• 설비공학논문집
• /
• 제16권5호
• /
• pp.490-498
• /
• 2004

This paper measures the forced convective heat transfer from heated cylinder to air flow in a rectangular duct at Re$_{D}$ =2,337, 4,589, 6,621 and 7,944 through experiments. And the heat transfer is computed by 3-D numerical computation in which various turbulent models are applied. It is shown through the comparison of experimental and computed data that numerical computation with standard k-$\varepsilon$ model predicts the experimental data most accurately. Furthermore, the correlation from the computed heat transfer is almost similar to that from the experiment when Re$_{D}$ is greater than 4,589. In addition, the correlation of McAdams is the closest to that from experimental data among various correlations from literature in the range of Reynolds number.ber.

• 대한기계학회논문집B
• /
• 제28권8호
• /
• pp.910-920
• /
• 2004

The heat/mass transfer characteristics in a rotating two-pass duct with and without rib turbulators are investigated in the present study. The square duct has a hydraulic diameter ($D_h$) of 26.7 mm, and $1.5\;mm{\times}1.5\;mm$ square $90^{\circ}$-rib turbulators are attached on the leading and trailing walls. The pitch-to-rib height ratio (p/e) is 10. The Reynolds number based on the hydraulic diameter is kept constant at 10,000 to exclude the Reynolds effect, and the rotation number is varied from 0.0 to 0.20. In the smooth duct, the curvature of the $180^{\circ}$-turn produces Dean vortices that enhance heat/mass transfer in the post-turn region. When rib turbulators are installed, heat/mass transfer is augmented 2.5 times higher than that of the smooth duct since the main flow is turbulated by reattaching and separating in the vicinity of the duct surfaces. The duct rotation results in heat/mass transfer discrepancy so that Sherwood number ratios are higher on the trailing surface in the first-pass and on the leading surface in the second-pass. In the turning region, Dean vortices shown in the stationary case transform into one large asymmetric vortex cell, and subsequent heat/mass transfer characteristics also change. As the rotation number increases, the heat/mass transfer discrepancy enlarges.

• 한국소음진동공학회논문집
• /
• 제13권5호
• /
• pp.357-363
• /
• 2003

There have been lots of studies on noise transmission analysis and noise reduction In ducts. In order to reduce the noise transmission in ducts. active noise cancellation techniques have often been employed and a rotation shaft with blades has sometimes been suggested. These Ideas were not successfully commercialized because of the limitation of real life such as size or application difficulties. This study investigated how a rotational shaft with blades could reduce the noise transmission in a duct. To do so, an assembly of the shaft and the $haft housing was built In the middle of a duct. and the clearance between the blades and the housing was 0.2 mm. The noise reduction was experimentally evaluated with respect to the number of blades. the rotation speed, and the rotation or stop. This paper showed that the noise reduction resulted in about 14∼19 dBA regardless of the three test conditions only If the blades always blocked the duct. And. the noise reduction increased due to the higher number of blades and the lower speed of the shaft.

• 설비공학논문집
• /
• 제2권1호
• /
• pp.1-10
• /
• 1990

In the present study, the entrance length, velocity profiles and waveforms of developing transitional steady flows in a square duct are investigated analytically and experimentally. The systems of conservation equations for transitional steady duct flows are solved analytically by linearizing non-linear convective terms and adoption of modified eddy viscosity from empirical correlations. Analytical solutions of velocity profiles for developing transitional steady flow were obtained in the form of infinite series. The experimental study for transitional steady flow in a square duct with $40mm{\times}40mm{\times}4000mm$($width{\times}height{\times}length$) was carried out to measure velocity profiles and other parameters by using a hot-wire anemometer with data acquisition and processing system. The entrance length of developing transitional steady flows in a square duct was $L_e{\fallingdotseq}0.02{\cdot}Re,st{\cdot}D_h$, and the overshoot was occured at about 30 times of hydraulic diameter because of the effect of external velocity of boundary layer and instantaneous acceleration.

• 한국전산유체공학회지
• /
• 제12권2호
• /
• pp.46-52
• /
• 2007

An experimental and numerical investigation of the ejector-jets focusing on its geometric parameters that effect on thrust performance was carried out. The area ratio of the primary nozzle that was tested in the present study was 2.17 and 3.18, while the ratio of the length to the diameter of the duct downstream the primary nozzle inlet had values of 3.41, 6.82, and 10.23. Internal flow properties of ejector-jet were estimated by comparison experiment data and CFD analysis for basic study of ejector-jet thrust performance. For examination of thrust performance, the thrust ratios increased with increase in L/D. Especially at AR=2.17, the maximum thrust augmentation was 33 percent for the shortest L/D. It is expected that the increase of mixing duct length of ejector-jet will be helpful in a thrust performance by improving mixing efficiency.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2007년도 춘계 학술대회논문집
• /
• pp.166-170
• /
• 2007

An experimental and numerical investigation of the ejector-jets focusing on its geometric parameters that effect on thrust performance was carried out. The area ratio of the primary nozzle that was tested in the present studywas 2.17 and 3.18, while the ratio of the length to the diameter of the duct downstream the primary nozzle inlet had values of 3.41, 6.82, and 10.23. Internal flow properties of ejector-jet were estimated by comparison experiment data and CFD analysis for basic study of ejector-jet thrust performance. For examination of thrust performance, the thrust ratios increased with increase in L/D. Especially at AR=2.17, the maximum thrust augmentation was 34 percent for the shortest L/D. It is expected that the increase of mixing duct length of ejector-jet will be helpful in a thrust performance by improving mixing efficiency.

• 소음진동
• /
• 제2권2호
• /
• pp.107-116
• /
• 1992

An adaptive signal processing technique is implemented for the active noise cancellation of the plane acoustic wave propagating in a duct. To avoid the instability caused by the acoustic feedback from the control speaker to the detect microphone, an off-line modeling of the acoustic feedback plant is done using the FIR filter. Auxiliary path required for the filtered-x LMS algorithm is modeled as well. Before going into the experiments, a simulation is carried out under the same conditions with experiments. The simulation shows that the longer the length of the adaptive filter is, the better the results are achieved. Experiments have been carried out at lower audio frequency range (50 - 400Hz), and the results are in good agreements with those of simulation study. As a results of this adaptive noise control, around 50dB is reduced for a pure tone noise, and for a bandlimited noise with the bandwidth of 316Hz, a maximum of 30dB noise reduction is attained.

• 대한기계학회논문집 C: 기술과 교육
• /
• 제5권2호
• /
• pp.97-104
• /
• 2017

본 논문에서는 휠로더 냉각성능 평가를 위한 열유동해석의 효율성 향상과 비용 저감을 위해서 흡배기구 다공판형상을 Porous media 기법을 이용하여 단순화하고 해석 정도를 확인하였다. 여기서 Porous media에 적용된 다공판형상의 유동손실계수는 시험데이터를 바탕으로 정의하였다. 또한 다공판형상의 유동손실계수를 해석적으로 정의하기 위해 단위형상에 대한 압력손실을 계산하고 시험결과와 비교하였다. 마지막으로 휠로더 흡배기구를 단순화한 해석모델의 냉각해석 결과와 실차 방열시험 결과를 비교하였다. 이 연구를 통해 휠로더 흡배기구 단순화 해석기법의 적용 가능성을 확인하였으며 냉각성능 평가 및 개선 연구를 효과적으로 수행할 수 있는 기반을 마련하였다.

• 대한기계학회논문집B
• /
• 제26권6호
• /
• pp.842-849
• /
• 2002

The present study showed that a quantitative analogy of the fully developed laminar flows inorthogonally rotating rectangular ducts and stationary curved rectangular ducts of arbitrary aspect ratio could be established. In order to clarify the similarity of the two flows, the dimensionless parameters $K_{LR}$ =Re/√Ro and Rossby number Ro= $w_{m}$/$\Omega$d in a rotating strait duct were used as a set corresponding to Dean number $K_{LC}$ =Re/√λand curvature ratio λ=R/d in a stationary curved duct. Under the condition that the value of Rossby number and curvature ratio was large enough, the flow field satisfied the ‘asymptotic invariance property’: there were strong quantitative similarities between the two flows such as friction factors, flow patterns, and maximum axial velocity magnitudes for the same values of $K_{LR}$ and $K_{LC}$ .

• 한국추진공학회지
• /
• 제15권4호
• /
• pp.1-10
• /
• 2011

본 논문에서는 가스터빈 유로의 열유동 환경을 개선하기 위해 끝벽면의 형상에 대한 최적화를 수행하였으며, 비축대칭 끝벽면을 이용한 방법을 적용하였다. 터빈 유로를 모사하기 위해 $90^{\circ}$ 곡관을 이용하였다. 터빈 유로에서의 전압력 손실과 유로 끝벽면에서의 열전달 계수를 최소화하는 비축대칭 끝벽면형상 도출을 연구의 목적으로 하였으며, 최적화 과정의 효율성을 위해 근사 최적화 기법을 적용하였다. 연구결과를 통해, 최적화된 비축대칭 끝벽면에 의한 상당한 공력열환경 개선을 확인할 수 있었다.