• 한국의류학회지
• /
• 제46권3호
• /
• pp.375-389
• /
• 2022

3D printing has been considered a key technology, leading the fourth industrial revolution. However, 3D printed textile still has a lot of limitations to overcome before it can be adopted as a clothing material in terms of design, flexibility and dyeability. This study aims to provide modeling design for imparting the flexibility and post-dyeing process for 3D printed textiles. The modeling types were designed to test the flexibility of 3D printed textiles. The post-dyeing process was evaluated through dye absorption depending on the resin and modeling types, respectively. The results were as follows: two types of modeling (Modeling A and B) were designed with a ring structure to test the flexibility of the 3D printed textiles. The 3D printed textiles with ring-based structure Modeling A had flexibility regardless of the hardness of resin types. In the dyeability test, softening resin (S-Resin) and hardening resin (H-Resin) were found to have good dyeability with acid dye and direct dye, respectively. The condition of S-Resin with acid dye and H-Resin with direct dye was controlled by dye absorption rate.

• 한국의류학회지
• /
• 제45권6호
• /
• pp.1052-1062
• /
• 2021

This study aims to confirm the possibility of Ultra-Violet (UV)-printed 3D printing materials using thermal polyurethane (TPU) with CMYK colors by applying an eco-friendly UV digital printing process. A UV-printed 3D printing TPU material was prepared with cycles of UV printing and CMYK colors. Dyeability of the 3D TPU samples with cycles of UV printing and CMYK were analyzed for thickness, weight, surface roughness, reflectance, colorimetry, and K/S values. The thickness and weight of 3D-printed TPU samples with cycles of UV printing are increased with overprints from 1 to 5. The surface roughness of 3D-printed TPU samples with increasing UV prints were decreased, meaning that the surface of TPU samples becomes gradually smoother. The reflectance spectra of CMYK UV-printed TPU samples showed the surface reflectance within each characteristic wavelength of CMYK. The 3D-printed TPU samples, subjected to UV printing twice or more, showed low surface reflectance. After examining the L^*a^*b^* of the 3D-printed TPU samples by the cycles of UV printing, the study found that the more UV got printed more than 2 times, the closer the color to each CMYK.

• 한국의류학회지
• /
• 제48권2호
• /
• pp.312-327
• /
• 2024

In this study, a rehabilitation 3D printed wearable device was developed by combining an assembly-type robot hand and an integral-type robot hand through fused deposition 3D printing manufacturing with various hardness TPU (Thermoplastic Polyurethane) filaments. The hardware configuration of the robot hand includes a controller designed with four motors, one small servo motor, and a circuit board. In the case of the assembly-type robot hand model, a 3D printed robot hand was assembled using samples printed with TPU of hardness 87A and 95A. It was observed that TPU with a hardness of 95A was suitable for use due to shape stability. For the integrated-type robot hand model, the external sample using TPU of hardness 95A could be modified through a cutting method, and the hardware configuration is the same as the assembly-type. The system structure of the 3D printed robot hand was improved from an individual control method to a simultaneous transmission method.Furthermore, the system architecture of an integrated 3D printed robotic hand rehabilitation device and the application of the rehabilitation device were developed.

• 한국의류산업학회지
• /
• 제19권2호
• /
• pp.134-139
• /
• 2017

This study proposes 3D printed shoe designs with patterns made by reinterpreting traditional Korean muntin patterns as customized designs that are unique to individual consumers and different from existing products. In the fashion industry, shoes with diverse designs grafted with 3D printing technology have been introduced. Artistic 3D printed shoes showcase the unique designs of designers. Functional and practical 3D printed shoes that can be worn during daily activities and during exercise have been actively developed. Traditional Korean pattern designs are also being recreated into designs reflecting the aesthetic sense of modern times with our own identity. The uniqueness of the traditional muntin patterns in geometric shapes, such as intersections of lines, rectangles, and octagons, are expressed in shoe designs with modern aesthetic senses by utilizing the traditional patterns that conform well to the modern geometric beauty of forms. This study was intended to develop 3D shoe designs that reinterpreted the motif of muntin patterns from among traditional Korean geometric patterns with a modern aesthetic sense. The octagonal patterns that express the scenery of spring can be seen through the muntins in traditional Korean-style houses were designed on the heels of shoes. Utilizing the Rhino CAD program and ProJet 660 Pro 3D printer, shoes were designed and printed. The processes for making shoes using 3D printing technology proposed in this study are significant because they represent the creation of designs in a new area. The results of this study might help in the development of 3D printed fashion products.

• 한국의류산업학회지
• /
• 제24권3호
• /
• pp.333-345
• /
• 2022

This study developed and evaluated the motion control of 3D printed fingers applied to smart gloves. Four motions were programmed by assembling the module using the Arduino program: cylindrical grasping, spherical grasping, tip-to-tip pinch gripping, and three-jaw pinch gripping. Cap and re-entrant (RE) strip types were designed to model the finger. Two types of modeling were printed using filaments of thermoplastic elastomer (TPE) and thermoplastic polyurethane (TPU). The prepared samples were evaluated using three types of pens for cylidrical grasping, three types of balls for spherical grasping, and two types of cards for tip-to-tip pinch gripping and three-jaw pinch gripping. The motion control of fingers was connected using five servo motors to the number of each control board. Cylindrical and spherical grasping were moved by controlling the fingers at 180° and 150°, respectively. Pinch gripping was controlled using a tip-to-tip pinch motion controlled by the thumb at 30° and index-middle at 0° besides a three-jaw pinch motion controlled by the thumb-index finger-middle at 30°, 0°, and 0°, respectively. As a result of the functional evaluation, the TPE of 3D-printed fingers was more flexible than those of TPU. RE strip type of 3D-printed fingers was more suitable for the motion control of fingers than the 3D-printed finger.

• 패션비즈니스
• /
• 제24권3호
• /
• pp.85-100
• /
• 2020

Recently, 3D printing technology, which is suitable for small-volume production of many varieties, has become considered a key manufacturing technology in the 4th industrial revolution. However, the nature of 3D printing technology means it is not yet able to be applied to traditional textiles due to Fabric Flexibility. The aim of this study is to investigate Textile Structural Design by finding the optimal yarn thickness for Selective Laser Sintering (SLS) 3D printed structures on geogrid dobby woven fabric that gives the optimal flexibility and tensile strength in the final product. The test results for tensile load strength of the 3D printed test samples, using 1.0mm, 0.8mm, 0.6mm and 0.4mm yarn thicknesses, showed that all were found to be above 250N, this higher than the tensile strength of 180N that is recommended for textile products. Based on these results, the four dobby structural patterns with 3D printing produced had four yarn thicknesses: 1.0mm, 0.8mm, 0.6mm, and 0.4mm. The thinner the yarn, the more flexible the fabric; as such the optimal conditions to produce SLS-based 3D printed textiles with suitable strength and flexibility used a thickness of yarn in the range of 0.4mm to 0.6mm.

• 한국의류학회지
• /
• 제46권6호
• /
• pp.1074-1087
• /
• 2022

This study reports an optimization of a 3D printed wrist brace (WB) for various tilting angles (0°, 45°, 90°) of the re-entrant (RE) pattern and thickness (2 mm, 4 mm) using thermoplastic polyurethane (TPU) filaments and thermoplastic elastomer (TPE) filaments. The actual printing time, weight, Poisson's ratio, and tensile property of the manufactured samples were analyzed. The results confirmed that the actual printing time and weight increased with increasing thickness, regardless of the filament type. All tilting angles of the WB showed a negative Poisson's ratio (NPR), the largest of which appeared at 90°. The results of the tensile property analysis showed that a 90° tilting angle also had the largest value of elongation and stress. From these results, we conclude that the most suitable wrist brace is one in which the actual printing time is low, the weight is minimized to a thickness of 2 mm, and the tilting angle of the RE pattern is 90° for good shock absorption. The choice of filaments may be decided upon according to the user's preference, since the TPU is stiff and the TPE is elastic.

• 복식문화연구
• /
• 제30권3호
• /
• pp.403-413
• /
• 2022

The purpose of this study was to develop a 3D mesh-type impact protection pad with excellent motion adaptability and functionality by applying 3D printing technology. The hexagonal 3D mesh, which constitutes the basic structure of the pad, comprises two types: small and large. The bridge connecting the basic units was designed as the I-type, V-type, IV-type, and VV-type. After evaluating the characteristics of the bridge, it was found that the V-type bridge had the highest flexibility and tensile elongation. The hip joint pad and knee pad were completed by combining the hexagonal 3D mesh structure with the optimal bridge design. The impact protection pad was printed using a fused deposition modeling-type 3D printer with a filament made of thermoplastic polyurethane material, and the protection pad's performance was evaluated. When an impact force of approximately 6,500N was applied to the pad, the force attenuation percentage was 78%, and when an impact force of approximately 8,000N was applied, the force attenuation percentage was 75%. Through these results, it was confirmed that the 3D-printed impact protection pad with a hexagonal 3D mesh structure connected by a V-shaped bridge developed in this study can adapt to changes in the body surface according to movement and provides excellent impact protection performance.

• 한국의류학회지
• /
• 제45권1호
• /
• pp.106-122
• /
• 2021

This study confirmed the mechanical properties of an auxetic re-entrant pattern prepared using 3D printing technology and its composite fabric with neoprene for the production of functional auxetic patterns/textiles for safety shoes. Samples were prepared by the tilt angle of a re-entrant pattern of 0°, 30°, 45°, 60° and 90°, and then analyzed using Poisson's ratio, bending, compression, and tensile properties. A 3D printed auxetic re-entrant pattern (3DP-RE) and its composite fabric (3DP-RE/NP) showed a negative Poisson's ratio in all tilting angles that indicated auxetic properties. The results of the bending property shown that strength of 3DP-RE/NP was 1.5 times lower than NP, but the strain improved 2.0 times. It was confirmed that the deformation of 3DP-RE/NP is possible with a low load. Each sample type of compression behavior indicated similar regardless of the tilting angles; in addition, the compression toughness of 3DP-RE/NP increased 1.2 times compared with NP. In the case of tensile properties, 3DP-RE and 3DP-RE/NP were affected by the tilting angle, samples with 90° (the opposite of load direction) showed best tensile property and toughness. 3DP-RE/NP indicated improved bending, compression, and tensile properties.

• 한국의류학회지
• /
• 제46권6호
• /
• pp.945-962
• /
• 2022

This study examines the use of traditional patterns by new Hanbok brands. A Saekdong print pattern based on previous research was developed and applied to clothing designs. A total of 488 images of printed products from the seven new Hanbok brands and 219 images from the collections of the National Folk Museum of Korea were analyzed. Traditional patterns accounted for 47.4% of the total printed products of the new Hanbok designs, with the following ratio of use, in descending order: flower patterns, traditional paintings, animals, geometrical designs, Dancheong, text and others, Jogakbo, and Saekdong. Saekdong was found in three brand products, and the color or shape was modified. To develop the Saekdong image, five colors - red, yellow, blue, white, and green - were selected. The ratio of use for each color and the width of each color were determined with reference to previous studies. The average color value was determined through color analysis of the Saekdong collections. A total of seven items were designed for the print pattern, and four items were added for coordination to consist of four styles. This study aims to use the results of this analysis to provide insights into product development using traditional patterns.