• Fashion & Textile Research Journal
• /
• v.12 no.4
• /
• pp.467-476
• /
• 2010

The purpose of this study was to develop a plausible methodology based on experimental data how to set up darts and split lines on 3D parametric body dressed with tight-fit garment. The results were as following: Through the process of making convex hull, the concave parts were straightened to make a convex hull, especially in the center part of bust, under breast part and scapular part. To figure out the optimum positions of darts and split lines, the inflection points of curve ratio were searched along the horizontal polylines of waist and bust. This procedures produced reliable results with low deviation. Using Rapidform, CATIA and Unigraphics, six patches of bodice patterns were drawn and aligned. Paired t-test results showed the outline and area between 3D surface and 2D were not significantly different, meaning this method could be adaptable when flattening 3D surfaces. The amount of waist dart measured on the pattern showed that the highest portion was allocated on 2nd dart(back), followed by 1st dart(back), 1st dart(front), 2nd dart(front)/side dart, and center back dart. A series of findings suggested that curve ration inflection point could be used as a guide to set up darts and split line on 3D parametric model with low deviation.

• Journal of Advanced Navigation Technology
• /
• v.11 no.1
• /
• pp.17-23
• /
• 2007

This paper, describes the VDR physical layer design in VDL Mode-2 in order to meet the requirements of International standards. VDR's frequency band is 117.975~137MHz, and CSMA(Carrier Sense Multiple Access), D8PSK(Differential Eight Phase Shift Keyed), 25KHz's channel bandwidth use. The analysis of the isolated channel from near channels, sensitivity of the receiver, dynamic range of the receiver, linear of the transmitter and energy of spurious for linear and non-linear simulation as a requirement condition of performance of VDR and teaches the course of design. The transmitting power level should be lower than 5dB from Po1dB point and the selected IF frequency is 45MHz to suppress the spurious signals. The receiver designed has 4.5dB of Noise figure, 27.52dB of Es/No, Mixer isolation up to 30dB, IIP3 power of LNA up to +10dBm to minimize the intermodulation.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.29 no.11
• /
• pp.1399-1409
• /
• 2005

The purpose of this study was to analyze the shape of gathered skirts using a three-dimensional measurement system. And in this experiment, I try to accumulate three-dimensional data of wearing model and to figure out analyzing method made by shape of clothes. The experimental design consists of two factorial designs. I set up three different kinds of fabrics, ratio of gathers. Therefore nine samples were made. The instrument and tools for three-dimensional measurement was whole body 3D scanner. Analysis program used in experiment is RapidForm 2004 PP1 and Pattern Design 2000. Data analysis utilizes SPSS WIN 10.0 Package. T-test to effect an inspection of evidence, there was difference about measurement times. One-way ANOVA to analysis effect of gather made by gathering conditions. The following results were obtained; 1. As a result of inspecting an error several times using a three-dimension measurement system, convinced data was obtained. 2. At front, distribution of gap amount was larger than back. And as ratio of gathers increased, distribution of gap amount showed regularly. 3. After analyzing horizontal sectional figure of skirts, as a height of skirt changed from waist to the bottom of skirts, the results showed as follows. While section width, section thickness, node width, node depth increased, node count decreased. 4. With the horizontal section levels of gather skirt, the silhouette on middle hip section was similar with the silhouette of body line. And as ratio of gathers around hip section increased, nodes showed regularly. At the bottom of skirts showed different nodes by different gathering condition.

• Journal of Conservation Science
• /
• v.31 no.2
• /
• pp.131-145
• /
• 2015

Cultural assets restoration is being considered highly as a practical way to extend the lifespan of damaged cultural assets and re-highlight their value. However, restoration process has been mostly dependent on the manual work involving the experience and skill of a person performing restoration, thereby requiring much time and effort. In recent, it became possible to apply a method allowing restoration to be performed more accurately and easily according to the material characteristics and shape of cultural assets. Namely, it is to use a method of printing out the 3D shape data computed in computer as real object by using 3D printer for the restoration that has been performed manually. The missing part of a cultural asset is computed into computer data first and is printed out by using 3D printer to undergo a simple shaping process. The result of 3D printer application showed that repetitive output and shape and figure revision of digital data were possible, and it was possible to improve the degree of completedness of restoration through test output using various types of restoration materials using various materials. For the purpose of verifying the possibility of applying 3D printer to restore missing part of earthenware, two pieces of modern reproductions, namely, the Seven Treasure Incense Burner and Earthenware with Wagon Wheel Decoration, were artificially damaged. The restoration result showed that compared to manual work, it showed better effectiveness in curtailing work time and reproducing accurate shape. On the other hand, secondary manual work was slightly needed for detailed binding and to vividly express surface texture.

• Current Optics and Photonics
• /
• v.3 no.2
• /
• pp.105-110
• /
• 2019

The visible-light communication (VLC) system is a promising candidate to fulfill the present and future demands for a high-speed, cost-effective, and larger-bandwidth communication system. VLC modulates the visible-light signals from solid-state LEDs to transmit data between transmitter and receiver, but the broadcasting and the line-of-sight propagation nature of visible-light signals make VLC a communication system with a limited operating range. We present a novel architecture to increase the operating range of VLC. In our proposed architecture, we guide the visible-light signals through the fiber and amplify the dissipated signals using visible-light fiber amplifiers (VLFAs), which are the most important and the novel devices needed for the proposed architecture of the VLC. Therefore, we design, analyze, and apply a VLFA to VLC, to overcome the inherent drawbacks of VLC. Numerical results show that under given constant conditions, the VLFA can amplify the signal up to 35.0 dB. We have analyzed the effects of fiber length, active ion concentration, pump power, and input signal power on the gain and the noise figure (NF).

• The Research Journal of the Costume Culture
• /
• v.21 no.4
• /
• pp.585-595
• /
• 2013

The most researches developing pattern of compression style sportswear were targeted at the live model that has muscular body build. The purpose of this study was developing a method for classifying men's lower body types in terms of muscular body build. The 3D human body scan data and body measurements of 30s of Size Korea were analyzed. The subjects (n=203) were men between the ages of 30 and 39 years. Men's muscular body build was classified with two key dimensions, thigh girth and calf girth. The subjects were divided into four groups. From each group, average subjects (n=42) whose height and weight were close to the mean value ($mean{\pm}1/2$ S.D.) were selected. 42 subjects were divided up as four groups. Group I (n=7) was thigh and calf developed body type. Group II (n=9) was thigh developed body type. Group III (n=11) was calf developed body type. Group IV (n=15) was thigh and calf undeveloped body type. Four groups had distinct different at widths (n=4), depths (n=4), and girths (n=9) dimensions. The results showed that the muscular men in their 30s could be defined by thigh and calf girths. The thigh developed muscular men had thigh girth over 60cm and the calf developed muscular men had calf girth over 38cm. From each group one representative was selected by 3D body scan figure.

• Journal of Biomedical Engineering Research
• /
• v.19 no.2
• /
• pp.189-198
• /
• 1998

3D medical image reconstruction techniques are useful to figure out complex 3D structures from the set of 2D sections. In the paper, 3D medical image reconstruction system is constructed under PC environment and programmed based on modular programming by using Visual C++ 4.2. The whole procedures are composed of data preparation, gradient estimation, classification, shading, transformation and ray-casting & compositing. Three speed optimization techniques are used for accelerating 3D medical image reconstruction technique. One is to reduce the rays when cast rays to reconstruct 3D medical image, another is to reduce the voxels to be calculated and the other is to apply early ray termination. To implement 3D medical image reconstruction system based on PC, speed optimization techniques are experimented and applied.

• The Journal of the Korea Contents Association
• /
• v.15 no.5
• /
• pp.1-17
• /
• 2015

In domestic game market, the video game market is getting smaller and also decreasing funds and high level developers. So we need the software that can help us to make more realistic and high quality contents by non-expert developer in poor environments. In this paper, we selected global studio's animations which were scored good evaluation by public and critics as a well-made emotional expression that can convey the emotion properly. We selected movements that express emotions from the animation scripts by using Ekman's 6 basic emotions and Greimas' dynamic predicate, and then we had analyzed and categorized with the data. We also analyzed the movements for which data we needed to create specific movements to express emotions by using 'Animation Layer' that used in Unity's blending process. And suggest concept of the program that to create the emotional expression movements by using those analyzed data.

• Journal of Technologic Dentistry
• /
• v.38 no.3
• /
• pp.127-133
• /
• 2016

Purpose: Currently advanced in Dental CAD/CAM technology increase a use of Co-Cr sinter metal block at Dental CAD/CAM part traditionally it has been being used with metal casting method. There is an advantage that can leave out a step of investment and casting as well as reducing a working time to compare with conventional casting method in a dry milling. Methods: In this research, compare a deformation of before and after sinter result of Co-Cr sinter metal block. Design a specimen figure by 3D CAD software and transformed it to a STL file can be used at Dental CAD/CAM. With a transformed STL file, milled a Co-Cr sinter metal specimen by using a Dental CAD/CAM dry milling machine. It arrived at the following conclusions after measuring an outer form and thickness of a machined specimen and then after sinter measure it again in a way of before sinter measurement method. Results: It is confirmed that there is no error while a 3D design figure specimen is transformed to a Dental CAD data. It is observed that there is no error at Co-Cr sinter metal specimen which consider a length of single coping and bridge. Conclusion: It is observed that there is no deformation at a specimen of AS05 and AB05 are made of 0,5mm thickness. On the other hand, the out of range of deformation is observed at a specimen of AS10 and AB10 which are made of 1mm thickness.

• Journal of Technologic Dentistry
• /
• v.41 no.1
• /
• pp.21-27
• /
• 2019

Purpose: To evaluate 2D and 3D of occulsal, mesial-occlusal and mesial-occlusal-distal cavity of composite resin inlay. Methods: Abutment tooth 16, 36 of FDI system was selected for the study. Inlay prostheses classified as occlusal cavity (OC group), mesial-occlusal (MOC) and mesial-occlusal-distal cavity (MODC) were prepared using composite resin. Composite resin was injected with composite resin in prepared tooth cavity and then photopolymerized with UV light. Additional thermal polymerization was performed. Marginal gap of composite resin inlays were measured by digital microscope(x160) with silicone replica technique. The data was analyzed from statistical software for Kruskal-Wallis test (${\alpha}=0.05$). 3-dimensional analysis was analyzed through superimposition method. Results: The smallest 2D marginal fit measure of the three groups was $47.0{\pm}21.6{\mu}m$ in the MOC group. The largest 2D marginal was $69.1{\pm}33.8{\mu}m$ in the MODC group. In the trueness of the three groups, the most accurate figure was $14.4{\pm}2.3{\mu}m$ for the MODC group. In Precision, the most accurate figure was $14.5{\pm}4.3{\mu}m$ for the MODC group. Conclusion : In this study, 2D marginal fit of OC, MOC, and MODC cavities fabricated with composite resin was applicable to all clinical applications. In the 3D inner surface accuracy evaluation, the MODC group showed the accuracy results.