• 대한기계학회논문집A
• /
• 제31권7호
• /
• pp.777-783
• /
• 2007

Since the performance of the circuit breaker mainly depends on the spring operating mechanism, the analysis of the spring operating mechanism is required. The spring, especially closing spring, stores the deformation energy due to the compression and then accelerates the big loads rapidly in the circuit breaker. To accurately carry out the kinematic and dynamic analysis of the circuit breaker, the precise modeling of the spring behavior is necessary. In this paper, the static stiffness of the spring is captured by using the tester. A simple mechanism similar to the spring operating mechanism was designed to generate the release motion of the spring. A high speed camera was used to capture the behavior of the spring. Three types of spring models such as a linear spring model, modal spring model, and nodal spring model are suggested and compared with the experimental results.

• 한국안전학회지
• /
• 제31권5호
• /
• pp.7-15
• /
• 2016

The purpose of this paper is to carry out Failure Modes and Effects Analysis (FMEA) and use criticality in order to determine risk priority number of the components of electric power installations in Engineering college building of D university. In risk priority number, GROUP A had 7 failure modes; more specifically, Transfomer had 4 modes, Filter(C)(1 mode), LA(1 mode), and CB(MCCB)(1 mode), and thus 4 components had failure modes. In terms of criticality, high-grade group a total of 16 failure modes, and 7 components-LA(1 mode), CB(MCCB)(1 mode), MOF(2 modes), PT(1 mode), Transformer(7 modes), Cable(3 modes), and Filter(C)(1 mode)-had failure modes. Comparison of risk priority number and criticality was made. The components which had high risk priority number and high criticality were Transformer, Filter(C), LA, and CB(MCCB). The components which had high criticality were MOF and cable. In particular, Transformer(RPN: 4 modes, Criticality: 7 modes) was chosen as an intensive management component.

• 한국전기전자재료학회논문지
• /
• 제15권10호
• /
• pp.858-864
• /
• 2002

Aging stabilities of the operating frequency of piezoelectric devices such as filter, oscillator and discriminator are very important. In this study it was studied aging stabilities of the length-extensional vibration mode of Pb(Zr$\^$y/O$_3$+ x[wt%]Cr$_2$Co$_3$ ceramics. PZT ceramics in morphotropic phase boundary have higher aging rates of k$\_$31/ and resonance frequency than those in tetragonal phase or rhombohedral phase. Thermal aging moves the composition with maximum aging rate to Zr-rich side in Cr$_2$O$_3$ not added PZT system. In the PZT system, aging rates of k$\_$31/ and resonance frequency for first 30 days are bigger than those for the following 90 days. Thermal aging decrease those for first 30 days. Aging rate of resonance frequency of the ceramics with x=0.1, y=0.53 and x=0.3, y=0.53 increased by thermal aging.

• Journal of Advanced Marine Engineering and Technology
• /
• 제31권1호
• /
• pp.34-43
• /
• 2007

As a method to improve the poor torque capacity on the continuously variable transmission(CVT), power splitted devices(PSD) reducing the power entering into the transmission has been considered. But this kind of PSD requires for the variator to be a large coverage of the speed ratio (CSR) Since the CSRs of the well-known push belt or the toroidal ones are not enough large, the power splitted CVTs (PSCVTs) using them should be made with multiple modes. inevitably adding the do9 clutches and the associated accessories. In this paper a PSCVT with single mode is conceptually designed A new continuously variable unit (CVU) consisting of the paired inner and outer spherical rotors is used. The CVU has large CSR and excellent compactness. As a PSD. a variable bridge (VB) using the Planetary gear units (PGUs) is considered because it has an upper bound on the power ratio. An optimal design to minimize the effective efficiency of the PSCVT is carried out. Through the performance analysis on the designed model, good expectation on the practicability in the heavy vehicle system is shown.

• 대한기계학회논문집A
• /
• 제31권1호
• /
• pp.97-104
• /
• 2007

Vibration analysis of a rigid body supported by in-parallel linear springs can be greatly simplified by utilizing the conditions for a plane of symmetry. The vibration modes of an oscillatory system having plane of symmetry are classified into the in-plane and out-of-plane modes. From the viewpoint of screw theory, they represent respectively the vibration axes perpendicular to the plane of symmetry and lying in the plane of symmetry. In this paper, the sets of orthogonal and mutually intersecting three springs are used as resilient support of a rigid body. The geometrical conditions for the system to have a plane of symmetry and diagonalized stiffness matrix are presented. From the orthogonality of the vibration modes with respect to the inertia matrix, the geometrical relation between the reaction wrenches and the vibration modes are derived. This geometrical relation is then used to get the cubic design equation for the design of out-of-plane modes. The numerical design example of engine mounts is presented in order to explain the suggested design technique.

• 대한기계학회논문집B
• /
• 제31권10호
• /
• pp.876-883
• /
• 2007

Numerical simulations are conducted for the design of a micro thermal mass air flow sensor (MAFS), which consists of a microfabricated heater and thermopiles on the silicon-nitride ($Si_3N_4$) thin membrane structure. It is important to find the proper locations of these thermal elements in the design of MAFS with improved sensitivity. Three heating modes of the micro-heater are considered: constant temperature, constant power and heating pulses. The analyses are focused on the membrane temperature profile near the sensing section. Considered are the practical flow velocities, ranging from 3 m/s to 35 m/s, and the corresponding Reynolds numbers from 1000 to 10000. The results show that one of optimum sensing locations is about $100{\mu}m$ away from the microheater. It is concluded that the heating mode and configurations of thermal elements are the main factors for the MAFS with higher sensitivity.

• Journal of Welding and Joining
• /
• 제31권5호
• /
• pp.64-70
• /
• 2013

The joining of Ti and SUS304 dissimilar metals is one of the effective measures to save rare metal. But Ti and SUS304 have differences in materials properties, and Ti and Fe intermetallic compounds such as TiFe and $TiFe_2$ are easily formed in weld fusion zone between Ti and SUS304. Nevertheless, in this study, full penetration lap dissimilar welding of Ti and SUS304 using single-mode fiber laser with ultra-high welding speed was tried, and it was found out that ultra-high welding speed could control the generation of intermetallic compound. To recognize the formation of intermetallic phase in the weld fusion zone and the compound zone of interface weld area were observed and analyzed using energy dispersive X-ray spectroscopy (EDX). And it was confirmed that the ultra-high welding speed could reduce amount of intermetallic compounds, but the intermetallic compounds were existed in the weld fusion zone under the all conditions.

• 한국광학회지
• /
• 제31권4호
• /
• pp.176-182
• /
• 2020

서브-미크론 주기의 미세한 회절 격자가 새겨진 도광판을 이용하여 빛을 수직으로 출사시켜 기존 방식에서 사용하는 집광용 프리즘 필름을 대체할 수 있는 가능성에 대하여 연구하였다. 시뮬레이션과 실험을 통해 최적 회절 격자 주기를 결정하였고, 입사되는 빛의 고도각과 방위각에 따라 회절 격자의 투과 모드 효율을 계산하였다. 또한, 회절에 의해 더 많은 빛을 추출할 수 있도록 도광판의 모양과 구성을 제안하여 고도각과 방향각을 최적화하는 두 가지 방식의 효과를 시뮬레이션으로 비교하였다. 광선 추적프로그램을 활용하여 회절 격자 각인 도광판의 휘도 각 분포를 계산하여 실제로 제작된 시제품의 위치별 휘도 각 분포와 비교하였다.

• 한국안전학회지
• /
• 제31권3호
• /
• pp.1-7
• /
• 2016

In this study, static and fatigue tests on the self-piercing riveted (SPR) joint were conducted using cross-shaped specimens with aluminum alloy (Al-5052) sheets. Mixed mode loading was achieved by changing the loading angles of 0, 45, and 90 degrees using a special fixture to evaluate the static and fatigue strengths of the SPR joints under mixed mode loading conditions. Simulations of the specimens at three loading angles were carried out using the finite element code ABAQUS. The fatigue specimens failed in an interfacial mode where a crack initiated at the upper sheet and propagated along the longitudinal direction and finally fractured Maximum principal stress, von-Mises effective stress failed to correlate the fatigue lifetimes at three loading angles. However, the equivalent stress intensity factor was found to be appropriate to correlate the fatigue lifetimes at three loading angles.

• 전력전자학회논문지
• /
• 제19권1호
• /
• pp.31-40
• /
• 2014

This paper describes an optimal configuration for multi-central inverters in a medium-voltage (MV) grid, which is suitable for large-scale photovoltaic (PV) power plants. We theoretically analyze a proposed common-mode equivalent model for problems associated with multi-central transformerless-type three-phase full bridge(3-FB) PV inverters employing two-winding MV transformers. We propose a synchronized PWM control strategy to effectively reduce the common-mode voltages that may simultaneously occur. In addition, we propose that the existing 3-FB topology may also have the configuration of a multi-central inverter with a two-winding MV transformer by making a simple circuit modification. Simulation and experimental results of three 350kW PV inverters in a multi-central configuration verify the effectiveness of the proposed synchronization control strategy. The modified transformerless-type 3-FB topology for a multi-central PV inverter configuration is verified using an experimental prototype of a 100kW PV inverter.