• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.31 no.3B
• /
• pp.221-232
• /
• 2011

Applicability of three soil erosion models for burnt hillslopes was evaluated. The models were estimated with the data from plots established after tremendous wildfire occurred in the east coastal region. Soil erosion and surface runoff were simulated by the Water Erosion Prediction Project (WEPP) and the Revised Universal Soil Loss Equation (RUSLE) of application mode for disturbed forest areas and the Soil Erosion Model for Mountain Areas (SEMMA) developed for burnt hillslopes. Simulated sediment yield and surface runoff were compared with the measured those. In maximum value of sediment yield, three models was under-predicted and RUSLE and WEPP had difference of over two times. SEMMA showed the best model response coefficient, determination coefficient and the model efficiency. In application of models to the soil erosion according to the elapsed year after wildfire, all models were underestimated in initial stage disturbed by wildfire. Evaluation of models in this burnt hillslopes was shown the tends to under-predict soil erosion for larger measured values. Although a lot of sediment can be generated in small rainfall event as fine-grained soil of the high water repellency was exposed excessively right after wildfire, this under-prediction was shown that those models have a limit to estimate the weighted factors by wildfire.

• Journal of Broadcast Engineering
• /
• v.19 no.1
• /
• pp.31-43
• /
• 2014

A depth map is an important component for stereoscopic image generation. Since the depth map acquired from a depth camera has a low resolution, upsamling a low-resolution depth map to a high-resolution one has been studied past decades. Upsampling methods are evaluated by objective evaluation tools such as PSNR, Sharpness Degree, Blur Metric. As well, the subjective quality is compared using virtual views generated by DIBR (depth image based rendering). However, works on the analysis of the relation between depth map upsampling and stereoscopic images are relatively few. In this paper, we investigate the relationship between subjective evaluation of stereoscopic images and objective performance of upsampling methods using cross correlation and linear regression. Experimental results demonstrate that the correlation of edge PSNR and visual fatigue is the highest and the blur metric has lowest correlation. Further, from the linear regression, we found relative weights of objective measurements. Further we introduce a formulae that can estimate 3D performance of conventional or new upsampling methods.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.31 no.5
• /
• pp.227-234
• /
• 2018

Researches regarding measurement and control of the dynamic behavior of liquid such as sloshing have been actively on undertaken in various engineering fields. Liquid vibration is being measured in the study of tuned liquid dampers(TLDs), which attenuates wind motion of buildings even in building structures. To overcome the limitations of existing wave height measurement sensors, a method of measuring liquid vibration in a TLD using a laser Doppler vibrometer(LDV) and galvanometer scanner is proposed in this paper: the principle of measuring speed and displacement is discussed; a system of multi-point measurement with a single point of LDV according to the operating principles of the galvanometer scanner is established. 4-point liquid vibration on the TLD is measured, and the time domain data of each point is compared with the conventional video sensing data. It was confirmed that the waveform is transformed into the traveling wave and the standing wave. In addition, the data with measurement delay are cross-correlated to perform singular value decomposition. The natural frequencies and mode shapes are compared using theoretical and video sensing results.

• Elastomers and Composites
• /
• v.42 no.1
• /
• pp.47-54
• /
• 2007

Reaction kinetics of polyurethane elastomers (PU) were studied using dynamic DSC and TGA for three PU samples of general purpose (Sample A), high temperature cross-likable CASE purpose with MOCA (Sample B), and RT cross-likable CASE purpose grade (Sample C). From DSC results, sample with MOCA(Sample B) showed lower shift of peak temperature, while showing broader thermograms than those of general purpose grade (Sample A). On the other hand, RT cross-linkable PU grade (Sample C) showed an interesting double mode reaction patterns, i.e., a lower temperature reaction at about $70\;^{\circ}C$, and a higher temperature reaction in the range of $140{\sim}170\;^{\circ}C$, indicating that it requires 2-step reaction process in order to complete the reaction. Once the cross-linking reaction completed, however, TGA results showed that all the samples would be considered to have similar chemical structures, showing similar decomposition processes. Sample C, especially, had showed decomposition properties of both Sample A and Sample B. Formation activation energies calculated from Kissinger method showed 10.39, 65.85, 36.52(Low $T_p$) and 18.21(High $T_p$) kcal/mol, while decomposition activation energies were 31.94, 30.84, 24.16 kcal/mol, respectively.

• Analytical Science and Technology
• /
• v.31 no.6
• /
• pp.225-231
• /
• 2018

Benzoic acid, methyl paraben, and butyl paraben are preservatives that have been used in pharmaceutical, cosmetic, and food products. However, as their toxicities for human have been reported, many nations and organizations including Korea have established a regulation limit for thier usage of these preservatives in food products. The present study developed the isotope dilution liquid chromatography mass spectrometry method for accurate determination of three target preseratives in soysauce. In this study, the isotope dilution liquid chromatography mass spectrometry method was developed for accurate determination of three target preservatives in soy sauce. LC separation was optimized considering the pKa of benzoic acid which is lower than those of methyl and butyl parabens. A C18 column was used with 5 mM ammonium acetate and methanol as mobile phases. Mass spectrometry was operated in negative mode and selected reaction monitoring mode (SRM). Soy sauce sample was cleaned-up with C18 SPE cartridge for removing matrix inferences and color material. Optimized conditions and the method were validated with soy sauce reference materials for the analysis of food preservatives from Health Science Authority in Singapore. The measured values of benzoic acid, methyl and butyl paraben agreed well with reference values within their uncertainties.

• Progress in Medical Physics
• /
• v.17 no.1
• /
• pp.24-31
• /
• 2006

Automated analysis software was developed to measure the magnitude of the intrafractional and interfractional errors during breast radiation treatments. Error analysis results are important for determining suitable planning target volumes (PTV) prior to Implementing breast-conserving 3-D conformal radiation treatment (CRT). The electrical portal imaging device (EPID) used for this study was a Portal Vision LC250 liquid-filled ionization detector (fast frame-averaging mode, 1.4 frames per second, 256X256 pixels). Twelve patients were imaged for a minimum of 7 treatment days. During each treatment day, an average of 8 to 9 images per field were acquired (dose rate of 400 MU/minute). We developed automated image analysis software to quantitatively analyze 2,931 images (encompassing 720 measurements). Standard deviations ($\sigma$) of intrafractional (breathing motion) and intefractional (setup uncertainty) errors were calculated. The PTV margin to include the clinical target volume (CTV) with 95% confidence level was calculated as $2\;(1.96\;{\sigma})$. To compensate for intra-fractional error (mainly due to breathing motion) the required PTV margin ranged from 2 mm to 4 mm. However, PTV margins compensating for intefractional error ranged from 7 mm to 31 mm. The total average error observed for 12 patients was 17 mm. The intefractional setup error ranged from 2 to 15 times larger than intrafractional errors associated with breathing motion. Prior to 3-D conformal radiation treatment or IMRT breast treatment, the magnitude of setup errors must be measured and properly incorporated into the PTV. To reduce large PTVs for breast IMRT or 3-D CRT, an image-guided system would be extremely valuable, if not required. EPID systems should incorporate automated analysis software as described in this report to process and take advantage of the large numbers of EPID images available for error analysis which will help Individual clinics arrive at an appropriate PTV for their practice. Such systems can also provide valuable patient monitoring information with minimal effort.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.47 no.2
• /
• pp.21-31
• /
• 2010

This paper presents a design of PLL and SSCG for reducing the EMI effect at the electronic machinery and tools for DisplayPort application. This system is composed of the essential element of PLL and Charge-Pump2 and Reference Clock Divider to implement the SSCG operation. In this paper, 270MHz/162MHz dual-mode PLL that can provide 10-phase and 1.35GHz/810MHz PLL that can reduce the jitter are designed for 2.7Gbps/162Gbps DisplayPort application. The jitter can be reduced drastically by combining 270MHz/162MHz PLL with 2-stage 5 to 1 serializer and 1.35GHz PLL with 2 to 1 serializer. This paper propose the frequency divider topology which can share the divider between modes and guarantee the 50% duty ratio. And, the output current mismatch can be reduced by using the proposed charge-pump topology. It is implemented using 0.13 um CMOS process and die areas of 270MHz/162MHz PLL and 1.35GHz/810MHz PLL are $650um\;{\times}\;500um$ and $600um\;{\times}\;500um$, respectively. The VCO tuning range of 270 MHz/162 MHz PLL is 330 MHz and the phase noise is -114 dBc/Hz at 1 MHz offset. The measured SSCG down spread amplitude is 0.5% and modulation frequency is 31kHz. The total power consumption is 48mW.

• The Journal of the Korean bone and joint tumor society
• /
• v.9 no.1
• /
• pp.84-92
• /
• 2003

Purpose: To report two cases of bone tumors other than osteoid osteoma in the proximal femur and treated with percutaneous high frequency radioablation method. Cases: We reviewed two cases with intracortical chondroma and enchondroma in the femoral head retrospectively. The patient with intracortical chondroma was a thirty one year old woman and had suffered right hip pain of 1 year duration. The lesion was located in the head of right femur and treated with CT guided percutaneous high frequency radioablation after needle biopsy under general anesthesia. The symptom was gone immediately after the procedure and was discharged postop. 1 day. 15 months has passed without symptom recurrence. Second case having enchondroma, was 56 year old woman complaining of gluteal area pain for 3 months. Radiologic evaluation showed osteolytic lesion with sclerotic rim on the inferior portion of the left femoral head. She received a same therapy with CT guided radiofrequency ablation following needle biopsy. She reported dramatic pain relief after the procedure and was discharged postop. 1 day. No symptom has occurred for 3 months until now. Conclusion: We present 2 cases of bone tumor occurred in the hip joint area other than osteoid osteoma which were treated with CT guided radiofrequency ablation.

• The Korean Journal of Malacology
• /
• v.15 no.1
• /
• pp.31-39
• /
• 1999

This study was aimed to describe the population dynamics and secondary production of Tapes philppinarum on Chohwa and Toksan tidal flats in Kwangyang Bay, from June 1994 to July 1995. The size distributions in shell length showed bimodal patterns from June 1994 to April 1995. Thereafter the distribution changed to the passage of time, indicating an increase in shell length. The mean densities decreased gradually with month. Chohwa A sustained highestdensity, followed by Chohwa B, Toksan C, and Toksan D. The recruitment of new year class occurred first on the upper tidal flat, and then moved to the lower tidal flat. The mean biomass in flesh dry weight of each year class increased in spring just before the spawning period, and thereafter decreased progressively. Annual mean biomass wasrecorded as 170.7 g m$\^$-2/ at Chohwa A, 220.7 g m$\^$-2/ at Chohwa B, 21.8 g m$\^$-2/ at Toksan C, and 45.2 g m$\^$-2/ at toksan D. Annual productions of Ruditapes philippinarum were estimated as 259.72 g m$\^$-2/ yr$\_$-1/ at Chohwa A, 359.79 g m$\^$-2/ yr$\_$-1/ at Chohwa B, 45.02 g m$\^$-2/ yr$\_$-1/ at Toksan c, 68.88 g m$\^$-2/ yr$\_$-1/ at Toksan D. Annual productions were much higher on Chohwa tidal flat than those on Toksan tidal flat. While P:B ratio were higher on Toksan tidal flat as 1.70 than those on Chohwa tidal flat as 1.58. In conclusion, the Chohwa tidal flat showed higher biomass and producion of Ruditapes philippinarum, whereas the Toksan tidal flat showed higher P:B ratio. The total amount of potential food might influence on the density, biomass nad produciton, whereas the amount of food and space per individual might influence on the growth rate and P:B ratio.

• 한국공간정보시스템학회:학술대회논문집
• /
• 2007.06a
• /
• pp.268-272
• /
• 2007

현재 시행되고 있는 하천정비와 하도정비는 하천 흐름의 특성을 간과한 채 일괄적으로 진행되어 왔으며 그 결과로 하천의 인공화는 지금까지 계속되고 있다. 이에 따라 하천 및 하도의 물리, 화학, 생물에 미치는 영향은 심각하며, 그 동안 인위적인 하천교란의 요인과 하천교란에 따른 영향, 즉 하상변동, 외래종 식생 침입, 생태서식처 변화 등의 정량적 평가 기술의 수립은 매우 미흡한 상태이다. 뿐만 아니라 하천 교란 극복을 위한 저감기술, 복원기술 및 적응관리 기술 또한 체계적으로 정리되지 못하여 하천과 댐 관리당국이 어려움을 겪고 있다. 이러한 상황을 극복하기 위해서는 하천 교란에 대항하는 회복관리 기술 개발을 위한 교란 평가 기술이 필요하다. 따라서 본 연구에서는 항공사진 및 GIS기법을 이용하여 국내 주요하천의 원인별 교란실태를 조사하고 분석함으로써 하천교란 조사기술 개발에 응용할 수 있는 방안을 제시하고자 하였다. 분석을 위하여 댐 하류의 하천교란 및 적응현장 시범지역을 선정한 후 대상 지역의 항공사진을 GIS화하여 하천 교란 실태를 분석하는 데에 필요한 자료를 생성하였으며 생성된 자료를 바탕으로 하천의 평면 및 단면의 변화특성을 조사할 수 있었다. 또한 경년별 저수로 형태와 하천 중심선 비교 분석을 통하여 저수로의 이동 및 변화 양상을 규명해 낼 수 있었으며 그 결과 댐 하류지역에서 하도안정문제가 발생하였음을 확인할 수 있었다. 본 연구 결과를 바탕으로 보다 효율적인 하도안정문제에 관한 대책수립이 가능하리라 보며, 이를 위해서는 하천 교란 조사기술 개발에 대한 연구가 뒤따라야 할 것이다.과적임을 알 수 있었다. 실험 결과 본 기법으로 유휴시간에 프로세서를 저전력모드로 바꾸는 기존의 고전적인 전력 관리 기법보다 전체 시스템 전력 소모를 9% 더 절약할 수 있었다. 위성영상과 DEM 개발기술이 87% 이상의 점수를 받아 가장 시장성 및 활용성이 높은 기술로 평가되었으며, 초다분광영상에 대한 기술은 70%를 겨우 넘는 수준에서 평가가 되었다. 멀티센서 공간영상정보 통합처리 기술 개발은 다목적 실용위성의 보유, 국가 NGIS 사업의 결과물이 상당히 축척이 되어 있고, 라이다(LiDAR) 기술의 도입을 위한 환경이 조성되었기에 다른 국가에 비해 멀티센서 기술의 적용과 산업화가 가시화 될 수 있을 것으로 기대된다. 그러나 멀티센서 자료의 수급이 용이하지 못하고, 법 제도적인 한계, 시장의 성숙도가 기대이하라는 점 등의 한계를 노정하고 있다.a var. sieboldii 3. Pinus densiflora, Q. aliena, Q. acutissima, P. thunbergii, Q. acuta 4. Carpinus laxiflora, Camellia japonicas. C. tschonoskii community의 5개 그룹으로 나타났다. 하류의 부착돌말류는 상대적으로 양호한 수질을 가지고 있는 정점 1에서 다양한 생물상을, 탄천의 영향을 받는 정점 2는 상대적으로 수질이 악화되어 호오염성 종들이 높은 분포를 나타내고 있었다. 또한 부착돌말류 중 Cymbella minuta는 다른 부착돌말류에 비해 강한 오염지표성을 나타내고 있었다.p=0.000, $4.76{\pm}3.31$