• The Journal of Korean Society for Radiation Therapy
• /
• v.17 no.2
• /
• pp.133-140
• /
• 2005

Purpose : This test is designed to identify the validity of treatment plan by implementing real-time dosimetry by means of dose that is absorbed into PTV and OAR when preparing doses of 3D and POP plans. Materials and Methods : In treatment. error can be calculated be comparing Exp. Dose with the actual dose, which has been converted from 'the reading value obtained by placing diode detector on the area to be measured'. Same test can be repeated using Alderson-Rando phantom. Results : Errors were found: A patient(POP plan): 197.6/199=-1.2%, B patient(3D-plan): 199.9/198.7=+0.6%, C patient: 196/200=-1.5%. In addition, considering the resulted value of measuring OAR besides target-dose for C patient showed 96/200, representing does of 47%, the purpose of protection was judged to be duly accomplished. Also it was acknowledged the resulted value of -3.7% met the targeted dose within the range of ${\pm}5%$. Conclusion : Aimed for identifying the usefulness of pre-treatment dose measurement using diode detector, this test was useful to evaluate the validity of curing because it resulted in the identification of category to be protected as well as t dose. Moreover, it is thought to have great advantage in ascertaining the dose of target, dose of which is not calculated yet. Similar to L-gram before treatment, this test is thought to be very effective so that it can bring great advantages in the aspects such as validity of curing method and post-treatment plan as well.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.27 no.4C
• /
• pp.371-379
• /
• 2002

In this paper, the MMIC SPST switches operating from DC to 3GHz were designed and implemented. Prior to the design of switches, the small and large-signal switch models were needed to predict switch performance accurately. The newly proposed small-signal switch model parameters were extracted from measured S-parameters using optimization technique with estimated initial values and boundary limits. In the extraction of large-signal switch model parameters, the current source was modeled by fitting empirical equations to measured DC data and the charge model was derived from extracted channel capacitances from measured S-parameters varying the drain-source voltage. To design basic series-shunt SPST switches and isolation-improved SPST switches, we applied this model to commercial microwave circuit simulator. The improved SPST switches exhibited 0.302dB insertion loss, 35.762dB isolation, 1.249 input VSWR, 1.254 output VSWR, and about 15.7dBm PldB with 0/-3V control voltages at 3GHz.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2020.06a
• /
• pp.310-310
• /
• 2020

자연하천에서 식생의 성장은 유속 및 수위 변화에 중요한 영향을 미치며, 따라서 식생으로 인한 흐름저항은 흐름과 유사이송 모델링을 위한 중요 매개 변수가 된다. 즉, 수치 모델을 활용함에 있어 식생의 흐름 저항을 정확하게 추정하는 것이 매우 중요하며, 보다 정확한 추정을 위해 실험 혹은 현장 데이터를 활용한 보정과정이 필수적으로 요구된다. 본 연구에서는 식생 패치를 포함한 인공 수로의 흐름 모의를 위해 실규모 실험 수로에서 측정된 유속 및 수위 데이터를 활용하여 모델보정을 수행하고자 한다. 이를 위해 공간 분포 별로 각기 다른 흐름 저항식의 적용이 가능하며, 식생 저항 공식을 포함하고 있는 Delft3D 모델을 활용하였다. 또한 실규모 수로에서의 유속 및 수위 데이터 수집을 위해 한국건설기술연구원 하천연구센터에서 실험을 수행하였다. 실험 구간의 길이는 약 120 m이고 하폭은 11 m이며, 국내 하천에서 보이는 식생패치의 유사한 형태를 재현하기 위해 하천 내 가장 많이 활착되어있는 버드나무와 유사한 형태의 인공식생을 제작하였다. 인공 식생은 지그재그로 배치되었으며, 식생의 전체 높이는 1.1 m이고, 각 패치 당 23그루의 인공 식생이 총 8개 패치에 식재되었다. 모의 조건은 상류단 유입 유량 2.805 ㎥/s, 하류단수위 98.764 m의 정류 조건을 적용하였다. 또한 식생 패치 구간에서의 흐름 저항 추정을 위해 Delft3D 모델 내에서 선택가능 한 Baptist의 비침수(Non-submerged)식을 적용하였으며, 항력계수 결정을 위해 1과 1.5를 적용하여 측정 수위와 비교하였다. Delft3D의 흐름 모의 결과, 항력계수 1.5를 적용했을 때, 측정 수위와 거의 일치하는 것으로 나타났으며, 항력계수 1.0을 적용했을 경우, 측정 수위에 비해 다소 낮게 모의되는 것으로 나타났다. 또한 항력계수 1.5인 경우 식생 패치 구간에서 평균 0.65 m/s의 유속이 발생하였다.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.3
• /
• pp.358-365
• /
• 2008

A differential-gain-controlled LNA is designed and implemented in 0.18 um CMOS technology for $3.1{\sim}4.8GHz$ UWB system. In high gain mode, measurements show a differential power gain of $14.1{\sim}15.8dB,\;13.3{\sim}15dB$, respectably, an input return loss higher then 10dB, an input IP3 of -19.3 dBm, a noise figure of $4.85{\sim}5.09dB$, while consuming only 19.8 mW of power from a 1.8V DC supply. In low gain mode, measurements show a differential power gain of $-6.1{\sim}-4.2dB,\;-7.6{\sim}-5.6dB$, respectably, an input return loss higher then 10dB, an input IP3 of -1.45 dBm, a noise figure of $8.8{\sim}10.3dB$, while consuming only 5.4mW of power from a 1.8V DC supply.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.3
• /
• pp.327-335
• /
• 2011

A study on the RCS of a self-manufactured active transponder, which has a manually adjustable RCS, for SAR(Synthetic Aperture Radar) external calibration and image analysis at X-band is presented in this paper. The RCS of the active transponder was comparably analyzed using the lab-test and the COSMO-SkyMed SAR system, and also precisely analyzed the difference between the adjusted and estimated RCSs. A maximum RCS of the designed and manufactured active transponder is 60 dBsm. The active transponders with 60 dBsm and the adjusted RCS of 40 dBsm were measured using the single target calibration technique(STCT) and 2D target scanning technique(2DTST). And the extracted RCS using power-spill integration technique in a SAR image was compared with the measured RCS of active transponder. The comparison results show that the measured and extracted RCSs are 59.7 dBsm, 40.2 dBsm and 57.3 dBsm, 39.2 dBsm, respectively.

• The Proceeding of the Korean Institute of Electromagnetic Engineering and Science
• /
• v.6 no.1
• /
• pp.28-36
• /
• 1995

In this paper, a design method of multiple n-way low loss power divider for x-band is propossed. To decrease loss, only two-stages of transmission lines are used with isolation resistors for match. Ex- perimental results for 3-way and 4-way power dividers have the divided power of 5.54~6.17dB and 6.76~7.37 dB, the return loss of more than 17dB and 12dB, and the isolation of more than 18dB and 10dB at center frequency, respectively, The measured results show good agreement with the theoretical analysis.

• Journal of the Korean Society of Radiology
• /
• v.16 no.7
• /
• pp.825-833
• /
• 2022

In 3D printing technology, materials that can be printed are increasing along with the development of material engineering, and materials that can be used in the field of radiation are also increasing. Therefore, depending on the composition and density of the materials used, the applied field can be different and applied, so the composition and characteristics of the materials must also be considered. In this study, 10 filaments with different properties were selected using a 3D printer of the FDM (Fused Deposition Modeling) method, and the brightness change of each filament was checked using a diagnostic X-ray generator, and the CT number was measured through CT. I wanted to find a material similar to bone. As a result, a material called silicon carbide was found, which has a similar brightness and CT number to bone. It is thought that further research will be presented as basic data for various studies with a density similar to that of human bones.

• Explosives and Blasting
• /
• v.38 no.2
• /
• pp.1-12
• /
• 2020

Digital Image Correlation is a well-established method for displacements, strains and shape measurements of engineering objects. Stereo-camera 3D Digital Image Correlation (3D-DIC) systems have been developed to match the specific requirements for measurements posed by material and mechanical industries. Although DIC method provides the capabilities of scaling a field-of-view(FOV), dimensions of Geotechnical structure objects in many cases are too big to be measured with DIC based on a single camera pair. It can be the most important issue with applying 3D DIC to the measurement of Geotechnical structures. In this paper, We were present stereo vision conditions in a 3D DIC system that can be measured for large FOV(30×20m) and high precisions(z-displacement 0.5mm) of the ground objects with Stereo-camera DIC systems.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2022.10a
• /
• pp.617-619
• /
• 2022

An embedded fiber-optic sensor was manufactured using 3D printing technology for distributed structural monitoring. Strain distribution of the embedded sensor was measured by the optical frequency domain reflectometry, and real-time data visualization for the embedded sensor model was demonstrated.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.34 no.4
• /
• pp.333-338
• /
• 2008

The evaluation for the visage volume was performed with human and dummy face using PRIMOS $body^{(R)}$. Three researchers measured the dummy face attached different volume of clay (6.6 mL, 13.2 mL, and 19.8 mL). It is identified that the high correlation between measured values and real volume ($R^2=0.99$). The percent (%) of relative standard deviation (RSD) of the data was shown below 10%. In Gage R&R analysis, the percent of contribution, the percent of study variation and distinct categories values were 0.78%, 8.85%, and 15% respectively. Therefore this method was regarded as the good standard condition in aspect of reproducibility and repetitiveness of data. The face volume variation was measured by PRIMOS $body^{(R)}$ on the face in participated 10 healthy Korean women volunteers. Subjects used the product once a day for two weeks as night sleeping pack. After application of the test products, the 3D image data of face were taken 1 and 2 weeks later. We found the face volume was significantly decreased after using products. In conclusion, this novel non-invasive technique was useful in measuring and visualizing alterations in face volume as a consequence of certain treatments. This system will provide a rapid and precise analysis of 3D topographical information for face.