• 한국도로학회논문집
• /
• 제18권1호
• /
• pp.73-83
• /
• 2016

PURPOSES : The purpose of this study is to develop a method for improving the accuracy of analysis results obtained from a two-dimensional (2-D) numerical analysis model of continuously reinforced concrete pavement (CRCP). METHODS : The analysis results from the 2-D numerical model of CRCP are compared with those from more rigorous three-dimensional (3-D) models of CRCP, and the relationships between the results are recognized. In addition, the numerical analysis results are compared with the results obtained from field experiments. By performing these comparisons, the calibration factors used for the 2-D CRCP model are determined. RESULTS : The results from the comparisons between 2-D and 3-D CRCP analyses show that with the 2-D CRCP model, concrete stresses can be overestimated significantly, and crack widths can either be underestimated or overestimated by a slight margin depending on the assumption of plane stress or plane strain. The behaviors of crack width in field measurements are comparable to those obtained from the numerical model of CRCP. CONCLUSIONS : The accuracy of analysis results from the 2-D CRCP model can be improved significantly by applying calibration factors obtained from comparisons with 3-D analyses and field experiments.

• 한국해안·해양공학회논문집
• /
• 제20권4호
• /
• pp.363-371
• /
• 2008

본 연구에서는 투과성잠제 주변의 파동장 해석을 위한 2-D 수치해석기법과 3-D 수치해석기법에 의한 결과를 비교하기 위하여 투과성구조물에 의한 유체저항(관성저항, 층류저항 및 난류저항)을 고려할 수 있는 수치해석기법을 이용하고, 난류모델로서 LES 모델을 도입하여 기존에 수행되었던 수리모형실험과의 비교를 통하여 검증하였다. 수치해석결과로부터 투과성잠제의 배후에서 2-D해석에 의한 결과가 3-D해석의 경우보다 높은 파고분포를 나타내었으며, 잠제 주변의 평균류에 대해서도 비교, 논의하였다.

• 한국수자원학회:학술대회논문집
• /
• 한국수자원학회 2007년도 학술발표회 논문집
• /
• pp.1287-1292
• /
• 2007

Recently, the frequency of unexpecting heavy rains has been increased due to abnormal climate and extreme rainfall. There was a limit to analyze 1D or 2D stream flow that was applied simple momentum equation and fixed energy conservation. Therefore, hydrodynamics flow analysis in rivers has been needed 3D numerical analysis for correct stream flow interpretation. In this study, CFD model on FLOW-3D was applied to stream flow analysis, which solves three dimenson RANS(Reynolds Averaged Navier-Stokes Equation) control equation to find out physical behavior and the effect of hydraulic structures. Numerical simulation accomplished those results was compared by using turbulence models such as ${\kappa}-{\varepsilon}$, RNG ${\kappa}-{\varepsilon}$ and LES. Those numerical analysis results have been illustrated by the turbulence energy effects, velocity of flow distributions, water level pressure distributions and eddy flows around the piers at Jangwall bridge in urbarn stream.

• 한국분말재료학회지
• /
• 제9권4호
• /
• pp.245-250
• /
• 2002

In this paper we presented numerical method for the simulation of powder injection molding filling process, which is one of the key processes in powder injection molding. Rheological properties of powder binder mixture such as slip phenomena and yield stress were introduced into the numerical analysis model of powder injection molding filling simulation. Numerical model can be classified into two types. One is 2.5D model which can be introduced to a arbitrary thin geometry and the other is full 3D model which can be applied to a general 3D shape. For 2.5D model we showed the validity of our CAE system with several verification examples. Finally we suggested flow analysis model for 3D powder injection molding filling simulation.

• 한국철도학회논문집
• /
• 제9권2호
• /
• pp.180-186
• /
• 2006

In this study, a large-scale laboratory model test, 2-D and 3-D numerical analyses were conducted to verify the reinforcement effect by utilizing geotextile bag on the railway roadbed. Static loading which simulated train load was applied on the geotextile bag-reinforced railway roadbed and also unreinforced railway roadbed, Computer program named Pentagon which is a part of FEM programs was used in the numerical analysis. Based on the results of laboratory test, 2-D and 3-D numerical analyses, the effect of load distribution and settlement reduction was found to be depending on the geotextile characteristics, tensile strength of geotextite, and interface friction angle between geotextile bags. In general, the result of 2-D and 3-D numerical analyses shows lower value than that of laboratory test. Also, the result of 3-D numerical analyses shows lower value than that of 2-D numerical analyses because of its stress transfer effect.

• 대한토목학회논문집
• /
• 제34권3호
• /
• pp.859-871
• /
• 2014

본 연구에서는 염분과 온도차에 의한 밀도류를 해석하기 위하여 기존의 3차원 파동장 모델(LES-WASS-3D ver. 1.0)을 토대로 염분과 온도에 관한 상태방정식 및 3차원 이류-확산 방정식을 도입하여 새로운 수치모델(LES-WASS-3D ver. 2.0)을 개발하였다. 새롭게 개발한 수치모델의 적용성을 검토하기 위하여 기존의 수리모형실험결과와 비교 분석하였다. 그 결과, 이류-확산하는 해수의 형태 및 연직 염분농도 뿐만 아니라 방출하는 온수의 유속 및 온도를 매우 잘 재현하는 것으로 나타났다. 이로써 본 연구에서 개발한 수치모델의 타당성 및 유효성이 검증되었다.

• Journal of Advanced Research in Ocean Engineering
• /
• 제1권2호
• /
• pp.115-133
• /
• 2015

This paper describes an approach for the numerical analysis of container ship slamming and whipping and various parameters that influence slamming and whipping. For validation purposes, the numerical analysis results were compared with experimental results obtained as part of the Wave-Induced Loads on Ships Joint Industry Project. Water entry problems for two-dimensional (2D) sections were first solved using a 2D generalized Wagner model (GWM) for various drop conditions and geometries. As the next step, the hydroelastic numerical analysis of a 10,000-TEU container ship subjected to slamming and whipping loads in waves was performed. The analysis method used is based on a fully coupled model consisting of a three-dimensional (3D) Rankine panel model, a 3D finite element model (FEM), and a 2D GWM, which are strongly coupled in the time domain. Parametric studies were carried out in both numerical and experimental tests with various forward speeds, wave heights, and wave periods. The trends observed and the validity of the numerical analysis results are discussed.

• Steel and Composite Structures
• /
• 제15권3호
• /
• pp.247-266
• /
• 2013

This paper presents a comparison of results obtained by a newly developed numerical model for predicting the behaviour of structures under fire with experimental study carried out on heated and simply supported steel beam elements. A newly developed numerical model consists of three submodels: 3D beam model designed for calculating the inner forces in the structure, 2D model designed for calculation of stress and strain distribution over the cross section, including the section stiffness, and 3D transient nonlinear heat transfer model that is capable of calculating the temperature distribution along the structure, and the distribution over the cross section as well. Predictions of the calculated temperatures and vertical deflections obtained by the numerical model are compared with the results of the inhouse experiment in which steel beam element under load was heated for 90 minutes.

• Wind and Structures
• /
• 제7권1호
• /
• pp.13-28
• /
• 2004

A method of numerical analysis without conducting 3D wind tunnel model tests was examined in our previous study for predicting vortex-induced oscillation of bridge girders with span-wise varying geometry. The aerodynamic damping forces measured for plural wind tunnel 2D models were used in the analysis. A further study was conducted to examine the precision of solution obtained by this method. First, the responses of vortex-induced oscillation of two rocking models and a taut-strip bridge girder model with span-wise varying geometry were measured. Next, the responses of these models were numerically analyzed by means of this method, and then a comparison was made between the obtained $Vr-A-{\delta}_a$ contour diagram of each 3D model in the wind tunnel test and the diagram in the numerical analysis. Since close correlations were observed between each two $Vr-A-{\delta}_a$diagrams obtained in the model test and in the analysis in cases where the 3D model did not have strong three-dimensionality, our findings revealed that the predicted solution proved to be reasonably accurate.

• 터널과지하공간
• /
• 제22권2호
• /
• pp.93-105
• /
• 2012

균열암반의 등가역학적 물성을 수치해석적으로 결정할 때 2차원 및 3차원 해석을 비교하였다. 수직균열모델과 암반균열망(DFN) 모델이 균열암반의 형상으로 이용되었으며 3차원 모델으로부터 다양한 방향으로 2차원 모델을 절단하여 역학적 물성을 비교하였다. 본 연구의 지질데이터는 영국 셀라필드 지역의 자료를 기본으로 사용하였다. 직교균열모델에서는 컴플라이언스텐서의 변환을 이용한 해석적 방법이 물성결정을 위해 이용되었으며 암반균열망모델에서는 수치실험이 실시되었다. 2차원 모델에서는 균열이 항상 모델평면과 직교한다고 가정하기 때문에 탄성계수는 항상 3차원보다 크게 계산이 되었다. 2차원 해석에서의 포아송비는 3차원 해석보다 큰 값을 나타내는 경향이 있었으나 반대의 경향도 관찰되었다. 본 논문은 3차원 형상을 단순화시켜 사용하는 2차원 해석의 한계를 정량적으로 고찰하였다는데 의의가 있다.