• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.30 no.3
• /
• pp.73-78
• /
• 2016

3phase induction motor consumes 40% of national electric power. so It is one of the most important electric device for the national power policy. The efficiency measurement is carried out by IEC standards. After the temperature rise test, It's difficult to measure the winding resistance immediately. because of inertia and power cut-off time. Therefore, IEC standards suggest the measurement time. But during the measurement time, the winding temperature cools down. It causes the value of winding resistance is variable. Several conditions which possibly occurred by the measurement time of IEC 60034-1 are suggested. and The efficiency evaluation of 3phase induction motors is carried out by IEC 60034-2-1 with the several conditions. As the results, we find out the winding resistance rapidly goes down within 15 sec. so It proves that the winding resistance should be measured within 15 sec. for the efficiency evaluating of 3phase induction motor.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.27 no.8
• /
• pp.510-515
• /
• 2014

Thin films of cubic $Na_{0.6}WO_3$, which is one of the sodium tungsten bronze, were fabricated by rf sputtering for the electrode applications in integrated sensors and actuators. A single-phase cubic $Na_{0.6}WO_3$ sputtering target of power type was prepared by conventional solid-state reaction. Thin films were deposited from the powder target, and the as-deposited films were amorphous, thus they annealed by tube furnace or RTP for crystallization. Thin films having cubic phase $Na_xWO_3$ were fabricated by the optimization of sputtering and post-annealing conditions, but single-phase cubic $Na_{0.6}WO_3$ thin films were not obtained. Although the films were not in single phase, they had good electrical conduction properties showing electrical resistivities of $10-4{\Omega}{\cdot}cm$ order.

• Journal of the Korean Ceramic Society
• /
• v.31 no.10
• /
• pp.1240-1246
• /
• 1994

While sintering the Pb(Mg1/3Nb2/3)O3-PbTiO3-BaTiO3 system through solid-reaction route, pyrochlore(Pb3Nb4O13) phase while reduces the dielectric constant is inevitably formed. Substitution of Pb(Mg1/3Nb2/3)O3 with PbTiO3 and BaTiO3 can retard the occurrence of pyrochlore phase. The perovskite solid-solution without containing pyrochlore phase can be obtained when we consolidated the materials consisting of PbTiO3 and BaTiO3 at 1200℃ for 2 hours. The sintered body composed of 0.8Pb(Mg1/3Nb2/3)O3-0.1PbTiO3-0.1BaTiO3 composition showed the diffused phase transition(DPT) phenomena and the maximum value of dielectric constant at 0℃ (Tc') with the value of 1.3×104.

• Analytical Science and Technology
• /
• v.11 no.4
• /
• pp.292-296
• /
• 1998

Normal phase or reversed phase liquid chromatographic separation of isoquinoline of heterocyclic compounds and structural isomers of external substituents, $COOCH_3$, CN and $CH_3$ has been carried out by using several different columns and various mobile phases. From this results, the order of elution of heterocyclic compounds appears to depend on the solvent effect with kinds of mobile phases. Retention mechanism of normal phase system for 2-methylindoline, 2-methylindole, benzoxazole and benzothiazole was also studied depending on adsorption strength between solute and stationary phase of column. However, retention factors of reversed phase system were found on hydrophobic interaction with solvophobic effect.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.8 no.3
• /
• pp.230-238
• /
• 2003

In this paper, Inverter drives adopting 2 phase space vector SRP-PWM (Separately Randomized Pulse Position PWM) with fixed switching frequency is proposed. The proposed 2 phase space vector SRP-PWM scheme is based on the 3 phase SRP-PWM. In the proposed SRP-PWM scheme, each of two phase pulses is located randomly in each switching interval. The experimental results show that the voltage and acoustic noise harmonics are spread to a wide band area. Also, the performance of the proposed 2 phase SRP-PWM and the conventional center aligned SVM are compared to each other. In result, the speed response is nearly similar to each other from the viewpoint of the v/f constant control.

• The Transactions of the Korean Institute of Electrical Engineers A
• /
• v.51 no.4
• /
• pp.169-174
• /
• 2002

The magnitude and phase of the compensating voltage in Dynamic Voltage Restorer (DVR) system depend on the voltage sag in the phases affected by the fault and on the influence of the zero sequence components. If the delta connection of the transformer is used, the zero sequence components do not appear on the load side. But nowadays, Y connected transformers with grounded neutral, that is 3-phase 4-wire system, are usually used. Therefore the zero-sequence components are occurred during faults. The zero-sequence components result in the high insulation costs and the asymmetry of the phase and magnitude of the terminal voltages. In this paper 3 phase 4 wire distribution system and 3 phase 3 wire system are analyzed and characteristics of voltage sag are presented. And this paper proposes the method that can mitigate the zero-sequence under the unbalance faults causing voltage sage and phase angle iumps.

• Journal of Powder Materials
• /
• v.11 no.2
• /
• pp.171-178
• /
• 2004

Effects of liquid phase and reinforcing particle morphology on the sintering of Al-6 wt％Cu-10 vol％ $Al_2O_3$ or SiC particles were studied in regards to densification, structure and transverse rupture properties. The Al-Cu liquid phase penetrated the boundaries between the aluminum matrix powders and the interfaces with reinforcing particles as well, indicating a good wettability to the powders. This enhanced the densification during sintering and the resulting strength and ductility. Since most of the copper added, however, was dissolved in the liquid phase and formed a brittle $CuAl_2$ phase upon cooling rather than alloyed with the aluminum matrix, the strengthening effect by the copper was not fully realized. Reinforcing particles of agglomerate type were found less suitable for the liquid phase sintering than solid type particles. $Al_2O_3$ and SiC particles protluced little difference on the sintering behavior but their size had a large effect. Repressing of the sintered composites increased density and bending properties but caused debonding at the matrix-particle interfaces and also fracturing of the particles.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.11 no.4
• /
• pp.307-312
• /
• 2006

This paper proposes the SRM drive system, which accurately estimates the phase currents from the DC-link current to drive SRM instead of detecting the three-phase currents. In addition, the detecting circuit of DC-link current is also proposed to increase the resolution and decrease the off-set influence. Comparing with the general drive system based on the phase current, it is verified through the experiments that the proposed SRM drive system based on the DC-link current has the good performance in steady-state response of the speed control. Using the DC-link current, all of the 3-phase currents can be easily estimated for driving the SRM.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.52 no.5
• /
• pp.221-229
• /
• 2003

This paper suggests a control algorithm of 3-phase 3-wire series active power filter. This suggested algorithm can compensate source harmonics and reactive power in 3-phase 3-wire power distribution systems. These harmonics are generated by nonlinear loads such as diode rectifiers and thyristor converters. This control algorithm extracts a compensation voltage reference from performance function without phase transformation. Therefore, this control algorithm is simpler than any other conventional control algorithms. 3-phase 3-wire series active power filters which have a harmonic voltage source and a harmonic current source are manufactured and experiments are carried out to verify the effectiveness of suggested control algorithm.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1998.11a
• /
• pp.281-285
• /
• 1998

The microstructure and conduction characteristics of ZnO varistor fabricated in the range of 0.0 ~ 4.0mol% $Y_20_3$ were investigated. With increasing$Y_20_3$ content, distribution of spinel phase decreased, whereas Y-rich phase segregated to the nodal point increased, as a result, the average grain size decreased in the range of $20.0 ~ 4.8{\mu}m$. $Y_20_3$ content showing relatively good conduction characteristics was l.Omol%, then nonlinear exponent and leakage current was 55.3, 0.66mA.respectively.