• 토지주택연구
• /
• 제3권3호
• /
• pp.299-305
• /
• 2012

음식물쓰레기 발효 소멸용 목질바이오칩의 종류별로 세공구조에 따른 음식물쓰레기 무게 감량율 및 미생물 활동성을 비교분석 하였다. 목질바이오칩을 이용한 음식물쓰레기 발효 소멸실험을 온도 $30{\sim}50^{\circ}C$, 습도 30~70% 조건의 발효 소멸 반응조에 15일간 매일 700~1,500g의 음식물쓰레기를 투입하며 실시하였다. 이 때 1,500g의 목질바이오칩을 발효 소멸 반응조에 초기에 투입하였다. 실험에 사용한 목질바이오칩의 세공구조는 미생물 혼합형(A 바이오칩), $2{\mu}m$ 마크로 세공형(B biochip), $0.1{\mu}m$ 미세공형(C 바이오칩), 점성구조형(D 바이오칩)으로 4가지 유형이었다. 실험결과, A, B, C, D 바이오칩별 발효 소멸에 의한 음식물쓰레기 무게감량율은 각각 85%, 63%, 92%, 73%이었고, C 바이오칩의 경우가 음식물쓰레기 감량율 92%로 최고값을 나타내었다. 또한, C 바이오칩은 ATP/COD $3.00{\times}10^{-10}$, ATP/TN $2.31{\times}10^{-11}$로 상대적으로 타 종류의 바이오칩보다 높은 결과를 나타내었다. 이는 발효 소멸반응에서 발생되는 미생물의 서식지를 충분히 제공하여 ATP/COD 및 ATP/TN이 높아졌고 미생물의 활동성이 강화되어 발효 소멸반응이 원활하게 진행된 결과에 기인하는 것으로 분석되었다.

• 한국결정성장학회지
• /
• 제19권1호
• /
• pp.11-14
• /
• 2009

Micro-pulling down(${\mu}-PD$)법을 이용하여 직경 2mm, 길이 $15{\sim}25\;mm$의 Zn와 Yb가 첨가된 near-stoichiometric 조성의 $LiNbO_3$ 단결정을 성장하였다. 일정 직경의 매끄럽고 결함이 없는 양질의 단결정임을 확인하였고, 결정 내 첨가된 Zn와 Yb의 조성이 고루 분포되었음을 알 수 있었다. Raman spectra를 통해 나타난 모든 peak은 $LiNbO_3$ power의 peak과 일치함을 알 수 있었고, 이를 통해 Hexagonal 구조의 $LiNbO_3$가 성장되었음을 확인할 수 있었다. Zn의 첨가량 증가에 따른 IR 영역의 투과도 비교를 통해 광손상을 억제에 효과가 있는 Zn 첨가의 역치량이 1 mol%임을 알 수 있었다.

• 한국재료학회지
• /
• 제27권12호
• /
• pp.688-694
• /
• 2017

Porous materials such as polymeric foam are widely adopted in engineering and biomedical fields. Porous materials often exhibit complex nonlinear behaviors and are sensitive to material and environmental factors including cell size and shape, amount of porosity, and temperature, which are influenced by the type of base materials, reinforcements, method of fabrication, etc. Hence, the material characteristics of porous materials such as compressive stress-strain behavior and void volume fraction according to aforementioned factors should be precisely identified. In this study, unconfined uniaxial compressive test for two types of closed-cell structure polyurethane foam, namely, 0.16 and $0.32g/cm^3$ of densities were carried out. In addition, the void volume fraction of three different domains, namely, center, surface and buckling regions under various compressive strains (10 %, 30 %, 50 % and 70 %) were quantitatively observed using Micro 3D Computed Tomography(micro-CT) scanning system. Based on the experimental results, the relationship between compressive strain and void volume fraction with respect to cell size, density and boundary condition were investigated.

• 한국재료학회지
• /
• 제13권12호
• /
• pp.825-830
• /
• 2003

Structural changes during oxidation of anisotopic mesophase carbon fiber(AMCFs) have been observed with TEM and XRD. It was shown that the AMCFs are three dimensionally stacked structure of turbostratic layers, and are non-homogeneous structure which consist of the highly ordered areas and the random areas. The $d_{ 002}$, Lc, and La of AMCFs which were measured by XRD were 3.44, 146, and $135\AA$, respectively. It was observed that the oxidation initiated at the random areas, because the $d_{002}$ / decreased to the value of 3.41 $\AA$ during initial oxidation stage. It was also observed that the La of the oxidized AMCFs increased up to 182 $\AA$ during the whole oxidation process, and the $d_{002}$ of that increases up to 9.44 $\AA$ when the burn-off is over the degree of 20%. Therefore, it was suggested that the micro-crystalline grew up by heat treatment effects during the fibers were oxidized, In addition, it was shown that there was difference in the measured value of La by XRD and TEM, in case of 39% oxidized fibers for example, the measured La was $ 165\AA$ by XRD and in the range of 180∼220 $\AA$ by TEM.

• 한국광학회지
• /
• 제14권3호
• /
• pp.312-320
• /
• 2003

본 연구에서는 355 nm의 파장을 갖는 Nd:YVO$_4$ 3고주파 DPSS 레이저를 이용하여 폴리머의 3차원 미세형상 가공기술을 개발하였다. UV레이저와 폴리머의 어블레이션에 관한 메커니즘을 설명하였으며 비교적 UV영역에서 파장이 긴 355 nm파장의 영역에서는 광열분해 반응으로 가공되고 이에 따른 폴리머의 광학적 특성을 살펴보았다. 광 흡수율 특성이 우수한 폴리머가 광가공 특성이 좋은 것으로 나타났으나 벤젠구조가 많이 포함되어 있는 폴리이미드의 경우는 광분해후 다시 새로운 화학적 결합이 이루어져 가공부 면이 좋지 않은 면을 보였다. 레이저의 다중 주사방식으로 가공하기위하여 표면의 오염이 적은 폴리카보네이트를 시편으로 사용하여 3차원 적으로 모델링한 직경 1 mm와 500 $\mu\textrm{m}$의 마이크로 팬을 가공하였다. 레이저 발진 효율이 높고 유지비가 적은 355 nm의 DPSSL을 이용한 3차원 가공기술의 개발로 향후 저비용으로 빠른 시간에 미세부품을 개발하는 기술에 기여할 것으로 예상된다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2009년도 제38회 동계학술대회 초록집
• /
• pp.365-365
• /
• 2010

Similar to the superhydrophobic surfaces of lotus leaf, water strider leg is attributed to hierarchical structure of micro pillar and nano-hair coated with low surface energy materials, by which water strider can run and even jump on the water surface. In order to mimick its leg, many effort, especially, on the fabrication of nanohairs has been made using several methods such as a capillarity-driven molding and lithography using poly(urethane acrylate)(PUA). However most of those effort was not so effective to create the similar structure due to its difficulty in the fabrication of nanoscale hairy structures with hydrophobic surface. In this study, we have selected a low surface energy polymeric material of polytetrafluoroethylene (PTFE, or Teflon) assisted with surface modification of CF4 plasma treatment followed by hydrophobic surface coating with pre-cursor of hexamethyldisiloxane (HMDSO) using a plasma enhanced chemical vapor deposition (PE-CVD). It was found that the plasma energy and duration of CF4 treatment on PTFE polymer could control the aspect ratio of nano-hairy structure, which varying with high aspect ratio of more than 20 to 1, or height of over 1000nm but width of 50nm in average. The water contact angle on pristine PTFE surface was measured as approximately $115^{\circ}$. With nanostructures by CF4 plasma treatment and hydrophobic coating of HMDSO film, we made a superhydrophobic nano-hair structure with the wetting angle of over $160^{\circ}C$. This novel fabrication method of nanohairy structures has been applied not only on 2-D flat substrate but also on 3-D substrates like wire and cylinder, which is similarly mimicked the water strider's leg.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2003년도 추계학술대회논문집
• /
• pp.101-106
• /
• 2003

Recent electronic equipment becomes smaller, more functional, and more complex. According to these trends, LTCC(low temperature co-fired ceramic) has been emerged as a promising technology in packaging industry. It consists of multi-layer ceramic sheet, and the circuit has 3D structure. In this technology via hole formation plays an important role because it provides an electric path for the packaging interconnection network. Therefore via hole quality is very important for ensuring performance of LTCC product. Via holes are formed on the green sheet that consists of ceramic(before sintering) layer and PET(polyethylene Terephthalate) one. In this paper we found the correlation between hole quality and process condition such as ceramic thickness, and tool size. The shear behavior of double layer sheet by micro hole punching which is different from that of single layer one was also discussed.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1995년도 추계학술대회 논문집
• /
• pp.1067-1070
• /
• 1995

In this paper, we have treated the modeling and development of three degree of freedom parallel manipulator for micromotion based on the Stewart platform type parallel structure. the kinematic modeling was derived from the relation between base coordinate and platform anr the dynamic modeling was from the method of Kinematic Influence Coefficients(KIC) and transferring of the generalized coordinates. Using this method, we presented the method to choose the actuator and joint by investigating the actuating forces needed when the manipulator moves along the given trajectory. In the end, the prototype manipulator was developmented and evaluated.

• 소성∙가공
• /
• 제13권1호
• /
• pp.65-71
• /
• 2004

Recent electronic equipment becomes smaller, more functional, and more complex. According to these trends, LTCC(low temperature co-fired ceramic) has been emerged as a promising technology in packaging industry. It consists of multi-layer ceramic sheet, and the circuit has 3D structure. In this technology via hole formation plays an important role because it provides an electric path for the packaging interconnection network. Therefore via hole qualify is very important for ensuring performance of LTCC product. Via holes are formed on the green sheet that consists of ceramic(before sintering) layer and PET(polyethylene terephthalate) one. In this paper we found the correlation between hole quality and process condition such as PET thickness and ceramic thickness. The shear behavior of double layer sheet by micro hole punching which is different from that of single layer one was also discussed.

• 한국정밀공학회지
• /
• 제26권12호
• /
• pp.123-130
• /
• 2009

This study presents the application of a polymer behavior model that considers fluid mechanics and heat transfer effects in a deposition system. The analysis of the polymer fluid properties is very important in the fabrication of precise microstructures. This fluid behavior model involves the calculation of velocity distribution and mass flow rates that include the effect of heat loss in the needle. The effectiveness of the proposed method was demonstrated by comparing estimated mass fluid rates with experimental values. The mass fluid rates under various process conditions, such as pressure, temperature, and needle size, reflected the actual deposition state relatively well, and the assumption that molten polycaprolactone(PCL) is a non-Newtonian fluid was reasonable. The successful fabrication of three-dimensional microstructures demonstrated that the model is valid for predicting the polymer behavior characteristics in the microstructure fabrication process. The results of this study can be used to investigate the effect of various parameters on fabricated structures before turning to experimental approaches.