• Journal of Ocean Engineering and Technology
• /
• v.7 no.2
• /
• pp.131-140
• /
• 1993

To study the corrosion fatigue begavior of T.M.C.P. steel, the rotary bending fatigue test with the change of concentration of NaCl solution was carried out. Fatigue life in the corrosion environment is decreased markedly in comparision with that in the air. Fatigue limit in the air was about 225 MPa. In case of 3.5% NaCl solution fatigue life could be expressed as .sigma./sub f/=10,392 * (N/sub f/)/sup -o.2923 . According to the paris's rule, crack growth rates could be expressed as da/dN=2.62.*10/sup -7/ .DELTA. K/sup 1.09/(3.5% NaCl solution), da/dN=1.95 *10/sup -7 .DELTA. K/sup 1.05/(1% NaCl solution), da/dN=2.62 * 10/sup -7/.DELTA./sup 0.72/(0.01% NaCl solution) with da/dN expressed in mm/cycle and .DELTA.K in MPa.GAMMA.m. The crack growth rate in the corrosion environment was highest under 3.5% NaCl solution.

• 유체기계공업학회:학술대회논문집
• /
• 2000.12a
• /
• pp.373-378
• /
• 2000

The crevice corrosion of local corrosion occur when the gap exist on metal surface. This crevice corrosion happen to region such as flange of pipe, contact part of casing, under gasket and packing, between valve disk and seat of pump etc. Especially The crevice corrosion of mild steel(SS 400) get serious. This paper was studied on the crevice corrosion of SS 400 in fluid environment. In $0\%,\;2\%,\;3.5\%,\;5\% NaCl$ solution, the aspect of the crevice corrosion and polarization behavior under the crevice corrosion was investigated. And Weight loss rate of SS 400 with crevice and non-crevice was measured according to the NaCl concentration. The main results obtained are as follows : 1) Under crevice corrosion, the corrosion potential become less noble as the concentration of NaCl solution increased. 2) The current density under open circuit potential was high drained as concentration of NaCl solution increased by $3.5\%$ but the concentration increased over $3.5\%$, the current density was low drained. 3) The weight loss rate of SS 400 was increased as concentration of NaCl solution Increased by $3.5\%$, but the concentration increased over $3.5\%$, that of SS 400 was decreased. 4) Effect of oxygen for crevice corrosion in the concentration of $3.5\%$ NaCl solution become sensitive than that $0\%$ NaCl solution.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2001.05a
• /
• pp.152-157
• /
• 2001

This paper was studied on the characteristics of crevice corrosion prevention of SS 400 in marine environment. In NaCl solution, polarization behavior under the crevice corrosion was investigated. And Weight loss rate of SS 400 applied cathodic protection and non cathodic protection was measured according to the NaCl concentration. The main results obtained are as follows : The weight loss rate of Al-alloy galvanic anode was increased as the concentration of NaCl solution increased by 3.5% but the concentration increased over 3.5%, that of Al-alloy galvanic anode become decreased. The protective potential of SS 400 used Al-alloy galvanic anode becomes more cathodic polarization with increasing concentration of NaCl solution. Effects of oxygen on the weight loss rate of Al-alloy sacrificial anode for cathodic protection as the concentration of 3.5% NaCl solution become sensitive than that of 0% NaCl solution.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2000.11a
• /
• pp.1-6
• /
• 2000

This paper was studied on the crevice corrosion behavior of SS 400 in marine environment. In 0%, 2%, 3.5%, 5% NaCl solution, the aspect of the crevice corrosion and polarization behavior under the crevice corrosion was investigated. And Weight loss rate of SS 400 with crevice and non-crevice was measured according to the NaCl concentration. The main results obtained are as follows : 1) Under crevice corrosion, the corrosion potential become less noble as the concentration of NaCl solution increased. 2) The current density under open circuit potential was high drained as concentration of NaCl solution increased by 3.5% but the concentration increased over 3.5%, the current density was low drained. 3) The weight loss rate of SS400 was increased as concentration of NaCl solution increased by 3.5% but the concentration increased over 3.5%, that of SS400 was decreased.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.40 no.4
• /
• pp.481-486
• /
• 1995

The salt stress at seedling stage of winter barley was examined in different concentrations of NaCl containing 1/2 Hoagland solution. Fresh weight of seedling at 30 days after seeding was highest at 25mM of NaCl concentration containing 1/2 Hoagland solution but if the NaCl concentration was more than 50mM it began to decrease seriously. Water content in plant was decreased according to increase of NaCl concentration in 1/2 Hoagland solution, so physiological mechanism of NaCl in barley was different from saline plant. Stoma number per cm$^2$ of first leaf was higher than that of control in case of stressed by NaCl but in that case the leaf length was decreased so the number of stoma per first leaf was slightly decreased. Chloroplast shape was not changed by 75mM of high NaCl contained 1/2 Hoagland solution but cell division at root growing point was inhibited by 75mM of NaCl. As the result of salt stress mitochondria was ruined in structure and irregular solid was found to be transfered from the cytoplasm to the cell wall in root growing point.

• Corrosion Science and Technology
• /
• v.11 no.6
• /
• pp.232-241
• /
• 2012

This work focused on corrosion of carbon steel bolted GECM/Al parts in tap water and NaCl solutions. In tap water and NaCl solutions, open circuit potential of GECM and its potentials in a series of carbon steel bolt>Ti>Al became active. Regardless of test materials, open circuit potentials in tap water were noble, and increasing NaCl concentration, its potentials became active. Immersion test of single specimen showed that no corrosion occur in Ti and GECM. In tap water, carbon steel bolt didn't show red corrosion product and in chloride solutions, corrosion rate in 1% NaCl solution was greater than its rate in 3.5% NaCl solution and red corrosion product in 1% NaCl solution was earlier observed than that in 3.5% NaCl solution. It seems that this behavior would be related to zinc-coatings on the surface of carbon stee l bolt. On the other hand, aluminium was corroded in tap water and chloride solutions. Corrosion of aluminium in tap water was due to the presence of chloride ion in tap water by sterilizing process.

• Korean Journal of Materials Research
• /
• v.28 no.12
• /
• pp.738-747
• /
• 2018

For the aerospace structural application of high-strength 2xxx series aluminum alloys, stress corrosion cracking(SCC) behavior in aggressive environments needs to be well understood. In this study, the SCC sensitivities of 2024-T62, 2124-T851 and 2050-T84 alloys in a 3.5 % NaCl solution are measured using a constant load testing method without polarization and a slow strain rate test(SSRT) method at a strain rate of 10-6 /sec under a cathodic applied potential. When the specimens are exposed to a 3.5 % NaCl solution under a constant load for 10 days, the decrease in tensile ductility is negligible for 2124-T851 and 2050-T84 specimens, proving that T8 heat treatment is beneficial in improving the SCC resistance of 2xxx series aluminum alloys. The specimens are also susceptible to SCC in a hydrogen-generating environment at a slow strain rate of $10^{-6}/sec$ in a 3.5 % NaCl solution under a cathodic applied potential. Regardless of the test method, low impurity 2124-T851 and high Cu/Mg ratio 2050-T84 alloys are found to have relatively lower SCC sensitivity than 2024-T62. The SCC behavior of 2xxx series aluminum alloys in the 3.5 % NaCl solution is discussed based on fractographic and micrographic observations.

• Textile Coloration and Finishing
• /
• v.4 no.3
• /
• pp.65-73
• /
• 1992

To control the hydrolysis rate of PET fabric with NaOH, HCl and $CH_3$COOH(HAc), as regulating reagent, were added to the 0.5 M NaOH solution. The concentrations of acids in 0.5 M NaOH were varied. PET fabrics were treated with aqueous solutions of acids in 0.5 M NaOH under different conditions. The weight loss of PET fabric, the rate of hydrolysis, the apparent activation energy (E$_{\alpha}$), the handle value, the etched surface of treated PET fabric, and the effect of salts such as NaCl, $CH_3$COONa(NaAc), and NH$_4$Cl on the weight loss were discussed. Acids in the aqueous 0.5 M NaOH solution decreased the weight loss of PET fabric bacause of neutralization of OH- and the weight loss of PET fabrics treated with corresponding concentration of aqueous NaOH solution to the concentrations of the aqueous solutions of acids in 0.5 M NaOH was lower than that of PET fabrics treated with aqueous solutions of acids in 0.5 M NaOH. The addition of NaCl to aqueous NaOH solution accelerated the reaction of OH- with PET greatly, the addition of NaAc increased the weight loss slightly, but the addition of NH$_4$Cl decreased the weight loss. It was thought that the very remarkable result that NaCl in aqueous NaOH solution promoted the hydrolysis of PET with NaOH would contribute to the conservation of energy and NaOH in the weight loss finishing process of PET fabric. The etched surface and the handle value of treated PET fabric were independent of the difference in the kinds of acids and salts added.nd salts added.

• Corrosion Science and Technology
• /
• v.17 no.5
• /
• pp.225-230
• /
• 2018

The effects of birch sap, a possible natural corrosion inhibitor, on the corrosion behavior of steel in chloride solution were investigated. The corrosion rate was significantly reduced by the addition of 1~5 mL of birch sap to 500 mL of 3wt% NaCl or 3wt% $CaCl_2$ solution. A remarkable increase in the pitting potential in NaCl solution was observed by the addition of birch sap although it was almost constant in $CaCl_2$ solution. The corrosion rate of steel in both NaCl and $CaCl_2$ birch sap solution without addition of water was higher compared to that of aqueous solution without birch sap as the pH of the birch sap was 4.0. The presence of organic compounds like, fructose, galactose, glucose, and palmitic acid in the birch sap are thought to be adsorbed effectively on the metal surface, which provided corrosion protection. However, the inorganic elements including Na, Ca, K, Mg, Mn, S, etc. present in the birch sap exhibited no role in corrosion inhibition.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.41 no.6
• /
• pp.665-671
• /
• 1996

The salt stress at seedling stage of barley was examined in different concentrations of NaCl containing 1/2 Hoagland solution. Among the physiological factors electric conductivity and sodium content of cell sap outflow solution were increased according to the in-crease of NaCl concentration in 1/2 Hoagland solution but the total protein content of root cell sap outflow solution was decreased. Changing pattern of amino acids content in plant was divided into 3 groups which were increased, decreased or unchanged by NaCl concentration in solution. In normal condition, sugar content in plant was higher than potassium or sodium but if NaCl was added more than 25mM in 1/2 Hoagland solution, sodium was the highest. Potassium content in shoot was decreased as 67% of control at 100mM of NaCl containing solution and in root it was decreased as 8%. Sum of the potassium and sodium content in shoot was seriously increased in accordant with NaCl concentration in culture solution, but in root it was gradually decreased. Chlorophyll content per g fresh weight and photosynthetic ability per $\textrm{cm}^2$ in first leaf were not affected by NaCl concentration of 1/2 Hoagland solution but root activity was slightly decreased compared to control.