• Proceedings of the Korean Geotechical Society Conference
• /
• 2005.03a
• /
• pp.163-170
• /
• 2005

In this paper, the rock bolts, soil nails with filling grout and the micro-piling with injecting grout by pressure were applied for the stabilization of the cut slopes consisting of sedimentary rocks, igneous rocks and metamorphic rocks respectively. The field measurements and 3-D FEM analyses to find out mobilized tensile stresses of the grouted-reinforcing members installed in the drilled holes were executed on each site. With assuming the increments of the cohesive strength in the improved ground, the back analysis using direct calibration approach of changing the elastic modulus of the ground was used to find out the improved elastic modulus which yields the same tensile stresses from field measurements. The results of back analysis show that the elastic modulus of the improved ground were 4 to 6 times as large as the elastic modulus of original ground. Consequently, the design for slope reinforcement to be more rational, it is proposed that not only the improved cohesive strength is to be used in the incremental ranges on well-known previous proposed data, but also the increased elastic modulus which is about 5 times as large as the original elastic modulus is to be considered in design.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.22 no.2
• /
• pp.310-317
• /
• 2013

In this paper, the contact pressure of the wafer and polishing pad for final polishing process for 300 mm-wafer were investigated through numerical analysis using FEM tool, ANSYS. The distribution of the contact pressure is one of main parameters which affects on the flatness and surface roughness of polished wafers. Two types of polishing head, a hard type head with ceramic disk and a soft type head with air bag were considered. The effects of the deformation and initial shape of table on the contact pressure were also examined. Both heads and tables were modeled as 3D finite element model from solid model, and the material properties of polishing pads and rubber plate for the air-bag head were obtained from tensile tests. The contact pressure deviation on wafer surface was smaller with air bag head than hard type head even when the table had form errors such as convex or concave. From this 3D analysis, it could be concluded that the air-bag head has better uniformity of the contact pressure on wafer. Also, the effects of inner diameter of air bag and radial clearance between wafer and retainer were investigated as view point of contact pressure concentration on the edge of wafer.

• Ocean Systems Engineering
• /
• v.1 no.1
• /
• pp.73-93
• /
• 2011

Large deck openings of ultra large container ships reduce their torsional stiffness considerably and hydroelastic analysis for reliable structural design becomes an imperative. In the early design stage the beam model coupled with 3D hydrodynamic model is a rational choice. The modal superposition method is ordinary used for solving this complex problem. The advanced thin-walled girder theory, with shear influence on both bending and torsion, is applied for calculation of dry natural modes. It is shown that relatively short engine room structure of large container ships behaves as the open hold structure with increased torsional stiffness due to deck effect. Warping discontinuity at the joint of the closed and open segments is compensated by induced distortion. The effective torsional stiffness parameters based on an energy balance approach are determined. Estimation of distortion of transverse bulkheads, as a result of torsion and warping, is given. The procedure is illustrated in the case of a ship-like pontoon and checked by 3D FEM analysis. The obtained results encourage incorporation of the modified beam model of the short engine room structure in general beam model of ship hull for the need of hydroelastic analysis, where only the first few natural modes are of interest.

• Proceedings of the KSME Conference
• /
• 2004.11a
• /
• pp.148-153
• /
• 2004

This paper represents that parts of a large generator operating in 1000 MW are affected by centrifugal forces due to high-speed rotation in 3600 rpm and 3D FEM Analyses are required to obtained the structural reliability of the generator. From these results, one would know the weakest locations and the stress distributions. The fatigue life is calculated in order to grasp the remaining life of generator. 2D and 3D analyses are performed to calculate stresses of the generator rotor and the retaining ring. From 2D results, we find the SCF at the slot and sub-slot of the rotor. 3D analysis is applied at the end part of generator rotor, which represents complex geometry, and rotor and retaining ring shrink thermally. With these results, designers of rotor and retaining ring can compare with the results of design code and verify the stress distributions of generator rotor and retaining ring, and then calculate the remaining life from the low-cycle fatigue data.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.30 no.1
• /
• pp.31-37
• /
• 2017

In this paper, computation results of reducible modeling, stress recovery and energy release rate were compared with the results of VABS, Virtual Crack Closure Technique. The result of stress recovery analysis for 1-D model including the stiffness matrix is compared with stress results of three-dimensional 3-D FEM. Energy release rate of composite beam with longitudinal cracks is calculated and compare verifications of numerical analysis results of 3-D FEM and VABS. The procedure of calculating energy release rate through dimensional reduction and stress recovery is intended to be efficient and be utilized in the life-cycle of high-altitude uav's wing, wind blades and tilt rotor blade.

• Proceedings of the KIEE Conference
• /
• 2006.07b
• /
• pp.683-684
• /
• 2006

It is necessary to modify the state-of-the-art of speed control theory because of the phase asymmetry in the Linear Induction Motor (LIM)and for the constant speed control of mover using single vector control inverter system, it is important that primary stack is located in appropriated intervals in the 3D conveyer system using LIM. The dynamic characteristic analysis method of the vector controlled LIM using coupled FEM and control algorithm taking into account the movement is proposed. The focus of this paper is the analysis relative to selecting primary stack intervals in order to constant speed control in the 3D conveyer system using LIM.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2009.10a
• /
• pp.245-249
• /
• 2009

According to the increase of intelligent vehicles many automotive electric components are installed. The wire harness which connects those also increases. The crimping process for compressing the copper wire bundle into the terminal is a key process to assure the good quality of wire harness. For the case of inadequate forming condition many shape failures such as less-filling, over-filling are happen in the crimping process. Even though the quality of crimping shape is satisfactory the quality check for electrical resistance of wire harness is sometime not satisfied the qualification due to large variation of electrical resistance of wire harness under climate test. This large variation is thought to be related with the malfunction automotive electric system and caused by the internal stress of wire, which occurred during the crimping process. In this paper we develop the 3D-FEM simulation scheme and design methodology of optimum terminal shape. Also the effect of terminal shape on the residual stress is discussed.

• Proceedings of the KIEE Conference
• /
• 1998.07a
• /
• pp.325-327
• /
• 1998

Disk type single-phase switched reluctance motor which has an advantage of simple robust construction, simple control circuity, and low manufacturing cost has a specific property of axial flux machine and radial flux machine simultaneously. So, this DSPSRM has a complicated magnetic circuit and it is difficult to analyze characteristics of DSPSRM for design. In this paper, we used to analyze the effects of radial flux and axial flux simultaneously by 3D-finite element method. From the results of 3-D FEM, we obtained the approximated torque characteristics of DSPSRM. It's analysis results can be used in optimal design of DSPSRM considering the saturation.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2008.10a
• /
• pp.683-690
• /
• 2008

Steel-concrete composite columns are popular for superstructures of bridges, and the outside steel attached to the shaft increases the shaft resistance due to confining concrete. In this study, lateral resistance of steel-concrete composite drilled shafts was evaluated quantitatively based on numerical analysis when steel casings are used as structural elements like composite columns. Ultimate lateral resistance of composite drilled shafts with various diameters was numerically calculated through 3D finite element analysis. For that, elasto-plastic model with perfectly plasticity is involved to capture the ultimate load. A commercial FEM program, MIDAS-GTS, is used in this study. Real field conditions of the West Coast, Korea were considered to set up the ground conditions and pile lengths required for this parametric studies. Detailed characteristics of the stress and displacement distributions are evaluated for better understanding the mechanisms of the composite shaft behavior.

• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.1005-1006
• /
• 2007

This paper analyzed the characteristics of the claw pole permanent magnet(PM) stepping motor by using 3D Finite element method(FEM). In this motor, magnetization is occurred along the z-axis, therefore it is necessary to apply 3D FEM for analysis of the claw pole motor. A phase difference of the two stacks's detent torque is 180 degrees. When the center of a permanent magnet is identical with the middle of a pole, small detent torque is produced in order to cancel each of detent torques. However, there are construction errors which are a discrepancy between one and the other phase section in the manufacturing process, thus the detent torque is increased. Moreover, it is confirmed that the proportion of the detent torque is considerably arisen according to the error. Analysis of the construction error is studied by changing the error $0^{\circ}$ to $3^{\circ}$.