• 한국세라믹학회지
• /
• 제34권5호
• /
• pp.535-543
• /
• 1997

The surface of SiC particles were partially oxidized to produce SiO2 layers on the SiC particles to prepare Al2O3/SiC composite by formation of mullite bonds between the grains of Al2O3 and SiC during sintering at 1$600^{\circ}C$. This process is considered to enable the sintering of Al2O3/SiC composite at lower temperature and also to relieve the stress, produced by thermal expansion mismatch between Al2O3 and SiC. In fact, Al2O3/SiC composite prepared by oxidation of SiC was observed to be more effectively sintered and densified at lower temperature. Maximum density, flexural strength and microhardness were obtained with 5.65 vol% of mullite content in Al2O3/SiC composite.

• 한국결정성장학회지
• /
• 제9권2호
• /
• pp.212-216
• /
• 1999

SiC(3C) 광다이오드는 p-형 Si 위에 tetramethylsilane (TMS)를 열분해아여 화학기상증착법으로 성장된 SiC(3C) 에피층을 성장하여 제작되었다. SiC(3C)의 전기적 특성은 홀 측정(Hall measurement) 및 전류-전압(I-V) 특성으로 조사되었다. SiC(3C) 에피층의 전도형은 n-형이었다. 저항성 접촉은 마스크 (shadow-mask)를 통해서 Al을 열증착하여 형성하였다. SiC(3C)광다이오드의 광학적 이득(photovoltaic detection)를 해석하기 위하여 SiC(3C) 에피층의 Spectral response (SR)를 전기적 변수(electrical parameter) 및 광다이오드의 기하학적 구조(geometric structure)를 고려하여 계산하였다. 적절히 선정된 변수들로부터 계산된 SR의 최대값은 550 nm에서 약 0.75이었고, 파장영역 400~600 nm 사이에서 청색 및 근자외선 광검지기로서 매우 유용하다.

• 한국결정성장학회지
• /
• 제9권1호
• /
• pp.39-42
• /
• 1999

N-도핑된 3C-SiC (N-SiC(3C))을 화학기상증착(CVD)으로 $1250^{\circ}C$에서 Si(111) 기판 위에 tetramethylsilane(TMS)를 열분해하여 성장하였다. 수송가스는 $H_{2}$이었고, N-SiC(3C) 에피층은 CVD로 성장되는 동안 $NH_{3}$에 의하여 n-형으로 도핑되었다. N-SiC(3C)의 물리적 특성은 적외선 분광(FTIR), X-선 회절(XRD), 라만 스펙트럼(Raman spectrum), 단면 투과전자영상(XTEM), Hall 측정 및 p/n 다이오드의 전압-진압(I-V) 특성에 의하여 조사되었다. N-도핑된 SiC(3C) 에피층의 전도형은 n-형이었고, 전도형은 $NH_{3}$를 사용한 N-dopant에 의하여 저온에서 잘 조절될 수 있다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 하계학술대회 논문집 Vol.8
• /
• pp.357-358
• /
• 2007

Raman spectra of poly (polycrystalline) 3C-SiC thin films, which were deposited on the oxidized Si substrate by APCVD, have been measured. They were used to study the mechanical characteristics of poly 3C-SiC grown in various temperatures. TO and LO modes of 2.0 m poly 3C-SiC grown at 1180 C occurred at 794.4 and $965.7\;cm^{-1}$. Their FWHMs (full width half maximum) were used to investigate the stress and the disorder of 3C-SiC. The broad FWHM can explain that the crystallinity of 3C-SiC grown at 1180 C becomes poly crystalline instead of the disordered crystal. The ratio of intensity $I_{(LO)}/I_{(TO)}$ 1.0 means that the crystal defect of 3C-SiC/$SiO_2$/Si is small. The biaxial stress of poly 3C-SiC was obtained as 428 MPa. In the interface of 3C-SiC/$SiO_2$, the phonon mode of C-O bonding appeared at $1122.6\;cm^{-1}$. The phonon modes related to D and G bands of C-C bonding were measured at 1355.8 and $1596.8\;cm^{-1}$ respectively.

• 한국세라믹학회지
• /
• 제37권2호
• /
• pp.152-157
• /
• 2000

Si3N4/SiC nanocomposite ceramics containing 5 wt%dispersed SiC particles were prepared by gas-pressure-sintering at 200$0^{\circ}C$ under nitrogen atmosphere. SiC particles with average sizes of 0.2 and 0.5${\mu}{\textrm}{m}$ were used, and the effect of the SiC particle size on the microstructure was investigated. The addition of SiC particles effectively suppressed the growth of the Si3N4 matrix grains. The effect of grain growth inhibition was higher in the nanocomposites dispersed with fine SiC. SiC particles were dispersed uniformly inside Si3N4 matrix grains and on grain boundaries. When the fine SiC particles were added, large fraction of the SiC particles was trapped inside the grains. On the other hand, when the large SiC particles were added, most of the SiC particles were located on grain boundaries. Typically, the fraction of SiC particles located at grain boundaries was higher in the specimen prepared from $\beta$-Si3N4 than in the specimen prepared from $\alpha$-Si3N4.

• 한국세라믹학회지
• /
• 제37권11호
• /
• pp.1114-1118
• /
• 2000

Ti 및 C 입자로 이루어진 다공질 성형체에 용융 Si의 침윤 및 반응으로 새로운 Ti$_3$SiC$_2$합성공정이 개발되었다. 용융 Si 침윤에 의한 Ti$_3$SiC$_2$합성공정에서는 이제까지 연구된 합성방법 보다 넓은 조성 범위에서 Ti$_3$SiC$_2$의 합성이 이루어졌다. 용융 Si을 활성 매질로 사용한 Ti$_3$SiC$_2$의 합성에서는 성형체 조성, 원료 입자 크기 및 침윤되는 용융 Si의 양에 따라 합성되는 상 및 각 합성상의 양이 다르게 나타났다. Ti:Si:C=3:1:6 조성을 제외한 모든 조성의 시편에서 Ti$_3$SiC$_2$상이 합성되었으며, 일부 조성을 제외한 모든 조성의 시편에서 Ti$_3$SiC$_2$, TiC 및 SiC가 함께 합성되었다. 작은 Ti 입자로 이루어진 성형체를 사용하여 합성한 시편에서 Ti$_3$SiC$_2$상의 합성이 용이하게 이루어졌으며, 성형체 조성 및 침윤되는 Si의 양이 화학양론적으로 Ti$_3$SiC$_2$에 근접한 조성을 갖는 시편에서 Ti$_3$SiC$_2$를 높은 수율로 합성할 수 있었다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 추계학술대회 논문집
• /
• pp.45-45
• /
• 2009

This paper describes the formation of porous 3C-SiC by anodization. 3C-SiC thin films were deposited on p-type Si(100) substrates by APCVD using HMDS (Hexamethyildisilane: $Si_2(CH_3)_6$). UV-LED(380 nm) was used as a light source. The surface morphology was observed by SEM and the pore size was increased with increase of current density. Pore diameter of 70 ~ 90 nm was achieved at 7.1 $mA/cm^2$ current density and 90 sec anodization time. FT-IR was conducted for chemical bonding of thin film and porous 3C-SiC. The Si-H bonding was observed in porous 3C-SiC around wavenumber 2100 $cm^{-1}$. PL shows the band gap enegry of thin film (2.5 eV) and porous 3C-SiC (2.7 eV).

• 한국전기전자재료학회논문지
• /
• 제20권2호
• /
• pp.156-161
• /
• 2007

This paper describes the characteristics of polycrystalline ${\beta}$ or 3C (cubic)-SiC (silicon carbide) thin films heteroepitaxailly grown on Si wafers with thermal oxide. In this work, the poly 3C-SiC film was deposited by APCVD (atmospheric pressure chemical vapor deposition) method using HMDS (hexamethyildisilane: $Si_{2}(CH_{3}_{6})$ single precursor. The deposition was performed under various conditions to determine the optimized growth conditions. The crystallinity of the 3C-SiC thin film was analyzed by XPS (X-ray photoelectron spectroscopy), XRD (X-ray diffraction) and FT-IR (fourier transform-infrared spectometers), respectively. The surface morphology was also observed by AFM (atomic force microscopy) and voids or dislocations between SiC and $SiO_{2}$ were measured by SEM (scanning electron microscope). Finally, depth profiling was invesigated by GDS (glow discharge spectrometer) for component ratios analysis of Si and C according to the grown 3C-SiC film thickness. From these results, the grown poly 3C-SiC thin film is very good crystalline quality, surface like mirror and low defect. Therfore, the poly 3C-SiC thin film is suitable for extreme environment, Bio and RF MEMS applications in conjunction with Si micromaching.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 하계학술대회 논문집 Vol.8
• /
• pp.333-334
• /
• 2007

This paper describes the characteristics of poly (polycrystalline) 3C-SiC grown on SiOz and AlN substrates, respectively. The crystalline quality of poly 3C-SiC was improved from resulting in decrease of FWHM (full width half maximum) of XRD by increasing the growth temperature. The minimum growth temperature of poly 3C-SiC was $1100^{\circ}C$. The surface chemical composition and the electron mobility of poly 3C-SiC grown on each substrate were investigated by XPS and Hall Effect, respectively. The chemical compositions of surface of poly 3C-SiC films grown on $SiO_2$ and AlN were not different. However, their electron mobilities were $7.65\;cm^2/V.s$ and $14.8\;cm^2/V.s$, respectively. Therefore, since the electron mobility of poly 3C-SiC films grown on AlN buffer layer was two times higher than that of 3C-SiC/$SiO_2$, a AlN film is a suitable material, as buffer layer, for the growth of poly 3C-SiC thin films with excellent properties for M/NEMS applications.

• 한국재료학회지
• /
• 제6권4호
• /
• pp.428-435
• /
• 1996

초미립 SiC분말과 SiC platelet을 2차성으로 Si3N4에 첨가하여 SiC/Si3N4 하이브리드 복합체를 가압소결로 제조한 후 2차상의 영향을 조사한 결과핫프레스법을 이용한 경우 SiC platelet은 Si3N4 기지 복합채의 치밀화를 저해하지 않고 초미립의 SiC 첨가는 Si3N4의 입성장을 효과적으로 억제하여 미세한 $\beta$-Si3N4의 grain을 형성함을 관찰하였다. 초미립 SiC첨가를 통한 복합체의 강도 증진은 상대적으로 $\beta$-Si3N4입자의 미세화에 의한 인성의 저하를 유도하나 SiC platelet을 첨가하여 급격한 강도 저하 없이 높은 인성을 갖는 하이브리드 복합체를 제조할 수 있었으며 SiC/Si3N4 하이브리드 복합체의 인성증진은 elongated $\beta$-Si3N4와 platelet SiC의 debonding에 의한 grain pull-out 영향임을 알 수 있었다.