• Journal of Periodontal and Implant Science
• /
• 제54권3호
• /
• pp.189-204
• /
• 2024

Purpose: This pilot study was conducted to develop a novel test setup for the in vitro assessment of the primary stability of dental implants. This was achieved by characterising their long-term behaviour based on the continuous recording of micromotions resulting from dynamic and cyclic loading. Methods: Twenty screw implants, each 11 mm in length and either 3.8 mm (for premolars) or 4.3 mm (for molars) in diameter, were inserted into the posterior region of 5 synthetic mandibular models. Physiological masticatory loads were simulated by superimposing cyclic buccal-lingual movement of the mandible with a vertically applied masticatory force. Using an optical 3-dimensional (3D) measuring system, the micromotions of the dental crowns relative to the alveolar bone resulting from alternating off-centre loads were concurrently determined over 10,000 test cycles. Results: The buccal-lingual deflections of the dental crowns significantly increased from cycle 10 to cycle 10,000 (P<0.05). The deflections increased sharply during the first 500 cycles before approaching a plateau. Premolars exhibited greater maximum deflections than molars. The bone regions located mesially and distally adjacent to the loaded implants demonstrated deflections that occurred synchronously and in the same direction as the applied loads. The overall spatial movement of the implants over time followed an hourglass-shaped loosening pattern with a characteristic pivot point 5.5±1.1 mm from the apical end. Conclusions: In synthetic mandibular models, the cyclic reciprocal loading of dental implants with an average masticatory force produces significant loosening. The evasive movements observed in the alveolar bone suggest that its anatomy and yielding could significantly influence the force distribution and, consequently, the mechanical behaviour of dental implants. The 3D visualisation of the overall implant movement under functional cyclic loading complements known methods and can contribute to the development of implant designs and surgical techniques by providing a more profound understanding of dynamic bone-implant interactions.

• Journal of International Society for Simulation Surgery
• /
• 제3권2호
• /
• pp.69-73
• /
• 2016

Traditionally 2D cephalometric analysis has been used for diagnosis and treatment of maxillofacial deformities. However, 2D has some limitations in diagnosis and treatment planning especially facial asymmetry cases. The most weakness of 2D is overlapping and unpredictability. Today 3D treatment tools are used by many maxillofacial surgeons. 3D treatment tools can show ungarbled facial anatomy and do virtual surgery. The aim of this report is to present usefulness of using 3D analysis and virtual orthognathic surgery for severe facial asymmetry patients.

• Carbon letters
• /
• 제13권3호
• /
• pp.161-166
• /
• 2012

Carbon materials were synthesized by pyrolysis from fibers of Corn-straw (Zea mays), Rice-straw (Oryza sativa), Jute-straw (Corchorus capsularis) Bamboo (Bombax bambusa), Bagass (Saccharum officinarum), Cotton (Bombax malabaricum), and Coconut (Cocos nucifera); these materials were characterized by scanning electron microscope, X-ray diffraction (XRD), and Raman spectra. All carbon materials are micro sized with large pores or channel like morphology. The unique complex spongy, porous and channel like structure of Carbon shows a lot of similarity with the original anatomy of the plant fibers used as precursor. Waxy contents like tyloses and pits present on fiber tracheids that were seen in the inherent anatomy disappear after pyrolysis and only the carbon skeleton remained; XRD analysis shows that carbon shows the development of a (002) plane, with the exception of carbon obtained from bamboo, which shows a very crystalline character. Raman studies of all carbon materials showed the presence of G- and D-bands of almost equal intensities, suggesting the presence of graphitic carbon as well as a disordered graphitic structure. Carbon materials possessing lesser density, larger surface area, more graphitic with less of an $sp^3$ carbon contribution, and having pore sizes around $10{\mu}m$ favor hydrogen adsorption. Carbon materials synthesized from bagass meet these requirements most effectively, followed by cotton fiber, which was more effective than the carbon synthesized from the other plant fibers.

• Imaging Science in Dentistry
• /
• 제36권1호
• /
• pp.49-54
• /
• 2006

Purpose : To evaluate accuracy and reliability of program to measure facial soft tissue thickness using 3D computed tomographic images by comparing with direct measurement. Materials and Methods : One cadaver was scanned with a Helical CT with 3 mm slice thickness and 3 mm/sec table speed. The acquired data was reconstructed with 1.5 mm reconstruction interval and the images were transferred to a personal computer. The facial soft tissue thickness were measured using a program developed newly in 3D image. For direct measurement, the cadaver was cut with a bone cutter and then a ruler was placed above the cut side. The procedure was followed by taking pictures of the facial soft tissues with a high-resolution digital camera. Then the measurements were done in the photographic images and repeated for ten times. A repeated measure analysis of variance was adopted to compare and analyze the measurements resulting from the two different methods. Comparison according to the areas was analyzed by Mann-Whitney test. Results : There were no statistically significant differences between the direct measurements and those using the 3D images (p>0.05). There were statistical differences in the measurements on 17 points but all the points except 2 points showed a mean difference of 0.5 mm or less. Conclusion : The developed software program to measure the facial soft tissue thickness using 3D images was so accurate that it allows to measure facial soft tissues thickness more easily in forensic science and anthropology.

• The Korean Journal of Pain
• /
• 제33권1호
• /
• pp.48-53
• /
• 2020

Background: The aim of this study was to clarify the topographical relationship between the accessory nerve (AN) and transverse cervical artery (TCA) to provide safe and convenient injection points for AN blockade. Methods: This study included 21 and 30 shoulders of 14 embalmed Korean adult cadavers and 15 patients, respectively, for dissection and ultrasound (US) examination. Results: The courses of the TCA and AN in the scapular region were classified into four types based on their positional relationships. Type A indicated the nerve that was medial to the artery and ran parallel without changing its location (38%). In type B (38%), the nerve was lateral to the artery and ran parallel without changing its location. In type C (19%), the nerve or artery traversed each other only once during the whole course. In type D (5%), the nerve or artery traversed each other more than twice forming a twist. At the levels of lines I-IV, the nerve was relatively close to the artery (approximately 10 mm). TCAs were observed in all specimens around the superior angle of the scapula at the level of line II, whereas they were not found below line VI. In US images of the patients, the TCA was commonly observed at the level of line II (93.3%) where all ANs and TCAs were observed in cadaveric dissection. Conclusions: The results expand the current knowledge of the relation between the AN and TCA, and provide helpful information for selective diagnostic nerve blocks in the scapular region.

• Journal of Chest Surgery
• /
• 제12권3호
• /
• pp.207-214
• /
• 1979

This 3-year-old girl was observed frequent exertional dyspnea and cyanosis at crying since birth. She was not premature baby and delivered at full term normally. On physical examination, she was underdeveloped-body weight 13.5 kg, height 99 cm.- and cyanotic. There was severe clubbing on fingers. There was grade II/VI ejection systolic murmur on left lateral border of the sternum. The preoperative examinations [EKG, echocardiogram, cardiac catheterization and biventriculogram] showed that complicated T.G.A. combined vena cava[S.D.D.]. Preoperatively, we decided the corrective surgery of Rastelli operation using a. pulmonary valved conduit. The operation was performed under total circulatory arrest using deep profound hypothermia combining with extracorporeal circulation. On operation, the anatomy of the heart showed that, 1. The subaortic conus was seen and subaortic muscles were hypertrophied. 2. The VSD[type II], behind the subaortic conus-about 1 cm. in diameter, was visible only through LV cavity and, 3. The pulmonary valve ring was hypoplastic and pulmonary valvular stenosis was seen also. The subpulmonic area [LV outflow tract] was obstructed with hypertrophied muscle and mitral valve. 4. Left superior vena cava was drained to RA via coronary sinus. 5. LAD coronary artery was originated from right coronary artery and ran anterior to the pulmonary artery. According to above anatomy, we performed the VSD closure with Teflon patch, and Mustard operation combined with LV-to-pulmonary artery bypass graft using the valve contained [Hancock 16 mm] conduit. Postoperatively, adequate blood pressure could be maintained under the state of using inotropic agent [epinephrine]. On the second postoperative day, the patient died of cardiac arrest due to low cardiac output syndrome, acute renal failure and pulmonary edema.

• Applied Microscopy
• /
• 제37권4호
• /
• pp.239-248
• /
• 2007

암세포가 있는 장소의 온도를 변화시키는 것은 하나의 암 치료 방법이 될 수 있다. 명확한 기전은 아직 잘 밝혀져 있지 않지만, 고온은 미토콘드리아로 신호를 전달해서 cytochrome c를 분비시키는 세포자멸사로의 길로 유도하는 것으로 알려져 있다. 저온은 $30^{\circ}C$ 미만에서 세포자멸사를 유도하지만 심하지 않은 저온에서는($35{\sim}33^{\circ}C$ 혹은 $31{\sim}29^{\circ}C$)오히려 세포자멸사를 막는 것으로 알려져 있다. CC-t6와 GB-d1세포 주는 림프절로 전이된 사람의 담관암과 담낭암에서 확립한 것으로, 이와 같은 전이성 암세포가 온도 변화에 어떻게 반응을 하는지를 연구하기 위해 고온노출($37{\rightarrow}43^{\circ}C$)과 저온노출($37{\rightarrow}17.4^{\circ}C$)을 시행하였다. 세포의 종류나 온도 변화를 통한 스트레스의 방법과 관계없이 죽는 세포가 관찰되었으며, 고온노출이 가장 심한 영향을 주었다. 이런 죽어가는 세포는 세포자멸사가 아닌 세포괴사의 경로를 거치고 있었다. 투과전자현미경을 이용한 관찰에서 세포자멸사적인 모습은 보이지 않았고, caspase-3, -9, cytochrome c, Bax 같은 세포자멸사와 관련된 단백질의 변화도 관찰되지 않았고, 열충격단백질 70과 27도 증가하였다. 결국 CC-t6와 GB-d1 세포는 온도변화를 통한 스트레스를 주었을 경우 세포괴사로 죽음을 알 수 있었다. 온도변화를 통한 스트레스는 열충격단백질의 증가와 함께 세포괴사를 일으켰다. GB-d1과 CC-t6 세포에서 고온은 가장 심각하게 세포괴사를 일으켰으며, 저온은 초기에는 세포괴사를 유발하였으나 12시간 경과후에는 세포분열이 더욱 활발하게 일어나 세포의 생명력을 연장시켜주었다. 결국 이 실험에서는 전이성 암세포를 제거하는 방법으로는 고은이 가장 효과적이며 유용함을 알 수 있었다.

• Applied Microscopy
• /
• 제38권3호
• /
• pp.275-278
• /
• 2008

Electron tomography (ET) is an electron microscopic technique for obtaining a 3-D image from any electron microscopy specimen and its application in biomedical science has been increased thanks to development of electron microscopy and related technologies during the last decade. There are few researches on ET in Korea during this period. Although the importance of ET has been recognized recently by many researchers, initial approach to electron tomographic research is not easy for beginners. The 4th International Congress on Electron Tomography (4 ICET) was held on Nov $5{\sim}8$, 2006, at San Diego. The program dealt instrumentation, reconstruction algorithm, visualization/quantitative analysis and electron tomographic presentation of biological specimen and nano particles. 1 have summarized oral presentations and analyzed the posters presented on the meeting. Cryo-electron microscopic system was popular system for ET and followed conventional transmission electron microscopic system. Cultured cell line and tissue were most popular specimens analyzed and microorganisms including bacteria and virus also constituted important specimens. This analysis provides a current state of art in ET research and a guide line for practical application of ET and further research strategies.

• Imaging Science in Dentistry
• /
• 제36권2호
• /
• pp.89-94
• /
• 2006

Purpose : To evaluate clinical usefulness of facial soft tissue thickness measurement using 3D computed tomographic images. Materials and Methods : One cadaver that had sound facial soft tissues was chosen for the study. The cadaver was scanned with a Helical CT under following scanning protocols about slice thickness and table speed; 3 mm and 3 mm/sec, 5 mm and 5 mm/sec, 7 mm and 7 mm/sec. The acquired data were reconstructed 1.5, 2.5, 3.5 mm reconstruction interval respectively and the images were transferred to a personal computer. Using a program developed to measure facial soft tissue thickness in 3D image, the facial soft tissue thickness was measured. After the ten-time repeation of the measurement for ten times, repeated measure analysis of variance (ANOVA) was adopted to compare and analyze the measurements using the three scanning protocols. Comparison according to the areas was analyzed by Mann-Whitney test. Results : There were no statistically significant intraobserver differences in the measurements of the facial soft tissue thickness using the three scanning protocols (p>0.05). There were no statistically significant differences between measurements in the 3 mm slice thickness and those in the 5 mm, 7 mm slice thickness (p>0.05). There were statistical differences in the 14 of the total 30 measured points in the 5 mm slice thickness and 22 in the 7 mm slice thickness. Conclusion : The facial soft tissue thickness measurement using 3D images of 7 mm slice thickness is acceptable clinically, but those of 5 mm slice thickness is recommended for the more accurate measurement.

• Molecules and Cells
• /
• 제37권4호
• /
• pp.322-329
• /
• 2014

N-acetylglucosamine kinase (GlcNAc kinase or NAGK; EC 2.7.1.59) is highly expressed and plays a critical role in the development of dendrites in brain neurons. In this study, the authors conducted structure-function analysis to verify the previously proposed 3D model structure of GlcNAc/ATP-bound NAGK. Three point NAGK mutants with different substrate binding capacities and reaction velocities were produced. Wild-type (WT) NAGK showed strong substrate preference for GlcNAc. Conversion of Cys143, which does not make direct hydrogen bonds with GlcNAc, to Ser (i.e., C143S) had the least affect on the enzymatic activity of NAGK. Conversion of Asn36, which plays a role in domain closure by making a hydrogen bond with GlcNAc, to Ala (i.e., N36A) mildly reduced NAGK enzyme activity. Conversion of Asp107, which makes hydrogen bonds with GlcNAc and would act as a proton acceptor during nucleophilic attack on the ${\gamma}$-phosphate of ATP, to Ala (i.e., D107A), caused a total loss in enzyme activity. The overexpression of EGFP-tagged WT or any of the mutant NAGKs in rat hippocampal neurons (DIV 5-9) increased dendritic architectural complexity. Finally, the overexpression of the small, but not of the large, domain of NAGK resulted in dendrite degeneration. Our data show the effect of structure on the functional aspects of NAGK, and in particular, that the small domain of NAGK, and not its NAGK kinase activity, plays a critical role in the upregulation of dendritogenesis.