• Journal of Electrical Engineering and Technology
• /
• v.11 no.3
• /
• pp.707-714
• /
• 2016

We present a piezoelectric energy harvester with stopper-engaged dynamic magnifier which is capable of significantly increasing the operating bandwidth and the energy (power) harvested from a broad range of low frequency vibrations (<30 Hz). It uses a mass-loaded polymer beam (primary spring-mass system) that works as a dynamic magnifier for another mass-loaded piezoelectric beam (secondary spring-mass system) clamped on primary mass, constituting a two-degree-of-freedom (2-DOF) system. Use of polymer (polycarbonate) as the primary beam allows the harvester not only to respond to low frequency vibrations but also generates high impulsive force while the primary mass engages the base stopper. Upon excitation, the dynamic magnifier causes mechanical impact on the base stopper and transfers a secondary shock (in the form of impulsive force) to the energy harvesting element resulting in an increased strain in it and triggers nonlinear frequency up-conversion mechanism. Therefore, it generates almost four times larger average power and exhibits over 250% wider half-power bandwidth than those of its conventional 2-DOF counterpart (without stopper). Experimental results indicate that the proposed device is highly applicable to vibration energy harvesting in automobiles.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.15 no.2 s.95
• /
• pp.135-147
• /
• 2005

As automobile technology advances, a smoother ride with less noise is desired. In order to achieve these purposes, a study on the vibration and noise produced by a moving automobile was carried out and a model for tire vibration characteristics which influence the ride performance was developed. The model was verified through simulations and experiments. The developed model was then applied to a half car model and automobile vibrations were analyzed. The effects of tire design parameters on the automobile vibration energy were investigated. The results from laboratory and field tests confirm the validity of the analytical model. The 17-DOF half-car model was built to analyze automobile vibration. The characteristics of the nonlinear model for a shock absorber were applied to this model. The results from the present 17-DOF half car model incorporating the analytical tire model with tire design parameters, were compared with the 5-DOF half car model where the tire was modeled with linear springs. The results of the 17-DOF model are close to the experimental results. Using the 17-DOF model, the influence of tire design parameter were considered. According to the analysis results, the vibrations at seat/body/wheel were predicted by simulation and experiment.

• Journal of Institute of Control, Robotics and Systems
• /
• v.4 no.3
• /
• pp.321-328
• /
• 1998

When we control the level of the steam generator in the nuclear power plants, a swell and shrink arises from many disturbances such as feed water rate, feed water temperature, main steam flow rate, and coolant temperature. If we use the conventional type of PI controller in this system, we will not have stability during controlling at lower power, the removal function of disturbances, and a load follow-up control effectively. In this paper, we study the application of a 2-Degree of Freedom(2-DOF) PID controller to the level control of the steam. generator of nuclear power plants through the simulation and the experimental steam generator. We use the parameters $\alpha$, $\beta$, $\gamma$ of the 2-DOF PID controller for the removal of disturbances and the parameters Kp,Ti,Td of the conventional type of PID controller for controlling setpoint. The back-propagation learning algorithm of neural network is used for tuning the 2-DOF PID controller. We can find satisfactory results of the removal of the disturbances and the tracking function in the change of setpoint through the simulation and experimental steam generator.

• 제어로봇시스템학회:학술대회논문집
• /
• 2002.10a
• /
• pp.51.4-51
• /
• 2002

$\textbullet$ A noval haptic mouse system is developed for human computer interface. $\textbullet$ Five bar mechanism is adapted for 2 dof force feedback with virtual environment. $\textbullet$ Double prismatic joint type mechanism is adapted to reflect 1 dof grabbing force feedback. $\textbullet$ Cable driven mechansim is used for actuation to reduce backlash and endow backdrivability. $\textbullet$ Virtual wall perception experiment is conducted to obtain force specification for haptic mouse. $\textbullet$ Average mouse workspace is measured using magnetic position tracker.

• Smart Structures and Systems
• /
• v.20 no.2
• /
• pp.181-195
• /
• 2017

In this study, the severity of damage in tendon anchorage caused by the loss of tendon forces is quantitatively identified by using the PZT interface-based impedance monitoring technique. Firstly, a 2-DOF impedance model is newly designed to represent coupled dynamic responses of PZT interface-host structure. Secondly, the 2-DOF impedance model is adopted for the tendon anchorage system. A prototype of PZT interface is designed for the impedance monitoring. Then impedance signatures are experimentally measured from a laboratory-scale tendon anchorage structure with various tendon forces. Finally, damage severities of the tendon anchorage induced by the variation of tendon forces are quantitatively identified from the phase-by-phase model updating process, from which the change in impedance signatures is correlated to the change in structural properties.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1995.10a
• /
• pp.555-558
• /
• 1995

In designing the anti-sway controller for crane system in the industrial field, one of the basic problem is to keep the stability of system, even if the mathematical model of the plant is not exact and disturbance exists. Form this point of view, a two-degree-of-freedom(2DOF) servo controller effact to the system in which the integral compensation is effctive only when a modeling error and/or a disturbance input exist. In this paper, the change of load weight and variation of wire rope length considered as the structured uncertainty, and design the 2DOF servo contorller using independently the informations of reference signal and control output with both feedforward and feedback. The effectivenss is proved through the results for the anti-sway system in the system with the position control of trolley.

• Journal of Biosystems Engineering
• /
• v.25 no.1
• /
• pp.63-70
• /
• 2000

In Korea, researches for year-round leaf vegetables production system are in progress and the most of them are focused on environment control. Automation technologies for harvesting , transporting and grading need to be developed. This study was conducted to develop harvesting process automation system profitable to a competitive price. 1. Manipulator and end-effector are to be designed and fabricated , and fuzzy logic controller for controlling these are to be composed. 2. The entire system constructed is to be evaluated through a performance test. A robot system for harvesting a lettuce was developed. It was composed of a manipulator with 20DOF (degrees of freedom) an end-effector, a lettuce feeding conveyor , an air blower , a machine vision device, 6 photoelectric sensors and a fuzzy logic controller. A fuzzy logic control was applied to determined appropriate grip force on lettuce. Leaf area index and height index were used as input parameters, and voltage was used as output parameter for the fuzzy logic controller . Success rate of the lettuce harvesting system was 93.06% , and average harvesting time was about 5 seconds per lettuce.

• Journal of Institute of Control, Robotics and Systems
• /
• v.22 no.7
• /
• pp.502-507
• /
• 2016

In this paper, we propose a tracking control method for a quadrotor equipped with a 2-DOF manipulator, which is based on the multiple sliding surface control (MSSC) method. To derive the model of a quadrotor equipped with a 2-DOF manipulator, we obtain the models of a quadrotor and a 2-DOF manipulator based on the Lagrange-Euler formulation separately - and include the inertia and the reactive torque generated by a manipulator when these obtained models are combined. To make a quadrotor equipped with a manipulator track the desired path, we design a double-loop controller. The desired position is converted into the desired angular position in the outer controller and the system's angle tracks the desired angular position through the inner controller based on the MSSC method. We prove that the position-tracking error asymptotically converges to zero based on the Lyapunov stability theory. Finally, we demonstrate the effectiveness of the proposed control system through a computer simulation.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.25 no.2
• /
• pp.105-110
• /
• 2015

This study proposes the more improved mathematical model than conventional that for the 3-DOF Helicopter System in Quanser Inc., and checks the validity about the proposed model by performance comparison between the controller based on the conventional model and that based on the proposed model. Research process is next : First, analyze the dynamics for the 3-DOF helicopter system and establish the linear mathematical model. Second, check the eliminated nonlinear-elements in linearization process for establishing the linear mathematical model. And establish the improved mathematical model including the parameters corresponding to the eliminated nonlinear-elements. At that time, it is used for modeling that Particle Swarm Optimization algorithm the meta-heuristic global optimization method. Finally, design the controller based on the proposed model, and verify the validity of the proposed model by comparison about the experimental results between the designed controller and the controller based on the conventional model.

• Journal of Institute of Control, Robotics and Systems
• /
• v.6 no.6
• /
• pp.471-477
• /
• 2000

The position control accuracy of a robot arm is significantly deteriorated when a long arm robot is operated at a high speed. In this case, the robot arm must be modeled as a flexible structure, not a rigid one, and its control system should be designed with its elastic modes taken into account. In this paper, the tip position control scheme of a one-link flexible manipulator using 2-DOF controller with sliding mode is presented. The robot consists of a flexible arm manufactured with a thin aluminium plate, an AC servo motor with a harmonic drive for speed reduction, an optical encoder and a CCD camera as a vision sensor for on-line measuring the tip deflection of the flexible m. Simulation and experimental results of the flexible manipulator with a proposed controller are provided to show the effectiveness of the controller.