• Journal of the Korea Concrete Institute
• /
• v.20 no.3
• /
• pp.317-323
• /
• 2008

In the current study, A model for the flow analysis of fresh and highly flowable concrete has been developed using a particle method, the moving particle semi-implicit (MPS) method. The phenomena on the flow of concrete has been considered as a visco-plastic flow problem, and the basic governing equation of concrete particle dynamics has been based on the Navier-Stokes equation in Lagrangian form and the conservation of mass. In order to formulate a visco-plastic flow constitutive law of fresh concrete, concrete is modeled as a highly viscous material in the state of non-flow and as a visco-plastic material in the state of flow after reaching the yield stress of fresh concrete. A flow test of fresh concrete in the L-box was simulated and the predicted flow was well matched with the experimental result. The developed method was well showed the flow motion of concrete particles because it was formulated to be based on the motion of visco-plastic fluid dynamics.

• Journal of the Korea Society for Simulation
• /
• v.28 no.3
• /
• pp.83-89
• /
• 2019

This research describes quantitative effects of initial dispersion conditions upon the dispersion randomness of Magnus rotor bomblets. Ratios of the missile spin rate to the missile velocity, a, flight path angles, ${\gamma}$ and altitudes, h, were changed to investigate their effects on dispersion randomness. Dispersion was analyzed through calculation of 6 degree of freedom motion equation with aerodynamic coefficients from wind tunnel experiments. In order to analyze the randomness, regression analysis is adopted to calculate the coefficient of determination. The optimized ratio of the missile spin rate to the missile velocity and flight path angle were obtained and the dispersion altitudes had more effect on the dispersion diameter and had less effect on dispersion than other parameters.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.17 no.3
• /
• pp.110-118
• /
• 2003

Spacer dampers maintain the constant gaps between each conductor in a bundle conductor-transmission line, and are installed at proper intervals to keep a line from all sorts of damages derived from the vibration energy caused by mechanical or electrical external factors. It is most important to embody a technology which considers difficulties of maintenance and repair, and has optimum elements in order to prevent accidents such as destruction by fire or the snapping of a wire by the effect of vibration phenomenon coming from transmission lint In the resent thesis, therefore, the analysis of vibratory characteristics of spacer damper is set up by analytical methods such as the analysis of conductor motion's governing equation, the equation of spacer damper's motion, spacer damper-fastened wire's motion in a span and the numerical analysis of finite difference method. Furthermore, the installation distance between spacer dampers was scrutinized by simulations of various vibration phenomena which change at any time as actual conditions do, and hereafter difference method. Furthermore, the installation distance between spacer dampers was scrutinized by simulations of various vibration phenomena which change at any time as actual conditions do, and hereafter we will be able to analyze all kinds of vibration phenomena coming from a boltless spacer damper with 6 bundle conductor for 765kV transmission line based on new analytical methods.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1994.10a
• /
• pp.116-120
• /
• 1994

최근 항공우주 및 생산자동화 분야의 급격한 발달에 따라 정밀도와 효율성을 향상시키기 위해 저중량, 고강도 구조물이 요구된다. 그러나 경량화 추세로 인해 수반되는 구조물의 유연성 증가로 외력에 대한 구조응답의 진폭이 커지고 구조물의 피로 수명이 단축되어 매우 위험한 상황에 이를 수 있다. 이런 바람직하지 않은 진동현상을 제어하기 위해 여러 제어이론을 응용한 진동억제시스템의 연구가 활발하며, 신소재인 압전재료의 개발로 새로운 방향이 제시되고 있다. 압전재료는 유연한 구조물에 부착되어 압전재료의 수축, 팽창 운동에 의해 발생된 에너지를 부착된 구조물에서의 제어력으로 사용되어, 진동 혹은 자세 및 형상 제어에 활용되고 있다. 압전재료에 대한 연구로는 Crawley, de Luis3가 보의 표면 혹은 내부에 압전세라믹을 부착하여 액튜에이터로 사용하는 경우 집중모멘트를 가하는 역할을 함을 밝혔고, Hanagud, obal은 압전재료를 센서와 액튜에이터로 사용해 복합재료 보에 대한 최적 진동제어 알고리즘을 개발, 그 성능에 대한 효과를 조사하였고 임의의 위치에 부착된 센서 및 액튜에이터를 고려한 복합재료 보의 운동방정식을 유한요소법을 이용 유도하였으며 변위율 피드백(rate feedback)과 모달피드백(modal feedback) 제어기를 적용하여 진동제어 효과를 고찰하였다. 그리고 Tomas, James, Hubbard는 압전필름을 액튜에이터로 사용해 복합재료 보에 Liapunov 제어기와 변위율 피드백 제어기를 사용하여 능동감쇠기를 설계하였고, Lee, Chaing, Sullivan은 압전필름을 센서와 액튜에이터로 사용해 평판에 변위율 피드백 제어기를 적용한 능동감쇠기를 설계하고 실험적으로 수행하였다. Base가 백색잡음가진을 지속적으로 받을 때 보끝의 움직임이 최소가 되도록 제어하고자 연구를 수행 중인 바 그 결과로소 본 논문에서는 적용시켰고 F-P-K 방정식을 이용해 확률영역으로 변환하여 LQR 제어기와 pole allocation 제어기를 시스템에 적용시켜 우수한 특성을 갖음을 제어 시뮬레이션의 결과를 통해 입증하였다.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.4 no.3
• /
• pp.53-61
• /
• 1984

A nonlinear formulation of a beam finite element(NB6) on the total Lagrangian mode for the geometrically nonlinear analysis of two-dimensional elastic framed structures is presented. The NB6 beam element has been degenerated from the three-dimensional continuum by introducing the deep beam assumptions and consists of three reference nodes and three relative nodes. The element characteristics are derived by discretizing the beam equations of motion using the Galerkin weighted residual method and are reduced-integrated repeatedly for each loading step by the Newton-Raphson iteration techpique. Several numerical examples are given to demonstrate the accuracy and versatility of the proposed nonlinear NB6 beam element.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.37 no.10
• /
• pp.998-1001
• /
• 2009

This paper shows that the conventional proportional navigation guidance(PNG) law with a constant navigation gain is an optimal solution strictly also when the velocity is varying during engagement. Especially, PNG with navigation constant, 3, is an optimal solution minimizing a closing velocity weighted induced-drag. While most of previous studies on optimality of PNG were relied on the linear formulation and the constant speed assumption, this study presents more general analysis results on optimality of PNG based on the nonlinear formulation and the time-varying velocity assumption.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.7 no.1
• /
• pp.65-73
• /
• 1987

An efficient plate bending finite element has been developed using higher-order inplane displacement profiles of the plate. The 6-noded, 21-d.o.f. triangular element including shear deformation effect has been derived from the plate-like continuum by the Galerkin's weighted residual method. Square plate examples were tested with selected element meshes and several aspect ratios for their static behavior under uniformly distributed load. The result of the example tests indicated consistently good performance of the present higher-order plate bending element in comparison with the thin and thick plate solution and other existing finite element solutions.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.17 no.3
• /
• pp.138-148
• /
• 2005

Dynamic response of floating structures such as floating body and floating bridges subject to wave load is to be calculated in frequency domain. Added mass coefficient, damping coefficient and wave exciting force are obtained numerically from frequency domain formulation of linear potential theory and boundary element method for a floating body which is partially submerged into water and subjected to wave force. Next, the equation of motion for the dynamic behavior of a floating structure which is supported by the floating bodies and modeled with finite elements is written in frequency domain. hker a hemisphere is analyzed and compared with the published references as examples of floating bodies, the hydrodynamic coefficients for a pontoon type floating body which supports a floating bridge are determined. The dynamic response of the floating bridge subject to design wave load can be solved using the coefficients obtained for the pontoons and the results are plotted in the frequency domain. It can be seen from the example analysis that although the peak frequency of the incoming wave spectrum is near the natural frequency of the bridge, the response of the bridge is not amplified due to the effect that the peak frequency of wave exciting force is away from the natural frequency of the bridge.

• Journal of Ocean Engineering and Technology
• /
• v.16 no.3
• /
• pp.19-27
• /
• 2002

The motion of a floating OWC chamber in waves is studied taking account of fluctuating air pressure in the air chamber. An atmospheric pressure drop occurs across the upper opening of the chamber which causes not only hydrodynamic but also pneumatic added mass and damping forces to the floating chamber. A velocity potential in the water due to the free surface oscillating pressure patch is added to the conventional radiation-diffraction potential problem. the potential problem inside the chamber is formulated by making use of the Green integral equation associated with the Rankine Green function wile the outer problem with the Kelvin Green function. The two integral equations are solved simultaneously by making use of a matching boundary condition at the lower opening of the chamber to the outer water region. The chamber motion in the frequency domain is calculated for various values of parameters related to the atmospheric pressure drop. The present methods can also be sued for the analysis of air-cushion vehicle motion as well as for the design of a floating OWC wave energy absorber.

• Journal of computational fluids engineering
• /
• v.19 no.2
• /
• pp.86-92
• /
• 2014

In this paper, prediction of separation trajectory for Two-stage-To-Orbit space launch vehicle has been numerically simulated by using an aerodynamic database based on steady state analysis. Aerodynamic database were obtained for matrix of longitudinal and vertical positions. The steady flow simulations around the launch vehicle have been made by using a 3-D RANS flow solver based on unstructured meshes. For this purpose, a vertex-centered finite-volume method was adopted to discretize inviscid and viscous fluxes. Roe's finite difference splitting was utilized to discretize the inviscid fluxes, and the viscous fluxes were computed based on central differencing. To validate this flow solver, calculations were made for the wind-tunnel experiment model of the LGBB TSTO vehicle configuration on steady state conditions. Aerodynamic database was constructed by using flow simulations based on test matrix from the wind-tunnel experiment. ANN(Artificial Neural Network) was applied to construct interpolation function among aerodynamic variables. Separation trajectory for TSTO launch vehicle was predicted from 6-DOF equation of motion based on the interpolated function. The result of present separation trajectory calculation was compared with the trajectory using experimental database. The predicted results for the separation trajectory shows fair agreement with reference[4] solution.