• Journal of the Korean Society of Clothing and Textiles
• /
• v.45 no.1
• /
• pp.106-122
• /
• 2021

This study confirmed the mechanical properties of an auxetic re-entrant pattern prepared using 3D printing technology and its composite fabric with neoprene for the production of functional auxetic patterns/textiles for safety shoes. Samples were prepared by the tilt angle of a re-entrant pattern of 0°, 30°, 45°, 60° and 90°, and then analyzed using Poisson's ratio, bending, compression, and tensile properties. A 3D printed auxetic re-entrant pattern (3DP-RE) and its composite fabric (3DP-RE/NP) showed a negative Poisson's ratio in all tilting angles that indicated auxetic properties. The results of the bending property shown that strength of 3DP-RE/NP was 1.5 times lower than NP, but the strain improved 2.0 times. It was confirmed that the deformation of 3DP-RE/NP is possible with a low load. Each sample type of compression behavior indicated similar regardless of the tilting angles; in addition, the compression toughness of 3DP-RE/NP increased 1.2 times compared with NP. In the case of tensile properties, 3DP-RE and 3DP-RE/NP were affected by the tilting angle, samples with 90° (the opposite of load direction) showed best tensile property and toughness. 3DP-RE/NP indicated improved bending, compression, and tensile properties.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2012.10a
• /
• pp.607-608
• /
• 2012

• Fashion & Textile Research Journal
• /
• v.13 no.1
• /
• pp.116-129
• /
• 2011

The purpose of this study is to research on changes of body surface according to golf movements in designs of golf slacks pattern and reflect it to designs of golf slacks pattern to enhance adaptability. For the first stage of this study, length of body surface was analyzed by using 3D body shape. In second stage, analysis of wearing test of golf slacks is performed to extract major pattern design factor of golf slacks and then research patterns were designed. In third stage, 4 differently designed 1st, 2nd slacks were used for analysis of 3D Clothing air volume. The results of this research is as follow. The variation rate of body surface length according to golf swing posture resulted the longest on back swing posture and follow through posture. Waist circumference-omphalion, thigh and ankle circumference increased more than 10% of body surface during golf swing. Front waist circumference-omphalion, right waist to hip length, left waist to hip length and right back center length were decreased more than 10%. As a result of analysis on measurements of 1st slacks pattern design, waist front center getting in values, waist front center going down value, front hip width, and front crotch extension had similar industrial pattern design. Back center line angle, back crotch extension, and knee center point~back waist center point had significant differences. The designs and ease proposed for golf slacks pattern in this study are waist circumference 75.5 cm(1.8 cm, 2.38%), hip circumference 95 cm(2 cm, 2.11%), crotch length(front: -0.8 cm, -1.25%; rear: -1.8 cm, -2.83%), slacks length 96c m, gradient of C.B.L $10^{\circ}$, crotch extension (back 9.2~10.4 cm, front 3.2 cm).

• The KIPS Transactions:PartD
• /
• v.11D no.1
• /
• pp.143-152
• /
• 2004

Recently, software programming method based on EJB for object oriented software design and implement has been used frequently. Usually, case that use permanent data that use Database in EJB base application is most. Part connected with Database-Access that take charge in Entity Bean class of server side creation program. In this paper using J2EE relationship DAO pattern class each separate. This is no much difference with existent pattern method, but in same pattern common classes are designed so that composition may be possible. And as well as use Entity Bean class that created each DBMS classes are different, is doing Rata Source so that connection work is available without alteration or creation of additional program in several DBMS environments.

• Journal of Sensor Science and Technology
• /
• v.25 no.6
• /
• pp.423-430
• /
• 2016

This study used a single metal oxide semiconductor (MOS) sensor to classify the major odorous gases hydrogen sulfide ($H_2S$), ammonia ($NH_3$) and toluene ($C_6H_5CH_3$). In order to classify these odorous substances, the voltage on the MOS sensor heater was gradually reduced in 0.5 V steps 5.0 V to examine the changes to the response by the cooling effect on the sensor as the voltage decreased. The hydrogen sulfide gas showed the highest sensitivity compared to odorless air under approximately 2.5 V and the ammonia and toluene gases showed the highest sensitivity under approximately 5.0 V. In other words, the hydrogen sulfide gas reacted better in the low temperature range of the MOS sensor, and the ammonia and toluene gases reacted better in the high-temperature range. In order to analyze the response characteristics of the MOS sensor by temperature in a pattern, a two-dimensional (2D) x-y pattern analysis was introduced to clearly classify the hydrogen sulfide, ammonia, and toluene gases. The hydrogen sulfide gas was identified by a straight line with a slope of 1.73, whereas the ammonia gas had a slope of 0.05 and the toluene gas had a slope of 0.52. Therefore, the 2D x-y pattern analysis is suggested as a new way to classify these odorous substances.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.10 no.5
• /
• pp.871-876
• /
• 2006

In this thesis, to accurately measure 3D face information using the spatial encoding patterns, the new algorithm to segment the pattern images from initial face pattern image is proposed. If the obtained images is non-homogeneous texture and ambiguous boundary pattern, the pattern segmentation is very difficult. Furthermore. the non-encoded areas by accumulated error are occurred. In this thesis, the FCM(fuzzy c-means) clustering method is proposed to enhance the robust encoding and segmentation rate under non-homogeneous texture and ambiguous boundary pattern. The initial parameters for experiment such as clustering class number, maximum repetition number, and error tolerance are set with 2, 100, 0.0001 respectively. The proposed pattern segmentation method increased 8-20% segmentation rate with conventional binary segmentation methods.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.17 no.7 s.110
• /
• pp.665-672
• /
• 2006

In this paper, we propose and fabricate the dual-band microstrip patch antenna with parasitic patch for S-DMB(Satellite-Digital Multimedia Broadcasting) and ITS (Intelligent Transport System) services. The measured - 10 dB bandwidth and the minimum return loss is 300 MHz and - 27 dB for S-DMB, 600 MHz and -17 dB for ITS, respectively. It is noticed that the measured and simulated results are agreed well. The S-DMB antenna has conical beam pattern in the vertical plane and has omni-directional beam pattern in the horizontal plane. The conical beam pattern has the maximum gain about 4.2 dBi when ${\theta}$ is $45^{\circ}$ at the center frequency of 2.6 GHz. The ITS antenna has directional beam pattern in the vertical plane that has maximum gain about 6.4 dBi when ${\theta}$ is $0^{\circ}$ at the center frequency of 5.8 GHz.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.22 no.4
• /
• pp.138-144
• /
• 2014

Now, Autonomous unmanned vehicle has become an issue in next generation technology. 2D Laser scanner as the distance measurement sensor is used. 2D Laser scanner detects the distance of 80m, measured angle is -5 to 185 degree. Laser scanner detects only the plane, but using motor swings. As a result, traffic signs detect and analyze patterns. Traffic signs when driving at low speed, shape of the detected pattern is very similar. By shaking the laser scanner, traffic signs and other obstacles became clear distinction.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.30 no.8
• /
• pp.1242-1252
• /
• 2006

Many applications in computer graphics require complex, highly detailed models. However, to control processing time, it is often desirable to use approximations in place of excessively detailed models. Therefore, we have developed the notion of an optimal matrix to simplify the model surface which can then rapidly obtain high quality 2D patterns by flattening the 3D surface. Firstly, the woman's 3D body was modeled based on Size Korea data. Secondly, the 3D model was divided by shell and block for the pattern draft. Thirdly, each block was flattened by the grid and bridge method. Finally, we select the optimal matrix and demonstrate it's efficiency and quality. The proposed approach accommodates surfaces with darts, which are commonly utilized in the clothing industry to reduce the deformation of surface forming and flattening. The resulting optimal matrix could be an initiation of standardization for pattern flattening. This can facilitate much better approximations, in both efficiency and exactness.

• Transactions of Materials Processing
• /
• v.33 no.2
• /
• pp.123-131
• /
• 2024

Plastic, the main material of FFF-type 3D printing, exhibits lower strength compared to metal. research aimed at increasing strength is needed for use in various industrial fields. This study analyzed three X-shape infill patterns(grid, lines, zigzag) with similar internal lattice structure. Moreover, tensile test considering weight and printing time was conducted based on the infill line multiplier and infill overlap percentage. The three X-shape infill patterns(grid, lines, zigzag) showed differences in nozzle paths, material usage and printing time. When infill line multiplier increased, there was a proportional increase in tensile strength/weight and tensile strength/printing time. In terms of infill overlap percentage, the grid pattern at 50% and the zigzag and lines patterns at 75% demonstrated the most efficient performance.