• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.9
• /
• pp.1023-1029
• /
• 2010

In this paper, we proposed the broadband polarization diversity antenna operating in the PCS, WCDMA and WiBro band for mobile base station. We designed the antenna using the dipole antenna of the square loop type and microstrip feeding structure. Additionally, we used the choke box to remove the distortion of radiation patterns by the reflector structure when operating broadband. The simulation was performed using MWS in a commercial tool of CST company and the antenna was fabricated on a teflon substrate with 3.33 of the relative permittivity. The proposed antenna has the bandwidth of 640 MHz(from 1.75 to 2.39 GHz) when VSWR is below 1.5. At the operating bands, the interisolation between the cross-pair radiators is less than -25 dB and the maximum gains for PCS, WCDMA and WiBro band are 8.9, 8.2 and 8.6 dBi, respectively.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.27 no.1
• /
• pp.20-26
• /
• 2016

This paper presents an X-band two-stage power amplifier using GaN-HEMT. Two-stage structure was adopted to take its high gain and simple inter-stage matching network. Based on a 3D EM simulation, the bond-wire inductance and the parasitic capacitance were predicted. By reducing bond-wire inductance, Q of the matching network is decreased and the bandwidth is improved. The implemented two-stage PA shows a power gain of more than 16 dB, saturated output power of more than 42.5 dBm, and a efficiency of more than 35 % in frequency range of 8.1~8.5 GHz with an operating voltage of 40 V.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.3
• /
• pp.209-216
• /
• 2003

We design and fabricate slot array antenna for BMWS(Broadband Multimedia Wireless System) applications. This paper presents a simple feed structure, which consists of two horns and a parallel-plate waveguide, because antennas operating at 40.5 GHz~43.5 GHz have considerable feeding losses. The simple feed structure has the advantages of high-efficiency and mass-production. The fabricated antenna has a gain of 25.8 dBi with a sidelobe level below -18 ㏈ and a 3 ㏈ beamwidth of approximately 3$^{\circ}$ in the E-plane. In case of H-plane, a 3 ㏈ beamwidth is 17$^{\circ}$ and a sidelobe level is suppressed to below -27 ㏈. The experimental results are in good agreement with the simulation results. The authors expect that narrow 3 ㏈ beamwidth is obtained by combining a few proposed slot array antennas in parallel.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.11
• /
• pp.1228-1238
• /
• 2012

In this paper, we design, fabricate and measure two kinds of high-frequency packages for K-band CMOS FMCW radar chips using RF via structures. The packages are fabricated with the conventional PCB process and LTCC process. The design centering of the packages is performed at 24 GHz and impedance variation caused by the wire bonding and RF via structure is fully evaluated using 3D electromagnetic simulation. The RF via structure with characteristic impedance of $50{\Omega}$ is used to reduce impedance mismatch loss. Two kinds of test packages with back-to-back connected RF paths are fabricated and measured for the design verification of the PCB-based package and LTCC package. Their measured results show an insertion loss of less than 0.4 dB at 24 GHz and less than 0.5 dB for 20~29 GHz. The measured return loss is less than -13 dB for the PCB-based package and less than -15 dB for the LTCC package in the frequency band, but the return loss of the package itself is predicted to be better than that of the test package by about 5 dB, because the ripples of the back-to-back connection typically degrade the return loss by 5 dB or more.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.13 no.8
• /
• pp.819-826
• /
• 2002

In this paper, the performance of Au / $Ba_{0.5}Sr_{0.5}TiO_3$ (BST) / Magnesium oxide (MgO) two-layered electrically tunable band-pass Filters (BPFs) is demonstrated. The devices consist of microstrip, coplanar waveguide (CPW), and conductor-backed coplanar waveguide (CBCPW) structures. These BST thin film band-pass filters have been designed by the 2.5 D field simulator, IE3D, Zeland Inc., and fabricated by thin film process. The simulation results, using the 2-pole microstrip, CPW, and CBCPW band-pass filters, show the center frequencies of 5.89 GHz, 5.88 GHz, and 5.69 GHz, and the corresponding insertion losses are 2.67 dB, 1.14 dB, and 1.60 dB, with 3 %, 9 %, and 7 % bandwidth, respectively. The measurement results show the center frequencies of 6.4 GHz, 6.14 GHz, and 6.04 GHz, and their corresponding insertion losses are 6 dB, 4.41 dB, and 5.41 dB, respectively, without any bias voltage. With the bias voltage of 40 V, the center frequencies for the band-pass filters are measured to be 6.61 GHz, 6.31 GHz, and 6.21 GHz, and their insertion losses are observed to be 7.33 dB, 5.83 dB, and 6.83 dB, respectively. From the experiment, the tuning range for the band-pass filters are determined as about 3 % ~ 8 %.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.17 no.8 s.111
• /
• pp.760-766
• /
• 2006

In this paper, we present a wideband patch antenna with folded and shorted structure for 5 GHz WLAN(Wireless Local Area Network). The proposed antenna used folded and shorted structure in the rectangular patch for miniaturization and wide frequency bandwidth. The antenna was designed by using 3D simulation program, HFSS(High Frequency Structure Simulator) software of the Ansoft company and the implemented antenna was measured by using HP 8720c network analyzer and far field measurement chamber. Simulation result on the return loss shows fairly good characteristic of at least 13.41dB in whole frequency range of interests, and the 10dB bandwidth is 1,523MHz which shows wide bandwidth characteristic. And the simulated maximum gain of the proposed antenna is 6.57 dBi at 5.825GHz. Measured result for the 10dB bandwidth of the implemented folded and shorted structure antenna is 1,377 MHz. Measured maximum gain of the implemented antenna is 6.87dBi at 5.775GHz. Measured results for the implemented antenna showed applicable performances for the 5 GHz WLAN.

• International Journal of Contents
• /
• v.11 no.3
• /
• pp.63-68
• /
• 2015

A novel unit cell for a high pass filter was designed based on a composite right/left-handed structure that uses a folded coplanar waveguide. The equivalent circuit model for the unit cell was extracted from the geometry of the unit cell, and the effect of each main parameter of the unit cell was analyzed. The equations to calculate the immittance values of the equivalent circuit elements were formulated, and moreover, the dispersion characteristics and energy the distributions of the electromagnetic fields were simulated to determine the characteristics of the composite right/left-handed structure. Finally, the high pass filters were implemented as a series of the proposed unit cells. We show that the experimental results were in good agreement with those obtained from the simulation. Thus, the high pass filter was found to achieve a baseband insertion loss of 3 dB and a stopband attenuation of 70 dB.

• Proceedings of the KSME Conference
• /
• 2007.05b
• /
• pp.2500-2505
• /
• 2007

The vacuum interrupter (VI) is used for medium-voltage switching circuits due to its abilities and advantages as a compact and environmental friendly circuit breaker. In general, the application of a sufficiently strong axial magnetic field (AMF) permits the arc to be maintained in a diffused mode to a high-current vacuum arc. A full understanding of the vacuum arc physics is very important since it can aid to improve the performance of vacuum interrupter. In order to closely examine the vacuum arc phenomena, it is necessary to predict the magnetohydrodynamic (MHD) characteristics by the multidisciplinary numerical modeling, which is coupled with the electromagnetic and hydrodynamic fields, simultaneously. In this study, we have investigated the electromagnetic behaviors of high-current vacuum arcs for two different types of AMF contacts, which are coil-type and cup-type, using a commercial finite element analysis (FEA) package, ANSYS. The present results are compared with those of MAXWELL 3D, a reliable electromagnetic analysis software, for verification.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.58 no.7
• /
• pp.1321-1328
• /
• 2009

In this paper, an electromagnetic force driving actuator (EMFA) and three-link mechanism are proposed as a driving mechanism and connection device for low voltage air circuit breaker (ACB). As the result of dynamic characteristic analysis, the actuator and link mechanism are designed from the simulation and manufactured. The magneitc field of the EMFA is analyzed using the finite element method (FEM). The dynamic characteristic analysis with calculation of the circuit equation and kinetical equation is performed by the time difference method (TDM). Also, the result of the analysis is verified through the experiment of the fabrication model. In this paper, the EMFA size is smaller than the actuator for high voltage circuit breaker. Thus, the dynamic characteristic is analyzed with end-winding inductance that is calculated by the same method which is applied on the circle type end-winding of motors. The designed model for 1600 ampere-frame ACB and the three-link mechanism for connecting contact part with actuating part are manufactured. It is confirmed that the three-link mechanism is possible for improving the circuit breaker efficiency and reducing the size of the EMFA. It is proved that the improved 2-D analysis is more accurate than established method.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.30 no.6
• /
• pp.518-521
• /
• 2019

In this paper, an active antenna module operating in the 60 GHz band is designed and fabricated by combining a commercial transmitter chip and patch array antenna. The designed module is composed of an antenna PCB and a PCB with a transmitter chip. The frequency-control and bias-control signals are applied to the transmitter chip, using an Arduino kit. A baseband I/Q signal is also applied to the chip. A ring hybrid balun converts the output of the transmitter module to a single output, which is the output of the transmitter chip that outputs a differential output. The output is delivered to the $2{\times}4$ microstrip patch array antenna PCB as a micro-computer connector. The radiation pattern of the millimeter-wave signal of the final output is compared with the simulation results. The measured radiation patterns of the fabricated active antenna module confirm that the positions of the 3 dB beam width and null point agree well with the simulation results.