• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.47 no.3
• /
• pp.18-27
• /
• 2010

In this paper, a 1.2V 7-bit 1GSPS A/D converter with offset self-calibration is proposed. The proposed A/D converter structure is based on the folding-interpolation whose folding rate is 2, interpolation rate is 8. Further, for the purpose of improving the chip performance, an offset self-calibration circuit is used. The offset self-calibration circuit reduce the variation of the offset-voltage，due to process mismatch, parasitic resistor, and parasitic capacitance. The chip has been fabricated with a 1.2V 65nm 1-poly 6-metal CMOS technology. The effective chip area is $0.87mm^2$ and the power dissipates about 110mW at 1.2V power supply. The measured SNDR is about 39.1dB when the input frequency is 250MHz at 800MHz sampling frequency. The measured SNDR is 3dB higher than the same circuit without any calibration.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.30 no.2 s.245
• /
• pp.141-148
• /
• 2006

In this paper, a new offset algorithm for closed 2D lines with islands is introduced and the result is illustrated. The main point of the proposed algorithm is that every point is set to be an offset by using bisectors, and then invalid offset lines, which are not to be participated in offsets, are detected in advance and handled with an invalid offset edge handling algorithm. As a result, raw offset lines without local invalid loops are generated. The proposed offset method is proved to be robust and simple, moreover, has a near O(n) time complexity, where n denotes the number of input lines. In addition, the proposed algorithm has been implemented and tested with 2D lines of various shapes.

• Proceedings of the KIEE Conference
• /
• 2003.11c
• /
• pp.1022-1030
• /
• 2003

In this paper we propose a efficient offset curve construction algorithm for $C^0$-continuous Open and Closed 2D sequence curve with line segment in the plane. One of the most difficult problems of offset construction is the loop problem caused by the interference of offset curve segments. Prior work[1-10] eliminates the formation of local self-intersection loop before constructing a intermediate(or raw) offset curve, whereas the global self-intersection loop are detected and removed explicitly(such as a sweep algorithm[13]) after constructing a intermediate offset curve. we propose an algorithm which removes global as well as local intersection loop without making a intermediate offset curve by forward tracing of tangential circle. Offset of both open and closed poly-line segment sequence curve in the plane constructs using the proposed approach.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.43 no.10 s.352
• /
• pp.97-103
• /
• 2006

This paper presents the method of improving second order intermodulation distortion(IMD2) and dc-offset problems in down-conversion mixer. A simple analysis reveals the IMD2 and dc-offset can be eliminated by controlling the duty cycles of local oscillator(LO) inputs. A mixer with the proposed method has been simulated with a $0.13{\mu}m$ RF CMOS technology with 5% mismatch in the load resistance, the mixer shows 2.04dBm IIP2 and 22mnV input referred DC-offset. By controlling two duty cycles of LO inputs, IIP2 and DC-offset can be improved to 38.8dBm and $777{\mu}V$, respectively.

• Journal of Satellite, Information and Communications
• /
• v.12 no.1
• /
• pp.125-131
• /
• 2017

In this paper, an efficient structure of device-to-device (D2D) synchronization preamble is proposed to meet the enhanced time and frequency synchronization requirements for D2D communication. D2D communication can be applied not only for the cellular communications, but also unmaned aerial vehicle communications and vehicle-to vehicle communication. The proposed preamble structure is transmitting signals at every odd subcarriers, and empty the other subcarriers to minimize the effect of inter-carrier interference. According to the simulation results, the proposed preamble structure provides improved time offset estimation performance, without degrading frequency offset estimation performance compared to the current LTE D2D preamble.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.16 no.3
• /
• pp.1-8
• /
• 2017

Tool path generation is a part of process planning in 3D printing. This is done before actual printing by a computer rather than an AM machine. The mesh geometry of the 3D model is sliced layer-by-layer along the Z-axis and tool paths are generated from the sliced layers. Each 2-dimensional layer can have two types of printing paths: (i) shell and (ii) infill. Shell paths are made of offset loops. During shell generation, twists can be produced in offset loops which will cause twisted tool paths. As a twisted tool path cannot be printed, it is necessary to remove these twists during process planning. In this research, An algorithm is presented to remove twists from the offset loops. To do so the path segments are traversed to identify twisted points. Outer offset loops are represented in the counter-clockwise segment order and clockwise rotation for the inner offset loop to decide which twisted loop should be removed. After testing practical 3D models, the proposed algorithm is verified to use in tool path generation for 3D printing.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2008.06a
• /
• pp.333-334
• /
• 2008

• Korean Journal of Computational Design and Engineering
• /
• v.3 no.2
• /
• pp.127-134
• /
• 1998

This paper presents d new algorithm to compute the offlet curve of a given planar parametric curve. We reduce the problem of computing an offset curve to that of intersecting a surface to a paraboloid. Given an input curve C(t)=(x(t), y(t))∈R², the corresponding surface D/sub c(t)/ is constructed symbolically as the envelope surface of a one-parameter family of tangent planes of the paraboloid Q:z=x²+y²along a lifted curve C(t)=(x(t), y(t), x(t)²+y(t)²∈Q. Given an offset distance d∈R, the offset curve C/sub d/(t) is obtained by the projection of the intersection curve of D/sub c(t)/ and a paraboloid Q:z=x²+y²-d² into the xy-plane.

• Journal of electromagnetic engineering and science
• /
• v.8 no.3
• /
• pp.134-137
• /
• 2008

This paper proposes a novel quadrature VCO(QVCO) based on direct back-gate second harmonic coupling. The QVCO directly couples the current sources of the conventional LC VCOs through the back-gate instead of front-gate to generate quadrature signals. By the second harmonic injection locking, the two LC VCOs can generate quadrature signals without using on-chip transformer, or stability problem that is inherent in the direct front-gate second harmonic coupling. The proposed QVCO is implemented in $0.18{\mu}m$ CMOS technology operating at 2 GHz with 5.0 mA core current consumption from 1.8 V power supply. The measured phase noise of the proposed QVCO is - 63 dBc/Hz at 10 kHz offset, -95 dBc/Hz at 100 kHz offset, and -116 dBc/Hz at 1 MHz offset from the 2 GHz output frequency, respectively. The calculated figure of merit(FOM) is about -174 dBc/Hz at 1 MHz offset. The measured image band rejection is 46 dB which corresponds to the phase error of $0.6^{\circ}$.

• Journal of Fashion Business
• /
• v.20 no.4
• /
• pp.153-171
• /
• 2016

With the advent of smart clothing for health care and sports, the sophisticated designs with curved seams are drawing attention. One of the problems in those clothing is to determine the design curves in 2D pattern, such that it corresponds to the lines on the intended 3D body. Moreover, the difficulty increases when the original pattern needs to be changed for various sizes and body types. We compare two methods of pattern enlargement in this paper: one is the offset/projection type, and the other is the split grading type. For the enlarged pattern with offset/projection type, the 3D surface offset was first adopted to transform the standard lower body to the target larger size; next, the design lines were projected to the new 3D surface, following which the 3D pattern was developed from the newly transformed 3D surface. In the second method, the enlarged pant patterns were developed by the split grading method. Here, a 3D pattern was developed from the initial body, and then enlarged to the target size by the conventional split grading method. Two feminine pants patterns were examined by 3D virtual fitting. We observed that the 3D offset/projection pants pattern was well fitted, having an evenly distributed surplus, as compared with the sample developed using the split grading method. The difference between the two patterns were apparent at the location where several curved lines merged.