• Journal of Information Display
• /
• v.12 no.3
• /
• pp.159-165
• /
• 2011

This research entailed the production of stereoscopic 3D (S3D) contents using 2D-to-S3D conversion for exhibition at a museum and subjective evaluation. Hybrid production combining S3D images of existing live-action videos using the 2D-to-S3D conversion technology and computer graphic ones created via stereo rendering was conducted. Design and control of the chronological analysis of the parallactic angle was conducted on the produced contents, using binocular information as well as subjective evaluations, with the intent of conducting an investigation on the characteristics of such contents from the perspectives of the producers and viewers. An investigation was also conducted on the effects of the viewing position on the impressions of the S3D images.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.13 no.8
• /
• pp.764-768
• /
• 2002

In this paper, a double balanced gilbert cell MMIC mixer was realized in Tachyonics SiGe HBT technology. The fabricated mixer has 17 dB conversion gain, 9.8 dB noise figure, -4.2 dBm output 1 dB compression point, -27 dBc RF to IF isolation, and the good input, output matching characteristics. It draws 10 mA from a 3 V supply. The simulation and the measured results are closer to each other, which confirms accuracy of the model library and reliability of the process.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.35D no.8
• /
• pp.69-75
• /
• 1998

We demonstrate wavelength conversion of 2.5Gb/s optical signals by four-wave mixing (FWM) in a semiconductor optical amplifier (SOA). We investigate the effect of input pump and signal powers on the coversion efficiency, optical signal-to-noise ratio (OSNR) and extinction ratio to be a measure of performance in a wavelength converter. As a result, we show that the maximum bit error rate (BER) performance can be obtained by co promising among high-vonversion efficiency (minimum Pprobe), high-OSNR (maximum Pprobe) and low-cross-gain saturation effects (Pprobe kept at least 6dB weaker than Ppump). In our experiment, we obtain optimum performance at +3 dBm pump power and -6dBm signal power. The power penalty incurred in the wavelength conversion can be minimized by careful selection of the input pump and signal powers. We show that about 0.5dB power penalty for 3.2nm wavelength coversion at 10-10 BER is achievable.

• Explosives and Blasting
• /
• v.9 no.2
• /
• pp.3-7
• /
• 1991

The Problem of vibration Inflence to housing Construction fields has arised at the begining of 1970, at That time I used Lion(VM -l2B) which recorded only dB Demension. On the 1980's I have been used lnstantel made blastemate(DS-477), modern Instrument for measuring speed, Acc, frequency and placement. but The most of Jobsite used Lion I Carried out the empirical equation of conversion dB to cm /sec as follows. Single free face : dB = 140PPV + 30 double free face : dB = 143PPV + 20 Above equation Could apply on Rock type 3(soft rock)

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.10 no.3
• /
• pp.1159-1181
• /
• 2016

This study introduces an image-based 2D-to-3D conversion system that provides significant stereoscopic visual effects for humans. The linear and atmospheric perspective cues that compensate each other are employed to estimate depth information. Rather than retrieving a precise depth value for pixels from the depth cues, a direction angle of the image is estimated and then the depth gradient, in accordance with the direction angle, is integrated with superpixels to obtain the depth map. However, stereoscopic effects of synthesized views obtained from this depth map are limited and dissatisfy viewers. To obtain impressive visual effects, the viewer's main focus is considered, and thus salient object detection is performed to explore the significance region for visual attention. Then, the depth map is refined by locally modifying the depth values within the significance region. The refinement process not only maintains global depth consistency by correcting non-uniform depth values but also enhances the visual stereoscopic effect. Experimental results show that in subjective evaluation, the subjectively evaluated degree of satisfaction with the proposed method is approximately 7% greater than both existing commercial conversion software and state-of-the-art approach.

• Journal of Digital Convergence
• /
• v.10 no.9
• /
• pp.351-356
• /
• 2012

This paper presents the 2D/3D conversion technique using depth map which is generated based on the haze and relative height cue. In cases that only the conventional haze information is used, errors in image without haze could be generated. To reduce this kind of errors, a new approach is proposed combining the haze information with depth map which is constructed based on the relative height cue. Also the gray scale image from Mean Shift Segmentation is combined with depth map of haze information to sharpen the object's contour lines, upgrading the quality of 3D image. Left and right view images are generated by DIBR(Depth Image Based Rendering) using input image and final depth map. The left and right images are used to generate red-cyan 3D image and the result is verified by measuring PSNR between the depth maps.

• Journal of IKEEE
• /
• v.22 no.2
• /
• pp.408-412
• /
• 2018

In this paper, a 26GHz variable gain amplifier fabricated using a 40nm CMOS process is studied. In the case of an automobile radar using 79 GHz, it is advantageous in designing and driving to drive down to a low frequency band or to use a low frequency band before up conversion rather than designing and matching the entire circuit to 79 GHz in terms of frequency characteristics. In the case of a Phased Array System that uses time delay through TTD (True Time Delay) in practice, down conversion to a lower frequency is advantageous in realizing a real time delay and reducing errors. For a VGA (Variable Gain Amplifier) operating in the 26GHz frequency band that is 1/3 of the frequency of 79GHz, VDD : 1V, Bias 0.95V, S11 is designed to be <-9.8dB (Mea. High gain mode) and S22 < (Mea. high gain mode), Gain: 2.69dB (Mea. high gain mode), and P1dB: -15 dBm (Mea. high gain mode). In low gain mode, S11 is <-3.3dB (Mea. Low gain mode), S22 <-8.6dB (Mea. low gain mode), Gain: 0dB (Mea. low gain mode), P1dB: -21dBm (Mea. Low gain mode).

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.32 no.10C
• /
• pp.982-989
• /
• 2007

In this paper, we propose a 3DTV system that considers user's view point and display environment. The proposed system consists of 3 parts - multi-view encoder/decoder, face-tracker, and 2D/3D converter. The proposed system try to encode multi-view sequence and decode it in accordance with the user's view point and it also gives a stereopsis to the multi-view image by using of 2D/3D conversion which converts decoded two-dimensional(2D) image to three-dimensional(3D) image. Experimental results shows that we are able to correctly reconstruct a stereoscopic view that is exactly corresponding to user's view point.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.17 no.8 s.111
• /
• pp.719-724
• /
• 2006

In this paper, we designed the double conversion down mixer by using Half-LO frequency in 2.3 GHz band. The IF frequency is obtained by supplying two LO frequencies to HEMT in both gate type and resistive type. The proposed mixer uses Half-LO frequency the same way as conventional sub-harmonic mixers. However the proposed one uses fundamental component of Half-LO frequency in first stage instead of using second harmonic components of Half-LO frequency, and the IF frequency is obtained by resistive type mixer in second stage, thereby the proposed mixer can improve linearity in comparison with conventional active mixer. We can verify that the proposed mixer has an conversion loss of 5dBm and IIP3 of 16.25dBm by using 10 dBm Power.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.9 no.6
• /
• pp.1269-1276
• /
• 2005

In this paper, Mixer using the direct-conversion method intended to use in front-end of a RF receiver is designed. The direct conversion Mixer is an alternative wireless receiver architecture to the well-established superheterodyne, particularly for high integration, low power, and low cost. It operates at 2.4GHz band, and is designed and simulated with a 0.35um CMOS technology and HSPICE simulator. Layout is implemented with a Mentor IC Station. The 2.4GHz CMOS Mixer employs a modified single-balanced Gilbert Cell with additional MOSFET in the output stages to improve IIP2, which is a standard of linearity in direct conversion receiver. Additional coversion-stages's transconductances are controlled by each MOSFET's physical properties. The HSPICE simulation results show that the 2.4GHz CMOS Mixer has voltage gam of 29dB, IIP2 of 63dBm, respectively. The Mixer also draws 3.5mA from a 3.3V supply.