-dimensional two-phase flow test was performed with slab geometry of the test section having a scale of $1.43m{\times}1.43m{\times}0.11m$. The test section has three inlet and three outlet nozzles on the bottom and top gap walls, respectively, and two outlet nozzles installed directly on the surface of the slab. Various kinds of two-dimensional air/water flows were simulated by selecting combinations of the inlet and outlet nozzles. In this study, two-dimensional two-phase void fraction profiles were quantified by measuring the local gap impedance at 225 points. The flow conditions cover various flow regimes by controlling the flow rate at the inlet boundary. For each selected inlet and outlet nozzle combination, the water flow rate ranged from 2 to 20 kg/s, and the air flow rate ranged from 2.0 to 20 g/s, which corresponds to 0.4 to 4 m/s and 0.2 to 2.3 m/s of the superficial liquid and gas velocities based on the inlet port area, respectively.