• Journal of Institute of Control, Robotics and Systems
• /
• v.21 no.11
• /
• pp.1027-1033
• /
• 2015

For the attitude control of spacecraft, two variable-speed control moment gyros are proposed as main actuators in the article. Since a variable-speed control moment gyro (VSCMG) makes two control torques (gyroscopic torque and reaction torque), two VSCMGs are sufficient for controlling 3-axes attitude. Additionally, there are no singular conditions for two non-parallel VSCMGs. Since gyroscopic torque is usually much greater than reaction torque, the control performances of approximately 3 axes may not be the same. However, several missions can be accomplished by controlling two axes. For such missions, a selective axes control method is proposed. The method selects two axes for a certain task and controls the attitude of the selected axes. For the remaining axis, angular speed is controlled for stabilization. A hardware-in-the-loop simulation has been used to test VSCMG modules and to verify the proposed method. Two VSCMGs can be alternative actuators for small satellites.

• Proceedings of the KIEE Conference
• /
• 2001.07d
• /
• pp.2329-2331
• /
• 2001

In this paper, were developed the 3 axes attitude control sensor system to control and monitoring the moving object. The proposed sensor system has been studied in Japan, America for a year ago. But it is high expensive and has a difficulty in application. To overcome these problems, proposed the 3 axes attitude control sensor system is low cost and easily applied. Proposed sensor system is equipped with the 3 gyro sensors, 2 tilt sensors and 3 MR sensors using 80C51 microprocessor for signal processing. It's output value transmit at long distance using RS232 serial communication protocol. We expect this system shall have a good performances in many applications of control and monitoring the moving object.

• Journal of Astronomy and Space Sciences
• /
• v.29 no.4
• /
• pp.389-395
• /
• 2012

The problem of spacecraft attitude control is solved using an adaptive neuro-fuzzy inference system (ANFIS). An ANFIS produces a control signal for one of the three axes of a spacecraft's body frame, so in total three ANFISs are constructed for 3-axis attitude control. The fuzzy inference system of the ANFIS is initialized using a subtractive clustering method. The ANFIS is trained by a hybrid learning algorithm using the data obtained from attitude control simulations using state-dependent Riccati equation controller. The training data set for each axis is composed of state errors for 3 axes (roll, pitch, and yaw) and a control signal for one of the 3 axes. The stability region of the ANFIS controller is estimated numerically based on Lyapunov stability theory using a numerical method to calculate Jacobian matrix. To measure the performance of the ANFIS controller, root mean square error and correlation factor are used as performance indicators. The performance is tested on two ANFIS controllers trained in different conditions. The test results show that the performance indicators are proper in the sense that the ANFIS controller with the larger stability region provides better performance according to the performance indicators.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.04a
• /
• pp.179-182
• /
• 2011

A practical application of flight-axes/attitude control thrusters to the space launch vehicle and their design development localization are investigated and analyzed. Hydrazine thrusters are mostly used in a final stage of space launch vehicles on account of its higher specific impulse and reliability necessary for the precise attitude control attaining the orbit insertion with higher accuracy.

• Aerospace Engineering and Technology
• /
• v.13 no.1
• /
• pp.44-54
• /
• 2014

This paper suggests two kinds of reaction control system command generation methods for upper stage attitude control of launch vehicles. The reaction control system is assumed to consist of two sets of three nozzles. One operation technology is based on mixed attitude error functions, and the other is based on command mixing functions. Both are compared via simulations. The simulation results show that the latter is comparatively preferable in terms of interference among control axes, independency of controller design and analysis among axes, and prediction of flight performance of each control axis.

• Aerospace Engineering and Technology
• /
• v.12 no.1
• /
• pp.189-199
• /
• 2013

This paper summarizes results of second stage attitude control of KSLV-I third flight test. The results show that three axes attitude control at coasting phases of KSLV-I was successfully accomplished by the reaction control system, and pitch and yaw attitude control at thrusting phase where second stage kick motor burns was also normally accomplished by using the thrust vector control system. It is verified that the second stage controller performed successfully for all flight phases regardless of some disturbances due to mass center offset, slag effects, and residual thrust of kick motor. These results may provide an important basis in enhancing domestic technology level of attitude control of launch vehicle.

• 제어로봇시스템학회:학술대회논문집
• /
• 2001.10a
• /
• pp.62.3-62
• /
• 2001

The predictive control is one of the nonlinear three-axis rotation methods. The desired trace of a satellite is pre-determined, and the control inputs are designed so that the satellite follows the ´predictive´ trace. The predictive control has been adapted to the research for the three-axis attitude control. In that case, the control variables are the quaternion represented the angular rates and attitude angles of the body about the three-axes. The objective of this paper is to propose to design a predictive controller for the three-axis attitude control under external disturbances. In order to do that, this paper proposes how to construct a predictive control law including disturbances and to discern them. The basic algorithm of the existent predictive control is partially modified, and the presumption and modeling of disturbances are performed ...

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.19 no.3
• /
• pp.505-514
• /
• 1994

Koreasat spacecraft requires accurate and reliable attitude control to provide beam pointing for tenyear long communication and direction broadcasting services. This paper describes the detailed design and performance of an on-orbit normal mode attitude control subsystem for the spacecraft. Koreasat used a momentum wheel which has nominal momentum 475in-1b sec(547.6cm-kg sec) aligned with the pitch axis to control pitch attitude and provide gyroscopic stiffness in roll/yaw plane and used a 300 atm magnetic torquer to control the roll and yaw attitudes. An Earth Sensor Assembly (ESA) is used to provide pitch and roll information for the on-board micropocessor. The roll/yaw control used bang-off-bang control and while pitch axis control used proportional and integral control law. Control system errors during the operational normal mode are 0.03 deg, 0.1 deg and 0.01 deg in roll, yaw and pitch axes, respectively. Current attitude control system provides adequate control performances to capture initial attitude errors and spacecraft nutation.

• Bulletin of the Korean Space Science Society
• /
• 2008.10a
• /
• pp.36.3-36.3
• /
• 2008

KARI (Korea Aerospace Research Institute) is going to launch a Communication, Ocean and Meteorological Satellite (COMS) at summer of 2009. It will be first thing to be developed for a geostationary satellite through domestic technology. Of course, KARI has performed this development program with EADS Astrium in France since 2005. COMS has the non-symmetric configuration that the solar array is only attached on the south panel. Due to the configuration, momentum of satellite will be rapidly accumulated induced by solar pressure and then 3 wheels of large momentum are located on roll-yaw plane for attitude control. Therefore, to prevent the saturation of wheel momentum, wheel off-loading will be performed two times per day during 10 minutes for each one. At the moment, translation movement on 3-axes direction appears because of using thrusters. In this paper, strategy of the wheel off-loading and triaxiality which is the translation effect on 3-axes are introduced. Consequently, the result of optimized triaxiality considering the wheel off-loading strategy is summarized.

• International Journal of Aeronautical and Space Sciences
• /
• v.11 no.3
• /
• pp.167-174
• /
• 2010

The design, dynamics, and control allocation of tri-rotor unmanned aerial vehicles (UAVs) are introduced in this paper. A trirotor UAV has three rotor axes that are equidistant from its center of gravity. Two designs of tri-rotor UAV are introduced in this paper. The single tri-rotor UAV has a servo-motor that is installed on one of the three rotors, which enables rapid control of its motion and its various attitude changes-unlike a quad-rotor UAV that depends only on the angular velocities of four rotors for control. The other design is called 'coaxial tri-rotor UAV,' which has two rotors installed on each rotor axis. Since the tri-rotor type of UAV has the yawing problem induced from an unpaired rotor's reaction torque, it is necessary to derive accurate dynamic and design control logic for both single and coaxial tri-rotors. For that reason, a control strategy is proposed for each type of tri-rotor, and nonlinear simulations of the altitude, Euler angle, and angular velocity responses are conducted by using a classical proportional-integral-derivative controller. Simulation results show that the proposed control strategies are appropriate for the control of single and coaxial tri-rotor UAVs.