• Journal of the Korean Geosynthetics Society
• /
• v.18 no.3
• /
• pp.45-53
• /
• 2019

In this study, it was analyzed the cases of bored PHC piles designed for the building foundations. The overall length of the piles varies within a maximum of 35 m. However, the average length was 17.0 to 18.9 m depending on the kind of the bedrock, with no significant difference. The socket length entered into the bedrock was designed with approximately 58% of the whole piles being 1m, the minimum length of the specification, and up to 5m. Although the range in design efficiency was very large, on average it was about 70%, consistent with the usual known extent. Applications with low design efficiency were mainly shown on the foundation of low-rise buildings or rides with low design load. On the weathered rock, the design load, which governs the design result was widely distributed at 65 to 97% of allowable bearing capacity of ground. The ratio of allowable axial load of piles to allowable bearing capacity of ground is also widely distributed between 36 and 115%, so optimization efforts are required along with design efficiency. On the other hand, the allowable bearing capacity on the soft or hard rock was highly equal, mostly within 90% of the allowable axial load of piles. In the design, the end bearing resistance averaged over 75% of the allowable bearing capacity. However, the results of the dynamic pile load test show that the end bearing resistance was predominant under the E.O.I.D conditions, and in some cases, the end bearing resistance was at least 25% under the restrike conditions.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.8 no.4
• /
• pp.483-489
• /
• 2020

Particulate matter is divided into PM10 (particle diameter of 10 ㎛ or less) and PM2.5 (particle diameter of 2.5 ㎛ or less), which are approximately 1/5 of the thickness of the hair. Due to its effect on the human body, lung disease, arteriosclerosis and heart It is known as a carcinogen that causes various diseases such as diseases. It is known that the main cause of such fine dust is nitrogen dioxide (NOx), which is emitted from automobiles in about 57.3% of urban roadsides. Therefore, in this study, as part of the development of functional construction materials to reduce NOx generated from road transport pollutants, comparative evaluation of NOx reduction performance was conducted according to the replacement rate of cement mortar in which cement was replaced with a porous material. In addition, the NOx reduction performance of cement mortar according to the photocatalyst application method and the number of applications was compared an d evaluated. As a result of the experiment, when activated ocher was substituted by 30%, it showed a reduction effect of about 32.7%, showing the best reduction performance.

• Korean Chemical Engineering Research
• /
• v.60 no.2
• /
• pp.193-201
• /
• 2022

5-HMF(5-Hydroxymethylfurfural) and LA(levulinic acid) derived from biomass are green platform chemicals, which have a wide of potential applications as biofules and biochemicals. In this study, the kinetics of LA formation from glucose decomposition with various concentration of sulfuric acid at different temperature was investigated. The experiments were performed in a broad temperature (140-200 ℃), using H₂SO₄ (1-3 wt%) as the catalyst. Glucose solution was made by dissolving 1 g of glucose in 10 ml of H₂SO₄ solution. The reactions rates increased with temperature and the activation energy showed a similar tendency to previous reported values. Reaction time for maximum concentration of 5-HMF decreased as the temperature increased. Furthermore, the decomposition of 5-HMF was fast as the acid concentration increased. Reaction time to reach maximum concentration of levulinic acid was reduced as the acid concentration increased. Continuing to raise the temperature decreased the maximum concentration of levulinic acid and increased the amount of humins. On the basis of results, kinetic parameters help to understand mechanism of LA and 5-HMF. In addition, this study provides useful information to achieve high concentration of LA and 5-HMF from biomass.

• Journal of Embryo Transfer
• /
• v.16 no.3
• /
• pp.183-191
• /
• 2001

This study was designed to establish the superior method for IVF embryos from DNA marker-proved Hanwoo cattle. DNA markers related to marbling score were identified using DNA fingerprinting with Ml3 probe and restriction enzyme Hae III. Oocytes were aspirated from unstimulated. immature ovarian follicles using a combined method of rectal ovarian-palpation and transvaginal ultrasound-guidance(6.5MHz) under local abesthesia. The aspirated oocytes were washed twice with fresh D-PBS containing 5% FBS and were rewashed 4 to 5 times with TCM-199 containing 5% FBS. A morphological grade of I to IV was assigned to each oocyte. Data were analysed using the GLM procedure of SAS. Mean number of follicles identified on ultrasound was 5.5 $\pm$2.9 in right and 4.3 $\pm$2.8 in left ovaries, respectively. The highest follicles(16.6$\pm$2.6) were found in 5101 cow compared to others. Recovery rate of follicular oocytes in individual cow was highest in 5101 cow with 89.3% in > 2mm and 94.0% in $\leq$ 2mm follicles. Total recovery rate was significantly(P<0.01) higher in $\leq$ 2mm(85.7%, 130/154) than > 2mm follicles(74.2%, 201/271). Significantly more oocytcs of Grade IV were recovered from > 2mm follicles. Mean number follicles recovered was 4.8$\pm$3.7. 3.0$\pm$3.4 and 0.3$\pm$0.6 in $\leq$2mm, 2~6mm and $\geq$6mm follicles. respectively. Our results imply that the more fertilizablc oocytes can be recovered from invisible-immature follicles by the combination of simultaneous rectal ovarian-palpation and ultrasound-guided approach in Hanwoo cattle.

• Journal of Bio-Environment Control
• /
• v.27 no.1
• /
• pp.94-101
• /
• 2018

Mugwort (Artemisia princeps) is a medicinal plant that has a substance called euphatilin, which is effective for cell damage and gastritis recovery. The objectives of this study were to investigate the annual growth characteristics of Artemisia princeps in greenhouse and to increase the eupatiline content by environmental stresses. Growth and eupatilin content of the plants were compared after 6 weeks of seedling and subsequent 8 weeks of greenhouse cultivation. Photosynthesis of mugwort plants did not saturate even at a relatively high light intensity of $1,200{\mu}mol{\cdot}m^{-2}{\cdot}s^{-1}$. Growth rate of the plants reached its highest at two weeks after transplanting and began to decrease since 8 weeks after transplanting. The plants showed typical characteristics of a perennial herbaceous plant as they were sensitive to seasonal changes. In particular, the plants showed high growth and eupatilin content in spring and summer as vegetative growth periods, but flowering and wintering caused considerable decreases in growth and eupatilin content in fall and winter. Therefore, application of night interruption is essential for year-round cultivationof the plant. Two stresses and a elicitor were treated: drought stresses by stopping irrigation at 5, 6, 7, and 8 days before harvest; salt stresses with nutrient solution concentrations of 2, 4, 6, 8, and $10dS{\cdot}m^{-1}$ by adding sodium chloride at 3 days before harvest; and foliar applications of methyl jasmonates of 12.5, 25, 50, and $100{\mu}M$ at 3 days before harvest. Significant increase in eupatilin content was observed at drought stresses of 7- and 8-days of irrigation stop and foliar application of $25{\mu}M$ methyl jasmonate, while no significant increase observed at salt stresses. From the results, it was confirmed that the environmental treatments can improve the productivity and quality of Artemisia princeps as a phamaceutical raw material.

• International Journal of Highway Engineering
• /
• v.8 no.2 s.28
• /
• pp.63-74
• /
• 2006

During the construction of circular underground pipe, the non-proper compaction along the pipe and the decrease of compaction efficiency have been the main problems to induce the failure of underground pipe or facility. The use of CLSM (controlled low strength materials) should be one of the possible applications to overcome those problems. In this research, the full-scaled field test and the numeric analysis using PENTAGON-3D FEM program were carried out for three different cases on the change of backfill materials, including the common sand, the soil from construction site, and the CLSM. From the full-scaled test in field, the use of in-situ CLSM as backfill materials reduced the vertical and lateral deformation of the pipe, as well as the deformation of the ground surface. The main reason for reducing the deformation would be the characteristics of the CLSM, especially self-leveling and self-hardening properties. The measured earth pressure at the surround of the corrugated pipe using the CLSM backfills was the smaller than the other cases, and the absolute value was almost zero. Judging from the full-scaled field test and FEM analysis, the use of CLSM as backfill materials should be one of the best choices reducing the failure of the underground pipes.

• Resources Recycling
• /
• v.29 no.2
• /
• pp.55-61
• /
• 2020

Selective catalytic reduction (SCR) has been a promising technology to reduce the air pollution caused by nitrogen oxides (NOx) in several industries. The consumption of SCR catalysts increases every year as technology evolves, however those have a limited lifespan and usually end up in landfills after they deactivate. Currently, the most widely used catalyst for and stationary applications is V₂O₅-WO₃/TiO₂ which can contain around 50% wt V₂O₅ and 7-10% wt of WO₃. The vast uses for both vanadium and tungsten and the worldwide interest in recycling methods that allow for the extraction of metals from secondary sources represent the major motivation for this research. The extraction time, pH dependency, extraction concentration studies were carried out using Aliquat 336 in exxol D80 as the extractant. It was determined that to optimize the extraction of both metals 30min of contact time with an organic phase containing 0.5mol/L of Aliquat 336 are needed at a slightly acidic pH (~5.0). In addition, counter McCabe-Thiele studies allowed us to determine that one stage is necessary for the removal of 99% of vanadium while 2 stages are necessary for the extraction of tungsten and counter current simulations proved that the theoretical approach was correct.

• Journal of Bio-Environment Control
• /
• v.30 no.4
• /
• pp.383-392
• /
• 2021

It has been known that oyster mushrooms cultivated in facilities with thermal insulation have been strongly affected by inner environments. Forced air-circulation fans exert much direct influence on disturbing air inside the facility so the matter is of particular interest. This study is carried out to investigate the measured levels of air uniformity in a cultivation facility for oyster mushroom in the various cases that reversibly controlled air-circulation fans which drove the flow in the upward and reverse direction by turn and unidirectional fans by which the wind blew upwards only were operated from July 1 to 10. The actual survey for the selection of ongoing operation cases presented that farmers, even though there were some discrepancies, have made use of fans in a way that it paused for 5-30min after running for 5-15min by turn. The level of air uniformity in the case of adopting reversible fans revealed a slight difference of 1.4-1.8℃ (Temp.) and 7.8-8.7% (R.H.) under the condition of not using a cooler during the investigation period. By contrast, unidirectional fans showed a noticeable difference of 3.2-3.7℃ and 14.0-15.4%, which meant that air uniformity driven by reversible fans much more increased compared to that for unidirectional fans. Among the twenty operational applications considered for reversible fans, the circumstance that the wind blew upwards for 10-15min and ceased for 5-10min and blew again in the reverse direction for 10-15min in succession gave minor improvements at the level of air uniformity, but at present there was somewhat difficult to make decision on which cases were optimally best. It seems necessary that the effects of reversible fans on air uniformity as well as qualities of oyster mushrooms have to be appraised in the cultivation period and the flow visualization needs to be done to ascertain the performance of air mixture.

• Journal of Korea Technology Innovation Society
• /
• v.19 no.3
• /
• pp.465-482
• /
• 2016

Previous researches have introduced various ways to analyze the impact of standardization on innovation while the works are not only small in number but based on interview or case study. This paper addresses the impact of standardization activities within South Korean industries on technological innovation applying an empirical analysis of standardization activities and technological innovation. Drawing on Korean Industrial Standards Classification from panel data of 2003 to 2012, we employed corresponding data of each industrial classification: Number of standards, Accumulated number of standards, Number of patents applied in Korea, Sales, Operational profit, Intangible asset, and R&D invest. In the first model, we run panel data models employing the number of patents applied in Korea as an independent variable, and the number of standards, accumulated number of standards, sales, and operational profit as dependent variables to observe industrial impacts upon the relationship between standards and patents, along with time lagged consideration. The result shows that number of standards are revealed to have a negative influence on patent applications in the year of research, and no significant effect appears for the next two years while positive effect shows up on the third year. Meanwhie, accumulated number of standards turned out to have positive effects on patent applications in Korea. This implies it takes time for innovation subjects to embrace newly established standards while having a significant amount of positive effect on technological innovation in the long term. In the second model, we use canonical correlation analysis to find industrial-wide characteristics. The result of this model is equivalent to the result of panel data analysis except in a few industries, where some industry specific characteristics appear. The implications of our results present that Korean policy makers have to take account of industrial effects on standardization to promote technological innovation.

• Korean Journal of Weed Science
• /
• v.7 no.2
• /
• pp.208-219
• /
• 1987

Newly developed several herbicides were evaluated as paddy rice herbicide at the Yeongnam Crop Experiment in 1986. And also, the general situation of rice cultivation between Korea and Japan was compared. Twenty-nine herbicides of the total 59 herbicides were used as paddy rice field in Korea while these were 100 and 187, respectively, in Japan. Among paddy rice herbicides, butachlor was the most important herbicide in both countries. However, the degree of concentration to a particular herbicide was greater in Korea compared to Japan; consumption rate of single butachlor to the total herbicide were 66.5% for Korea and 11.9%r for Japan, respectively. Pyrazolate, pyrazoxyfen and quinclorac were the most promising hebicides in pressed-type rice nurserybed in terms of herbicidal efficacy and phytotoxic effect. For transplanted paddy rice field, single application of NC-311 or combining applications of NC-311 with butachlor or quinclorac gave excellent results at the weed community that was dominated by Echinochloa crus-galli, Aneilema japonica, Ludwigia prostrata, Scirpus hotarui, Cyperus serotinus, Potamogeton distinctus and Eleocharis kuroguwai. Particularly the above combining applications maintained their excellent herbicidal effect up to 3 leaf stage of E. crus-galli without arising herbicidal phytotoxicity. Pyrazolate and three sulfonyl urea herbicides (DPX-5384, NC-311 and CGA 142464) exhibited very high safety against rice. However, Japonica type rice cultivar was a little bit more sensitive than Indica/Japonica type rice cultivar. On the other hand, the effect of these herbicides against E. crus-galli was very strong. Herbicidal effect against E. crus-galli was enhanced through shoot absorption for sulfonyl urea herbicides and root abosorption for pyrazolate and quinclorac, respectively.