• Journal of the Korean Magnetics Society
• /
• v.18 no.3
• /
• pp.120-125
• /
• 2008

In this study, NiCoZn ferrites with the variation of sintering temperature and chemical composition were prepared by the coprecipitation. Microstructures Crystal structure of NiCoZn ferrites were analyzed by XRD and their electric magnetic characteristics were analyzed by LCR meter and their morphology observed by SEM. We identified that these powders have a typical NiCoZn spinel structure and nanoparticles average size of 40 nm. The impurity, the initial permeability and the Q factor value are the lowest of sintered NiCoZn ferrite at $1250^{\circ}C$. Also, we measured S-parameter for $(Ni_{0.4}Co_{0.1}Zn_{0.5})Fe_2O_4$ which showed a maximum reflection loss of -3.1 dB at 6 GHz for the 2 mm thick sample. From this result, we found that the NiCoZn ferrite can be used in ferrite microwave-absorbing application at a higher frequency region (> 6 GHz).

• Journal of KIISE:Information Networking
• /
• v.36 no.2
• /
• pp.118-129
• /
• 2009

The ISO 18000-7 Active RFID standard, a single channel system operating in the 433Mhz, faces technical difficulties in supporting some recently introduced application demands because of its low transmission rates and radio interference between readers. We propose a new multi-channel active RFID system operating in the 2.4Ghz. The special feature of the proposed system is that a reader makes use of multiple interfaces to improve its performance like a multi-core processor. However if only a small part of interfaces are actually used, the performance improvement would not meet the expectation. To overcome this problem, a new multi-channel multi-interface active RFID protocol, which balances communication loads among all available interfaces, is necessary. 3 protocols, named as "Aggregated", "LP-Combined", "AP-Balanced", are proposed. Through simulation, we compare them for various conditions by changing number of tags, number of interfaces, tag data size. AP-Balanced shows the best performance and its performance increases almost linearly as the number of interface increases, which meets our expectation.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.42 no.7 s.337
• /
• pp.41-48
• /
• 2005

We design and fabricate 3-dB tandem directional coupler using the coplanar waveguide structure which is applicable to balanced amplifiers and mixers for 60 GHz wireless local area network system. The coupler comprises the multiple-sectional parallel-coupled lines to facilitate the fabrication process, and enable smaller device size and higher directivity than those of the conventional 3-dB coupler employing the edge-coupled line. In this study, we adopt the structure of two-sectional parallel-coupled lines of which each single-coupled line has a coupling coefficient of -8.34 dB and airbridge structure to monolithically materialize the uniplanar coupler structure instead of using the conventional multilayer or bonded structure. The airbridge structure also supports to minimize the parasitic components and maintain desirable device performance in V-band (50$\~$75 GHz). The measured results from the fabricated couplers show couplings of 3.S$\~$4 dB and phase differences of 87.5$^{\circ}{\pm}1^{\circ}$ in V-band range and show directivities higher than 30 dB at a frequency of 60 GHz.

• Journal of Advanced Navigation Technology
• /
• v.11 no.3
• /
• pp.281-287
• /
• 2007

The Bluetooth technology represents an attractive approach to enable short distance wireless connectivity. The Bluetooth standard operates at the 2.4 GHz ISM band and offers the advantage of establishing ad hoc networks, called piconet and scatternet. The spread of Bluetooth implementation in consumer products opens up a new short range wireless networking applications. Bluetooth MAC avoids packet collision within a piconet by simple time multiplexing. But lack of synchronization among independent neighboring piconets introduces packet overlapping within a time slot. In this paper, the wireless network throughput of Bluetooth packet transmission system applying the pure-ALOHA and slotted-ALOHA MAC is investigated according to the impact of channel environment. From the obtained results, the throughput of the Bluetooth MAC protocol shown to offer good performance in wireless channel, and the results are useful for the implementation of Bluetooth networks.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.44 no.2 s.314
• /
• pp.32-38
• /
• 2007

This paper represents a Doherty amplifier (DPA) with analog predistorter (PD) to improve the linearity of the DPA while preserving the high efficiency. A third-order PD cancels fifth-order intermodulation (IM5) as well as third-order intermodulation (IM3) components by their same phase difference in the PD and DPA. This is accomplished by independently controlling their phase by using the phase-controlled error generator in the PD. Also, we confirm the phase-control ability of the error generator experimentally with a simple and accurate phase measurement setup. For experimental verification, a third-order PD has been implemented and tested in a 180-W DPA at the wide-band code division multiple access (WCDMA) band of 2.11-2.17 GHz. Two-tone test results show that significant cancellation of IM3 and IM5 components can be obtained. For four-carrier WCDMA applications, significant adjacent channel leakage ratio (ACLR) improvement is achieved over a wide range of output power levels. This technique is cost-effective and convenient due to its simple structure, compact size, and three control parameters.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.13 no.7
• /
• pp.667-678
• /
• 2002

In this paper, a new radiating structure with a multi-layered two-dimensional metallic disk array was proposed for shaping the flat-topped element pattern. It is an infinite periodic planar array structure with metallic disks finitely stacked above the radiating circular waveguide apertures. The theoretical analysis was in detail performed using rigid full-wave analysis, and was based on modal representations for the fields in the partial regions of the array structure and for the currents on the metallic disks. The final system of linear algebraic equations was derived using the orthogonal property of vector wave functions, mode-matching method, boundary conditions and Galerkin's method, and also their unknown modal coefficients needed for calculation of the array characteristics were determined by Gauss elimination method. The application of the algorithm was demonstrated in an array design for shaping the flat-topped element patterns of $\pm$20$^{\circ}$ beam width in Ka-band. The optimal design parameters normalized by a wavelength for general applications are presented, which are obtained through optimization process on the basis of simulation and design experience. A Ka-band experimental breadboard with symmetric nineteen elements was fabricated to compare simulation results with experimental results. The metallic disks array structure stacked above the radiating circular waveguide apertures was realized using ion-beam deposition method on thin polymer films. It was shown that the calculated and measured element patterns of the breadboard were in very close agreement within the beam scanning range. The result analysis for side lobe and grating lobe was done, and also a blindness phenomenon was discussed, which may cause by multi-layered metallic disk structure at the broadside. Input VSWR of the breadboard was less than 1.14, and its gains measured at 29.0 GHz. 29.5 GHz and 30 GHz were 10.2 dB, 10.0 dB and 10.7 dB, respectively. The experimental and simulation results showed that the proposed multi-layered metallic disk array structure could shape the efficient flat-topped element pattern.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.2 s.117
• /
• pp.126-135
• /
• 2007

This paper proposes a new miniaturization method for a parallel coupled line filter with enhanced bandwidth characteristics. A previous method incorporated several advantages, such as size reduction through the use of only a small number of capacitors, in addition to grounding, suppression of harmonic characteristics, and improved skirt characteristics for the parallel coupled line filter, which is conventional in the field of RE filters due to its design and fabrication simplicity. However, the previous method also has disadvantages related to the bandwidth shrinkage of the miniaturized filters. In this paper, the amount of bandwidth shrinkage is analyzed in terms of the relationship between the loaded Q(quality factor) and the group delay of a resonator. Moreover, the reduction in the bandwidth is solved by a design with new design equations. To show the validity of the proposed method, a hairpin filter with a center frequency of 5.2 GHz and an fractional bandwidth(FBW) of 10% was scaled down to half its original dimension by the proposed method with the enhanced bandwidth characteristics. The measured result shows a high level of agreement with theoretical results.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• v.9 no.1
• /
• pp.757-759
• /
• 2005

최근에 낮은 가격과 전력을 내세워 응용서비스를 제공할 수 있는 Bluetooth를 탑재한 많은 무선 제품들이 출시되고 있다. 그러나 1Mbps의 저속, 다른 무선 기기들과의 상호 간섭과 호환성 문제 그리고 보안 문제 등 많은 제약 조건이 따름에도 불구하고 이동전화, 컴퓨터, PDA 등 근거리 무선접속을 사용하고 있는 가정이나 회사의 전화나 컴퓨터들과 어떻게 서로 쉽게 연결될 수 있을까에 대한 꾸준한 연구가 활발히 진행되고 있다. Bluetooth 무선 기술은 음성 및 데이터 전송을 위한 단거리 일대다중 무선 주파수 통신을 위해 제안된 무선통신 기술이다. Bluetooth는 2.4GHz ISM Band에서 동작하며 약 10m 범위의 다양한 이동 장치와 휴대용 장치를 위한 저가격의 기저대역 무선 접속을 제공한다. 본 논문에서 Bluetooth의 기술적 측면을 알아보고 이를 이용해 현재 시장에 출시된 Bluetooth 기기중 하나인 One Phone을 소개하려 한다. 또한 Bluetooth의 발전 가능성에 대하여 알아본다.

• The KIPS Transactions:PartC
• /
• v.19C no.4
• /
• pp.239-246
• /
• 2012

The function of location estimation in WPAN has been studied and specified on the ultra wide band optionally. But the devices based on CSS(Chirp Spread Spectrum) specification has been used widely in the market because of its functionality, cheapness and support of development. As the CSS device uses 2.4GHz for a carrier frequency and the sampling frequency is lower than that of the UWB, the resolution of a timestamp is very coarse. Then actually the error of a measured distance is very large about 30cm~1m at 10 m depart. And the location error in ($10m{\times}10m$) environment is known as about 1m~2m. So for some applications which require more accurate location information, it is very natural and important to develop a sophisticated post processing algorithm after distance measurements. In this paper, we have studied extended Kalman filter with the frequency offsets of anchor nodes, and proposed a novel algorithm frequency offset compensated extended Kalman filter. The frequency offsets are composed with a variable as a common frequency offset and constants as individual frequency offsets. The proposed algorithm shows that the accurate location estimation, less than 10cm distance error, with CSS WPAN nodes is possible practically.

• Journal of Advanced Navigation Technology
• /
• v.4 no.2
• /
• pp.171-181
• /
• 2000

In this paper, we propose an AVLS(Automatic Vehicle Location System) using the DSRC(Dedicated Short Range Communication) which adopts a radio communication tool between RSE(Road-Side Equipment) and OBE(On-Board Equipment) on a vehicle and uses the ISM bandwidth of 5.8GHz radio frequency. Typical AVLS uses the sensors for detecting the vehicle, but the DSRC system is developed for supporting various services such as the position of vehicle, clearance, vehicle to vehicle communication, collection and distributions of traffic and road information. Also, for fast processing, we design three-layer configuration of physical(L1), data link(L2), and application layer(L7), which simplifies the seven-layer configuration. We suggest the proposed system as a new technology for replacement of typical wireless communication system and sensors for AVLS.