• 항공우주기술
• /
• 제7권2호
• /
• pp.88-94
• /
• 2008

본 연구에서는 통신해양기상위성 형상을 갖고 훨모멘텀 제어를 위해 추력기를 사용할 때 발생되는 3축 궤도병진 운동에 관하여 분석하였다. 또한, 통신해양기상위성은 롤/요 훨모멘텀 제어를 위해 사용되는 추력기의 성능 감소를 균일하게 하기 위해 주기적으로 조합군을 변경하도록 설계하였기 때문에 조합군 변경시에 발생되는 3축 궤도병진 속도 차이가 발생하게 된다. 따라서 본 연구에서는 COMS 추력기 조합군 변경시 발생되는 3축 궤도병진 속도를 최적화하였다.

• 소음진동
• /
• 제8권1호
• /
• pp.81-86
• /
• 1998

A 500Wh class high-speed Flywheel Energy Storage System (FESS) driven by a built-in BLDC motor/generator has been designed, which runs from 30000 to 60000rpm nominally. Due to the motor/generator inside, the flywheel rotor made of composites supported by PM/EM hybrid bearing system has a shape of bell or pendulum and thus requires accurate rotordynamic analysis and prediction of its dynamic behavior to secure the operating reliability. Rotordynamic analyses of the flywheel rotor-bearing system revealed that the bell shaped rotor has two conical rigid-body modes in the system operating range and the first conical mode, of which nodal point lies in the radial EM bearing position, can adversely affect the dynamic response of the rotor at the corresponding critical speed. To eliminate the possibility of wild behavior of the rotor, two guide bearings are adopted at the upper end of the rotor and motor/generator. It was also revealed that the EM bearing stiffness if 0.5~1.0E+6 N/m and damping of 2000 Ns/m are favirable for smooth operation of the system around the 2nd critical speed.

• 전자공학회논문지SC
• /
• 제46권2호
• /
• pp.28-35
• /
• 2009

이동 로봇의 요소기술로 위치추정 기술은 로봇의 위치 판별과 사용자가 원하는 위치로 주행하기 위해 반드시 필요한 기술이다. 휠 구동을 기반으로 하는 로봇의 위치추정 방법은 오도메터리 정보를 이용한 기술이다. 그러나 오도메터리 정보를 이용한 위치추정은 이동로봇이 주행하는 동안 휠과 주행 바닥면 사이에서 슬립현상의 발생으로 실제 위치 차이가 발생하고 정량적인 오차 값 확인이 쉽지 않다. 본 연구에서는 이 문제를 해결하기 위해 오도메터리와 관성센서를 이용하여 위치추정 오차를 최소화하는 방법을 제시한다. 또한 관성센서가 영상을 이용한 SLAM에서도 위치오차를 줄일 수 있는 기법을 제시한다.

• 한국자동차공학회논문집
• /
• 제22권3호
• /
• pp.12-18
• /
• 2014

This paper describes about the development of new concept's rear wheel guards for the reduction of Road Noise in the passenger vehicle using test. The new wheel guards are proposed by various frequency chamber concept and different textile layers concept. Two wheel guards were verified by small cabin resonance test and vehicle test. Through new developing process without vehicle test, Result of road noise will be expected when new concepts and materials of wheel guard is applied into automotive vehicle. As a result of the application of Aimed Helmholtz and Multi-layers concept, this paper classifies the road noise, cost and weight are reduced by new concepts and the solutions are adopted into the 2 cars.

• 한국자동차공학회논문집
• /
• 제10권2호
• /
• pp.166-173
• /
• 2002

The wheel bearing hub unit is developed type of wheel bearing unified with the hub parts. It has advantage of reducing the weight and the number of components. And, it also improves uniformity of manufacturing quality, In order to design the wheel bearing hub units, many techniques are used such as load analysis, structure analysis and bearing characteristics analysis and so forth. These techniques need highly accurate load conditions founded on service conditions. In this study, to design the wheel bearing hub units used widespread in passenger cars, the service load was measured through driving tests on the public roads and in the special events. The public roads are classified into highway, intercity road, rural road, urban road, and unpaved road so as to know what the characteristics of the road loads are. The results of the tests showed that the wheel force was relative to the lateral acceleration, and also could be calculated from the lateral acceleration. The lateral acceleration was measured from 0.0G to 0.6G in general driving on the public roads, with different distributions in each road type. In special events, the maximum lateral acceleration was measured from 0.8G to 1.3G.

• 플랜트 저널
• /
• 제6권2호
• /
• pp.62-69
• /
• 2010

The stability of coal pulverizer in the 800 MW coal-fired plants is vital to maintain their performance. Thus, this study analyzed the uneven abrasion of the deflector and coal spillage due to the air velocity maldistribution in the vane wheel of a bowl-type pulverizer as it is a possible cause for problems of facility using pulverized coal. In addition, air flow in the underbowl of a bowl-type pulverizer was studied to check air velocity maldistribution in the vane wheel using numerical method. In an attempt to correct the maldistribution of air velocity, air flow of the modified duct vane was studied as enlarging the length of the duct vanes installed at the air inlet duct of the pulverizer and increasing the angle of inclination. It was found that modified duct vane make the velocity distribution at the vane wheel uniform. formed by the duct vanes installed at the air inlet duct of the pulverizer and swirling flow is the major factor in making the velocity distribution of vane wheel exit uniform. This can prevent the uneven abrasion of the deflector, which is one of the components inside the pulverizer and coal spillage.

• 천문학회보
• /
• 제41권1호
• /
• pp.74.1-74.1
• /
• 2016

미국 텍사스 주 맥도날드 천문대에 위치한 2.1m 망원경에 부착된 SQUEAN (SED Camera for QUasars in EArly uNiverse)은 2010년부터 운용되고 있는 CQUEAN을 바탕으로 개발된 적외선 영역 광학기기이다. 20개의 필터 장착이 가능한 필터 휠 제어 시스템을 가지고 있는 SQUEAN 시스템은 SMOP (SQUEAN Main Observation software package), KFC82 (KHU Filter wheel Control software package for McDonald 82 inch Telescope), KAP82 (KHU Auto-guiding software Package for McDonald 82 inch Telescope) 등으로 구성되어 있다. 그러나 대형 필터 휠을 제어하는 모터의 토크부족과 감속기의 백래시(Backlash)의 영향으로 오프셋의 오차가 커서 초기위치의 재설정 없이 하룻밤 이상 관측을 지속하는데 어려움이 있었다. 토크가 크고 인코더가 장착된 모터 교체와 제어 프로그램 등을 변경하고, 백래시의 영향을 최소화할 수 있도록 소프트웨어로 보정하였다. 또한, SMOP로부터 네트워크 통신을 통해 초기화용 필터 마스크(Initial Filter Mask:IFM)를 제작하여 돔 플랫 이미지에서 정확한 필터의 위치를 측정하는 기능을 도입하였다. 이 발표에서는, 개선된 하드웨어 및 소프트웨어의 내용과 테스트한 결과에 대해 보여준다.

• 한국지반신소재학회논문집
• /
• 제2권3호
• /
• pp.39-46
• /
• 2003

국내 도로포장의 주요 파손형태는 주변환경 및 반복교통하중 조건에 의한 소성변형, 피로균열, 반사균열, 온도균열 등이 있는데, 포장이 설계수명에 도달하기 이전에 주로 발생하며 이로 인한 도로포장의 유리관리에 막대한 국가예산이 낭비되고 있는 실정이다. 본 연구는 토목섬유를 보강한 아스팔트 포장 시스템을 평가하는 것으로 이를 위해 아스팔트 포장 소성변형에 대한 토목섬유의 보강효과를 분석하고자 휠트래킹 시험을 수행하였으며, 토목섬유 보강에 따른 토목섬유와 아스팔트 혼합물의 거동특성을 고찰하였다.

• 한국기계가공학회지
• /
• 제21권3호
• /
• pp.77-85
• /
• 2022

In this study, to diagnose the grinding state of a micro drill bit, a sensor attachment location was selected through random vibration analysis of the grinding unit of the micro drill-bit grinding system. In addition, the vibration data generated during the drill bit grinding were collected from the grinding unit for the grinding wheels under the steady and worn conditions, and data feature extraction and dimension reduction were performed. The wear of the micro-drill-bit grinding wheel was diagnosed by applying KNN, a machine-learning algorithm. The classification model showed excellent performance, with an accuracy of 99.2%. The precision, recall and f1-score were higher than 99% in both the steady and wear conditions.

• Tribology and Lubricants
• /
• 제39권3호
• /
• pp.94-101
• /
• 2023

Automotive wheel bearings are a critical component of vehicles that support their weight and facilitate rotation. Life and stiffness are significant performance characteristics of wheel bearings. Designing wheel bearings involves finding optimal design variables that satisfy both performances. CO₂ emission reduction and fuel efficiency regulations attribute to the recent increase in design requirements for lightweight and compact automotive parts while maintaining performance. However, achieving a design that maintains performance while reducing weight poses challenges, as performance and weight are generally inversely proportional. In this study, we perform design optimization of automotive wheel bearings considering life and stiffness. We develop a program that calculates the basic rated life and modified rated life based on international standards for evaluating the life of wheel bearings. We develop a regression equation using regression analysis to address the time-consuming stiffness analysis during repetitive analysis. We perform ANOVA and main effect analyses to understand the statistical characteristics of the developed regression equation. Furthermore, we verify its reliability by comparing the predicted and test results. We perform design optimization using the developed life prediction program, stiffness regression equation and weight regression equation. We select bearing specifications and geometry as design variables, weight as the cost function, and life and stiffness as constraints. Through design optimization, we investigate the influence of design variables on the cost function and constraints by comparing the initial and optimal design values.