• Journal of Digital Contents Society
• /
• v.12 no.3
• /
• pp.355-360
• /
• 2011

In this paper, the performance of OFDM (Orthogonal Frequency Division Multiplexing) was assessed by using computer simulations performed using Matlab. We analyzed channel estimation algorithm for adaptive modulation techniques and effect of system using designed simulator in Multimedia wireless communication multipath fading channel environment. Also, we analyzed performance of adaptive OFDM systems that apply adaptive equalizer using guided result through BER. In result, in case of adaptive modulation OFDM systems that modulation mode changes according to channel state, we knew that adaptive modulation OFDM systems have gains of about 7dB performance than general system (BER=$10^{-1}$). Thus we know that adaptive OFDM propose systems is required for efficient transmission in the high speed Multimedia wireless communication channel environment.

• Journal of the Korea Society for Simulation
• /
• v.15 no.3
• /
• pp.87-91
• /
• 2006

With the growth of the internet, the number of wireless internet users has increased continuously up to date. However, mobile communications could not support high speed transmission rate with cheap communication fee and wireless LAN has problems in providing terminal mobility and wide area connectivity, respectively. So the WMAN standard has been newly designed to make up for these limits. The initial 802.16 specification effectively offers a solution for providing fixed users with high speed wireless communication but it does not offer terminal mobility. So the 802.16d and 802.16e have been developed as the next generation solution that can support various PHY layer (SC, SCa, OFDM, OFDMA) and offer the terminal mobility. In this paper, we propose an effective uplink scheduling algorithm for VoIP with using UGS, and we show that our proposed algorithm is superior in view of average delay and management of uplink bandwidth to conventional rtPS algorithm and the scheme in reference, with using NS-2 network simulator.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.11 no.12
• /
• pp.2205-2209
• /
• 2007

In this paper, a voltage controlled oscillator(VCO) of core components for wireless subscriber network is designed. The type of oscillator is colpits method and the oscillator device uses a LC resonator. The product is made on FR-4 substrate with dielectric constant of 4.6. The designed VCO is operated at 3.2V, 10mA and has output value of 0.67dB. The VCO's phase noise property is -102DBc/Hz at offset frequence of 100kHz. The fabricated VCO is the same as target value and can be used for wireless subscriber network.

• KIPS Transactions on Computer and Communication Systems
• /
• v.3 no.12
• /
• pp.455-462
• /
• 2014

In recent years, various services in mobile environments due to the growth of mobile devices and related techniques like wireless networks. Furthermore, as the increasing communication traffic in cellular networks has become a new significant issue, many studies for device-to-device(D2D) communication and D2D-based cooperative services have been performed recently. In this paper, we design a smart agent system for D2D-based cooperative services and propose a dynamic service binding method based on service ontology. We classify roles of mobile devices for cooperative services by defining three types of smart agents, and construct a knowledge base in order to describe properties of 'service' unit. The proposed knowledge model, D2D cooperative service ontology, can enable a autonomous cooperative services between mobile devices by binding a requested service to the appropriate member device according to the real-time context in mobile environments.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.3 no.2 s.5
• /
• pp.69-74
• /
• 2004

In this work, A PLDRO (Phase Locked Dielectric Resonator Oscillator) which can be used for the wireless communication systems fur MMC(Microwave Micro Cell) and ITS wireless communication system is designed. A different approach to the PLDRO structure is applied for phase locking by dual phase lock loop structure. The proposed dual loop PLDRO generates the output power of 0 dBm at 18.7 GHz and has the characteristics of a phase noise of -80 dBc/Hz at 1kHz, -83 dBc/Hz at 10 kHz offset frequency from carrier frequency

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.45 no.4
• /
• pp.131-136
• /
• 2008

Two Ka-band 3-stage power amplifiers were designed and fabricated using $0.18-{\mu}m$ CMOS technology. For low loss matching networks for the amplifiers, two substrate-shielded transmission line structures, having good modeling accuracy up to 40 GHz were used. The measured insertion loss of substrate-shielded microstrip-line (MSL) was 0.5 dB/mm at 27 GHz. A 3-stage CMOS amplifier using substrate-shielded MSL achieved a 14.7-dB small-signal gain and a 14.5-dBm output power at 27 GHz in a compact chip area of 0.83$mm^2$. The measured insertion loss of substrate-shielded coplanar waveguide (CPW) was 1.0 dB/mm at 27 GHz. A 3-stage amplifier using substrate-shielded CPW achieved a 12-dB small-signal gai and a 12.5-dBm output power at 26.5 GHz. This results shows a potential of CMOS technology for low cost short-range wireless communication components and system.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.6 no.4
• /
• pp.286-292
• /
• 2006

This paper presents the design of a low-voltage wide-band switched-capacitor (SC) filter for wireless communication receiver applications. The filter is the 5th-order Elliptic lowpass filter. With the clock frequency of 50MHz implying that an effective sampling frequency is 100MHz with double sampling scheme, the cut-off frequency of the filter is programmable to be 1.25MHz, 2.5MHz, 5MHz and 10MHz. For low-power systems powered by a single-cell battery, the SC filter was elaborately designed to operate at 1.2V power supply. Simulation result shows that the 3rd-order input intercept point (IIP3) can be up to 27dBm. The filter was fabricated in a $0.25-{\mu}m$ 1P5M standard CMOS technology and measured frequency responses show good agreement with the simulation ones. The current consumption is 34mA at a 1.2V power supply.

• Journal of information and communication convergence engineering
• /
• v.8 no.3
• /
• pp.289-294
• /
• 2010

In the vehicle communication system, transferred information is needed to be detected as possible as fast in order to inform car status located in front and rear side. Through the moving vehicle information, we can avoid the crash caused by sudden break of front one or acquire to real time traffic data to check the detour road. To be connecting the wireless communication between the vehicles, fast timing synchronization can be a key factor. Finding out the sync point fast is able to have more marginal time to compensate the distorted signals caused by channel variance. Thus, we introduce the combination method which helps find out the start of frame quickly. It is executed by auto-correlation and cross-correlation simultaneously using only short preambles. With taking the absolute value at the implemented synch block output, the proposed method shows much better system performance to us.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.11 no.2
• /
• pp.1-6
• /
• 2011

In this paper, an 1.5Gbit/s wireless data transmission system using the carrier frequency of 300 GHz band was implemented. The RF front-end was composed of schottky diode sub-harmonic mixer, frequency tripler, and horn antennas for transmitter and receiver, respectively. The LO frequencies of sub-harmonic mixer are 150GHz for transmit chain and 156GHz for receive chain. The ASK(Amplitude Shift Keying) modulation was used in the transmitter and the envelope detection method was used in the heterodyne receiver. The conversion loss of sub-harmonic mixer and implementation system loss were measured to be 9.8dB and 1.2dB, respectively. The 1.5Gbit/s video signal with HD-SDI format was transmitted over wireless distance of 40cm without optical lens(4.2m with optical lens) and displayed on HDTV at the transmitted average output power of $20{\mu}W$.

• Proceedings of the IEEK Conference
• /
• 2001.06a
• /
• pp.417-420
• /
• 2001

In this paper, a transceiver using waveguide modules for 60 GHz band wireless LAN is implemented and analyzed. The characteristics of millimeter-wave transmitter are 0 dbm output power, 10.5 dB gain and 38 dBc spurious emition. The receiver's are 3.16 dB noise figure, 8.8 dB gain, -86dBm sensitivity. Maximum communication distance is more than loom. Intermediate frequency comply with IEEE 802.11b. The transfer of multimedia files is performed. The transceiver's data rate can vary with intermediate frequency bandwidth and the transceiver is designed more than 200 Mbps.