• 한국철도학회논문집
• /
• 제17권2호
• /
• pp.123-132
• /
• 2014

본 연구에서는 아스팔트 궤도구조개발을 목적으로, 노반용으로 배합설계된 19mm 밀입도 아스팔트 혼합물 시편을 제작한 다음 영구변형시험을 통해 영구변형 발생특성을 분석하였다. 영구변형시험결과와 AASHTO 2002 및 한국형 포장설계법(KPRP)에서 제시한 영구변형 예측식과 비교, 분석하였다. 현재까지 노반용 혼합물을 위한 영구변형 예측식이 개발된 바 없으므로 AASHTO 제안식을 이용하여 직결 및 유도상 아스팔트 궤도의 부설 시 발생 가능한 영구변형량을 추정하였다. 이를 위해 유한요소해석을 실시, 궤도 깊이 별 발생응력을 산출한 후 공용중 발생 가능한 영구변형량을 계산할 수 있었다. 예측된 소성침하량은 극미하여, 공용중 침하에 대한 내구성 확보가 가능한 것으로 판단되었다.

• 한국철도학회논문집
• /
• 제20권2호
• /
• pp.223-233
• /
• 2017

철도에 사용되고 있는 분기기는 중요한 시스템 중 하나이다. 분기기 시스템의 건전성은 철도운용 안정성에 매우 중요하다. 분기기 시스템을 진단하기 위하여, LVDT와 accelerometer를 분기기에 설치하였다. LVDT는 분기기에서 변위가 발생하는 부분에 설치하여, 분기기의 이동과 차량의 주행에서 발생되는 변위를 측정하였다. Accelerometers는 충격과 진동이 발생하는 부분에 설치하여 충격량과 진동을 측정하였다. 측정된 데이터를 이용하여 변수화를 위한 데이터를 추출하였으며, 이 변수들은 진단에 사용하였다. 진단 알고리즘은 확률분포와 인공신경망을 사용하였다. 변수화된 값이 확률분포를 이용하여 판단할 수 있으면 확률분포를 사용하였으며, 형태를 보고 판단할 필요가 있으면 인공신경망을 활용하였다. 본 논문에서는 정상적인 상태에서 데이터를 측정하여, 정상상태의 조건을 위한 학습을 수행하였다.

• 접착 및 계면
• /
• 제14권2호
• /
• pp.68-74
• /
• 2013

Acid group을 도입하여 접착 및 그립성이 향상된 casting 폴리우레탄을 합성하였다. 폴리우레탄의 그립 특성 및 접착 특성을 확인하였고, 접촉각 및 인장강도, 기계적 물성 등을 연구하였다. Acid 함량에 따른 특성들을 조사하기 위해 acid 함량별로 경화제를 제조하여 각각의 특성들을 연구하였다. Acid group을 도입함으로써 접착력 및 wet slip이 증가하는 것을 확인할 수 있었으며, 인장강도 및 마모 등 기계적 물성 또한 증가하는 것을 확인할 수 있었다. Acid 함량별로 물성을 측정한 결과 일정한 함량까지 기계적 물성은 증가하며, 일정 함량 이상에서는 기계적 물성 및 접착력이 감소하는 것을 확인할 수 있었다. Wet slip과 접촉각의 경우에는 acid group 도입에 의해 친수성이 증가함으로 acid 함량이 증가할수록 wet slip은 증가하며 접촉각의 경우에는 감소하는 것을 확인할 수 있었다.

• Restorative Dentistry and Endodontics
• /
• 제16권1호
• /
• pp.200-208
• /
• 1991

The purpose of this study was to observe shear bond strength of composite resin to dentin following surface treatment. Freshly extracted forty-eight sound human molars were used in this study. They were stored at $4^{\circ}C$ physiologic saline solution before experiment. The teeth was then mounted with self curing acrylic resin in brass mold. The buccal surfaces of the teeth were grinding approximately 1.5mm by means of water-irrigated grinding wheel to expose the flattened fresh dentin surfaces. The specimens were divided into 6 groups according to preparation and treatment procedures on dentin surfaces; Group 1: Untreated after preparation with No.301 diamond point Group 2: Treated with primer for 60 seconds after preparation with No.301 diamond point Group 3: Untreated after preparation with No.700 fissure carbide bur Group 4: Treated with primer for 60 seconds after preparation with No.700 fissure carbide bur Group 5: Untreated after grinding with 600 grit silicon carbide paper Group 6: Treated with primer for 60 seconds after grinding with 600 grit silicon carbide paper Light cure dental adhesive was applicated to each specimen. Silux plus(3M) was inserted then into polyethylene tube of 3mm diameter and 3mm height, and polymerized to dentin surface. All of the specimens were stored in distilled water at $35.6^{\circ}C$ for 24 hours prior to testing. The shear bond strength was measured using an Instron Universal Testing Machine. The results obtained from this study were as follows: 1. The shear bond strength to dentin was the highest in group II. 2. The shear bond strength to dentin was the lowest in group III. 3. There was no significant difference in shear bond strength to dentin according to preparation instrument. 4. The primer treatment group showed significantly greater shear bond strength than untreated group.

• 대한인간공학회지
• /
• 제30권5호
• /
• pp.659-669
• /
• 2011

Objective: The aim of this study is to suggest a package layout guideline for low-floor bus by interview with passengers and observations of their behavior. Background: Increasing attention has been introduced the low-floor bus to be more suitable for use by transportation handicapped. Complex issues are involved in providing comfortable services to all people. We are going to suggest package layout guidelines for more comfortable and suitable travel to all people. Method: The two times of survey and video observation sessions were conducted on low-floor buses in Seoul; (1) a finding of potential issues in the first session, (2) a confirming of issues from the last session. Results: The three of major issues were founded in this study; (1) difficulties in supporting body when standing, (2) difficulties in sitting on front wheel pan seat, (3) difficulties in passing through the aisle. Conclusion: There were clear differences between public and transportation handicapped in using some tools which are used for support body such as roof hand rails, side hand rails, and hand rail rings. Some of design problems were founded to improve from the perspective of ergonomics and universal design. Such differences and design guidelines have to be considered in bus design as well as commercial vehicle. Application: The proposed design guidelines can be used to development of low-floor bus and other public transportations.

• 한국가스학회지
• /
• 제21권2호
• /
• pp.26-31
• /
• 2017

이 논문은 디젤 자동차의 터보차저 시스템에 관련된 고장사례를 연구하기 위한 것이목적이다. 첫 번째 사례는 터보차저를 분해하여 확인한 결과 터보 휠의 파손으로 터빈이 손상되어 작동되지 않음으로 배기관 구멍이 막혀 가속이 되지 않는 것을 확인하였다. 터보차저 장착차량의 경우 높은 회전수에서는 엔진을 바로 정지시키게 되면 고온에 의한 터보의 고착현상이 발생될 수 있으므로 공회전 상태를 충분히 유지한 다음 시동을 끄도록 한다. 두 번째 사례는 터보차저를 작동시키는 VGT 액튜에이터의 로드가 고착되어 가속불량 현상이 발생된 것으로 확인되었다. 세 번째 사례는 알터네이터(Alternator) 저항과 인터쿨로 팬 릴레이 커넥터 오조립으로 인해 주행 중 출력부족 현상이 발생한 것을 확인하였다. 따라서, 터보차저 시스템의 철저한 관리를 통해 고장이 발생하지 않도록 하여야 한다.

• 대한조선학회지
• /
• 제9권2호
• /
• pp.43-48
• /
• 1972

Inertia friction welding, a relatively recent innovation in the art of joining materials, is a forge-welding process that releases kinetic energy stored in the flywheel as frictional heat when two parts are rubbed together under the right conditions. In a comparatively short time, the process has become a reliable method for joining ferrous, and dissimilar metals. The process is based on thrusting one part, attached to a flywheel and rotating at a relatively high speed, against a stationary part. The contacting surfaces, heated to plastic temperatures, are forged together to produce a reliable, high-strength weld. Welds are made with little or no workpiece preparation and without filler metal or fluxes. However, In order to obtain a good weld, the determination of the optimum weld parameters is an important problem. Especially, because the amount of the flywheel mass will be determined according to the initial rotating velocity values at the constant thrust load, the initial rotating velocity is an important factor to affect a weld character of the inertia-welded IN713C-SAE8630, which is used for the wheel-shafts of turbine rotors or turbochargers, exhausting valves, etc. In this paper, the effects of initial rotational velocity on a weld character of inertia-welded IN713C-SAE8630 was studied through considerations of weld parameters determination, micro-structural observations and tensile tests. The results are as the following: 1) As initial rotating velocity was reduced to 267 FPM, cracks and carbide stringers were completely eliminated in the micro-structure of welded zone. 2) As initial rotating velocity was reduced and flywheel mass was increased correspondingly, the maximum welding temperatures were decreased and the plastic working in the weld zone was increased. 3) As initial rotating velocity was progressively decreased and carbides were decreased, the tensile strengths were increased. 4) And also the fracture location moved out of the weld zone and the tensile tests produced, the failures only in the cast superalloy IN713C which do not extend into the weld area. 5) The proper initial rotating velocity could be determined as about 250 thru 350 FPM for the better weld character.

• 자동차안전학회지
• /
• 제5권1호
• /
• pp.16-24
• /
• 2013

Some GM (General Motors) vehicles are using a GMLAN (General Motors Local Area Network) communication protocol for control and diagnostics. The airbag control module uses vehicle speed information from the GMLAN to record the vehicle speed as pre-crash information. In order to use the vehicle speed information for crash reconstruction purposes, it helps to be able to understand the accuracy of the data. The actual vehicle speed is not expected to be the same as the GMLAN indicated speed in some situations like a spin or if there is hard braking. This paper compares the actual vehicle speed and vehicle speed information during specific vehicle maneuvers. Actual vehicle speed is calculated from a GPS sensor, while GMLAN vehicle speed is calculated from transmission output sensor by the Engine control module (ECM). Vehicle maneuvers defined as Mode #1, Mode #2, Mode #3. The Mode #1 maneuver simulates wheel lock-up and skidding f by hard-braking at a specific speed. The Mode #2 maneuver simulates a 90degree turn using a J-turn maneuver at a specific speed. The Mode#3 maneuver simulates a 180 degree turn using a spin type of maneuver at a specific speed. The study then compares the GMLAN speed and GPS speed to see what speed difference exists between them. The results of this paper are applicable to GM vehicles only. This paper catalogs the performance and limitations of two vehicles as useful reference for crash reconstructions where there is a need to understand the speed indicated in the pre-crash section of the SDM data.

• 한국정보통신학회논문지
• /
• 제9권8호
• /
• pp.1716-1721
• /
• 2005

본 논문에서는 ESP와 4WS 차량의 동적성능에 관한 연구와 차량이 불안정 영역으로의 주행 시 안정영역으로의 거동으로 할 수 있게 하는 차량의 주행안정성 향상에 관한 연구를 수행하였다. 고속으로 주행하는 차량이 조향과 동시에 가${\cdot}$감속을 하는 경우 관련된 변수로는 종방향 및 횡방향의 속도변화, 요우잉 등을 들 수 있으며, 이 변수들은 타이어 특성, 차량의 중량, 제동력, 조향각등에 따른 동역학적 관계식들로 표현 할 수 있다. 본 연구는 위와 같은 제동${\cdot}$조향장치들을 제어하여, 차량의 주행 중 위급상황 시 탁월한 성능을 발휘 할 수 있는 시스템에 관하여 고찰하고, 위급상황을 안전하게 회피하여 교통사고를 획기적으로 줄이기 위함이다.

• 한국한의학연구원논문집
• /
• 제12권1호
• /
• pp.39-48
• /
• 2006

The Following is a list of specific external and internal morphology of Rheum palmatum L. and R. undulatum L. in Rhei Rhizoma. 1. For the original plants of Rhei Rhizoma in the literatures. 18 plants are reported. 2. The external characteristics of original plant : R. palmatum has a large palmate leaf, its petiole of radical leaf has a simple bristle and its flower is purple and pink color. Whereas R. undulatum has a medium ovate leaf, its petiole of radical leaf is purphish, its stem leaf surrounds a half of stem and its flower is yellowish white color. 3. The character of herbal states : a. diameter and size-- R. palmaum is bigger and heavier than R. undulatum. b. in section--R. palmatum is dark brown color, R. undulatum is bright brown color Fibrovascular bundle is arranged in circle shape in R. patmatum. R. undulatum shows a distingushed wheel shape. 4. The internal characteristics : R. palmatum has a large intercellular space of cork layer, its cambium is clear and a xylem medullary ray is comparatively tight, Whereas R. undulatum has a tight intercettular space of cork layer., its cambium is a few clear and xylem medullary ray is verty tight. As these results, additional study is required to distinguish herbs and their effect among many kinds of same genus-degree of relatedness.