Seismic reflection surveying is one of the most widely used and effective techniques for coal seam structure delineation and risk mitigation for underground longwall mining. However, the ability of the method can be compromised by the presence of volcanic cover. This problem arises within parts of the Bowen and Sydney Basins of Australia and seismic surveying can be unsuccessful. As a consequence, such areas are less attractive for coal mining. Techniques to improve the success of seismic surveying over basalt flows are needed. In this paper, we use elastic wave-equation-based forward modelling techniques to investigate the effects and characteristics of seismic wave propagation under different settings involving changes in basalt properties, its thickness, lateral extent, relative position to the shot position and various forms of inhomogeneity. The modelling results suggests that: 1) basalts with high impedance contrasts and multiple flows generate strong multiples and weak reflectors; 2) thin basalts have less effect than thick basalts; 3) partial basalt cover has less effect than full basalt cover; 4) low frequency seismic waves (especially at large offsets) have better penetration through the basalt than high frequency waves; and 5) the deeper the coal seams are below basalts of limited extent, the less influence the basalts will have on the wave propagation. In addition to providing insights into the issues that arise when seismic surveying under basalts, these observations suggest that careful management of seismic noise and the acquisition of long-offset seismic data with low-frequency geophones have the potential to improve the seismic results.
Journal of the Korean Society of Clothing and Textiles
/
v.29
no.12
s.148
/
pp.1595-1607
/
2005
Three-dimensional(3-D) body scanners used to capture anthropometric measurements are now becoming a common research tool far apparel. This study had two goals, to test the accuracy and reliability of 3-D measurements of dynamic postures, and !o analyze the change in upper body surface measurements between the standard anthropometric position and various dynamic positions. A comparison of body surface measurements using two different measuring methods, 3-D scan measurements using virtual tools on the computer screen and traditional manual measurements for a standard anthropometric posture and for a posture with shoulder flexion were $-2\~20mm$. Girth items showed some disagreement of values between the two methods. None of the measurements were significantly different except f3r the neckbase girth for any of the measuring methods or postures. Scan measurements of the upper body items showed significant linear surface change in the dynamic postures. Shoulder length, interscye front and back, and biacromion length were the items most affected in the dynamic postures. Changes of linear body surface were very similar for the two measuring methods within the same posture. The repeatability of data taken from the 3-D scans using virtual tools showed satisfactory results. Three times repeated scan measurements f3r the scapula protraction and scapula elevation posture were proven to be statistically the same for all measurement items. Measurements from automatic measuring software that measured the 3-D scan with no manual intervention were compared with the measurements using virtual tools. Many measurements from the automatic program were larger and showed quite different values.
In this research, based on the fact that spatial ability is important for the achievement in the STEM fields, and technological innovation, Purdue Spatial Visualization Test-Rotation has been used to investigate engineering freshmen's spatial ability and gender differences. Students who have taken advanced mathematics courses in high school(those who have taken type B math test in Korean SAT test) and students with general math courses(those who have taken type A in Korean SAT-Math test) are included in this study to find out the relationship between mathematics achievement and spatial ability. Finding out the strategies taken by students was another aim of this study. This strategic differences between high achievers and lower achievers, male and female students were analyzed from students' self report. Spatial ability test score was highest in the SAT-Math type B male students, decreased in the order of type A male students, type B female students, and lastly type A female students. There was no substantial difference between second and third groups. In each group, male students' average score was 8~10% higher than female students, which affirms 2015's results. The correlation between spatial ability and mathematics achievement was negligible in each group, but male students' math score and spatial ability score were higher than that of female students. This can be interpreted that there is some correlation between these two. Strategic choices can vary in the continuous spectrum with analytic method and holistic method at both ends. From students' self report, using Mann-Witney test, it turned out that there exists strategic differences between male and female students. Male students have a tendency to use holistic strategy more often than female students. I also found that the strategy choice did not vary greatly among all score groups. For the perfect score groups, both female and male students used holistic strategy most frequently. For low achieving groups, there is an evidence that these students overuse one method compared to average or high achieving groups, which turned out to be less effective. Based on these, I suggest that low achieving students need to have more chances to adopt efficient strategies and to practice challenging problems to improve their spatial abilities.
Purpose: Recently, two tests are commercially available for the identification of latent tuberculosis infection (LTBI): tuberculin skin test (TST) and interferon-${\gamma}$ release assay (IGRA). Due to its false positiveness, TST tends to be preferred by IGRA until now. In our study, we simultaneously performed both TST and QuantiFERON$^{(R)}$-TB Gold In-Tube (QFT-GIT) and compared their results. Methods: TST and QFT-GIT were done for the diagnosis of LTBI among children who visited pediatric out-patient clinic at St. Vincent's Hospital, The Catholic University of Korea from February of 2007 to May of 2008. The study group was stratified into two groups in terms of whether there was intrafamilial contact or not. Results: Out of total 35 children, 29 were tuberculosis (TB)-exposed cases and the remainders were diagnosed as clinical pulmonary TB. Among these 29 children, TST was positive 38.9% (7/18) for the intrafamilial and 45.5% (5/11) for the nonintrafamilial, and at the same time, the result for QFT-GIT was positive 5.6% (1/18) and 9.1% (1/11), respectively which implies that TST was more sensitive than QFT-GIT. Among 29 TB-exposed cases, 26 initially went through TST and QFTGIT together on their first visit to out-patient clinic, and 15 continued the follow-up tests. Out of total 41 cases collected, the agreement (known as kappa value) was 0.063 which was relatively low. Including 6 cases with pulmonary TB who were all positive for TST and only 5 being positive for QFT-GIT, the final kappa value was 0.334. Conclusion: In our study, the agreement for TST and QFT-GIT was low, and the majorities were almost the cases of positive TST. In current situation with lacking a gold standard test and limited data on children to adolescents, this result is quite alarming that the recent trend tends to replace TST by QFT-GIT when diagnosing LTBI.
현재 우리 나라가 사용하고 있는 표준시는 I-시간이다. 이 표준시 사용에 대해 일부 이견이 있어, 우리 나라의 표준시 제도를 확립하기 위해 세계 각국의 표준시의 운용 상황을 분석 검토함으로서 우리나라는 현재 사용 중인 I-시간을 계속적으로 사용하는 것이 타당한 것으로 다음과 같은 결론을 얻을 수 있었다. 1) 세계에서 복수 표준시를 운용하고 있는 나라(러시아 등 9개국)는, 표준시 적용 지역을 태양시에 정확하게 맞추어 결정할 수 있을 것임에도, 3개국만 표준시가 태양시에 거의 일치할 뿐 나머지 6개국은 모두 태양시보다 표준시를 앞세워 적용하고 있다. 2) 세계 15대 대 영토국 중 단일표준시를 운용하고 있는 나라(중국 등 6개국) 중에서 3개국이 대체로 표준시가 태양시에 일치할 뿐이고, 나머지 3개국은 표준시를 태양시보다 $1{\sim}2$시간 이상이나 앞세워 적용하고 있다. 3) 전 세계의 145개 주요 단일 표준시 사용국 중 약 5%(중동의 지중해 연안국들과 동유럽의 일부 국가들) 정도에서 표준시를 태양시보다 30분 정도 늦춰 적용할 뿐이고, 태양시와 비슷하게 운용하는 나라는 약 56%, 표준시를 30분 이상 앞세워 적용하고 있는 나라는 약 39% 정도로서 대체로 태양시보다 빠른 표준시를 긍정적으로 받아들이고 있다. 4) 캐나다와 미국의 경우는 각 주에서 정한 표준시와는 다르게 운영하고 있는 지방들이 있는데, 이들 모두가 지리적인 위치로 보아 태양시보다 표준시가 어느 정도 빠르게 운영되도록 조정한 경우들이다. 5) 세계에서 UTC와 비 정수 시간차의 표준시를 운용하는 지역과 국가는 7개소 정도이다. 이들 중 표준시를 태양시에 맞추어 설정한 경우가 6개소이고, 지리적인 위치로 보아 표준시와 태양시가 일치할 수 있는데도 표준시를 30분 정도를 빠르게 운용하기 위해 조정한 경우가 1개소이다. 6) 세계에서 서머타임을 적용하고 있는 최저위도 국가는 북반구에서는 북회귀선에 걸쳐 있는 Mexico와 Cuba, 남반구에서는 Brazil의 남회귀선에 걸쳐 있는 남반부인데 이들은 모두 태양시와 일치하는 표준시를 운용하는 나라들이다. 한편 서머타임을 적용하고 있지 않는 최고위도 국가는 북반구에서는 Iceland, 남반구에서는 Argentina인데, 이 두 나라는 모두 이미 표준시를 태양시보다 1시간 이상 빠르게 적용하고 있는 나라들이다. 7) 복수 표준시간을 운용하고 있는 Canada와 미국에서는 국가적으로는 서머타임을 운용하고 있는데도 서머타임을 운용하고 있지 않는 주가 Canada에는 1개주, 미국에는 3개 주가 있는데, 이들은 모두 표준시가 태양시보다 30분${\sim}$1시간 정도 빠르게 적용되고 있는 곳이다. 8) 세계의 많은 나라가 표준시를 태양시보다 30분${\sim}$1시간 또는 그 이상까지도 빠르게 적용하고 있다는 사실, 그리고 세계의 많은 나라에서 서머타임을 시행하고 있다는 사실을 보면 태양시보다 표준시를 어느 정도 빠르게 적용해 생활하는 것은 인간 생체리듬에 악영향을 미치지 않으면서 오히려 시간 이용을 효율화하는 장점이 있는 것으로 판단된다. 9) 현재 우리나라는 경도 $135^{\circ}E$를 기준으로 하는 I-시간을 사용하고 있으면서 I-시간대역의 서쪽경계에 위치하여 태양시보다 표준시가 30분 정도 빠르다. 이는 한국인의 생체리듬에 결코 나쁜 영향을 주지 않으며, 오히려 시간을 효율적으로 사용할 수 있는 장점으로 작용하고 있는 것으로 판단된다. 아울러 여름철에 일광절약시간(서머타임)제의 필요성을 완화시켜줌으로서 표준시를 안정적으로 운용하는데 크게 기여하고 있다. 이는 표준시를 UTC와 정수시간차를 유지하면서 안정적으로 운영하려는 세계 각국의 표준시 운영 경향과도 일치하고 있다. 10) 우리나라가 사용하는 I-시간이 우리에게 이상과 같은 장점을 가지고 있음에도 불구하고 이 I-시간이 일제의 잔재라거나 또한 한국인의 생체리듬에 해롭다는 이유를 들어 우리 나라의 표준시를 경도 $127.5^{\circ}W$ 기준의 H'시간으로 변경시킨다면UTC와의 8시간 30분차 시간을 운영하게 됨으로서 국제화 시대를 사는데 큰 불편을 초래할 뿐만 아니라, 추가적으로 서머타임제를 도입하게 되는 등 커다란 부작용을 겪게 될 것이다.
The calculation method of infiltration loss in greenhouse has different ideas in each design standard, so there is a big difference in each method according to the size of greenhouses, it is necessary to establish a more accurate method that can be applied to the domestic. In order to provide basic data for the formulation of the calculation method of greenhouse heating load, we measured the infiltration rates using the tracer gas method in plastic greenhouses equipped with various thermal curtains. And then the calculation methods of infiltration loss in greenhouses were reviewed. Infiltration rates of the multi-span and single-span greenhouses were measured in the range of $0.042{\sim}0.245h^{-1}$ and $0.056{\sim}0.336h^{-1}$ respectively, single-span greenhouses appeared to be slightly larger. Infiltration rate of the greenhouse has been shown to significantly decrease depending on the number of thermal curtain layers without separation of single-span and multi-span. As the temperature differences between indoor and outdoor increase, the infiltration rates tended to increase. In the range of low wind speed during the experiments, changes of infiltration rate according to the outdoor wind speed could not find a consistent trend. Infiltration rates for the greenhouse heating design need to present the values at the appropriate temperature difference between indoor and outdoor. The change in the infiltration rate according to the wind speed does not need to be considered because the maximum heating load is calculated at a low wind speed range. However the correction factors to increase slightly the maximum heating load including the overall heat transfer coefficient should be applied at the strong wind regions. After reviewing the calculation method of infiltration loss, a method of using the infiltration heat transfer coefficient and the greenhouse covering area was found to have a problem, a method of using the infiltration rate and the greenhouse volume was determined to be reasonable.
The calculation method of ground heat exchange in greenhouses has different ideas in each design standard, so there is a big difference in each method according to the size of greenhouses, it is necessary to establish a more accurate method that can be applied to the domestic. In order to provide basic data for the formulation of the calculation method of greenhouse heating load, we measured the soil temperature distribution and the soil heat flux in three plastic greenhouses of different size and location during the heating period. And then the calculation methods of ground heat exchange in greenhouses were reviewed. The soil temperature distributions measured in the heating greenhouse were compared with the indoor air temperature, the results showed that soil temperatures were higher than room temperature in the central part of greenhouse, and soil temperatures were lower than room temperature in the side edge of greenhouse. Therefore, it is determined that the ground heat gain in the central part of greenhouse and the perimeter heat loss in the side edge of greenhouse are occurred, there is a difference depending on the size of greenhouse. Introducing the concept of heat loss through the perimeter of building and modified to reflect the size of greenhouse, the calculation method of ground heat exchange in greenhouses is considered appropriate. It was confirmed that the floor heat loss measured by using soil heat flux sensors increased linearly in proportion to the temperature difference between indoor and outdoor. We derived the reference temperature difference which change the direction of ground heat flow and the perimeter heat loss factor from the measured heat flux results. In the heating design of domestic greenhouses, reference temperature differences are proposed to apply $12.5{\sim}15^{\circ}C$ in small greenhouses and around $10^{\circ}C$ in large greenhouses. Perimeter heat loss factors are proposed to apply $2.5{\sim}5.0W{\cdot}m^{-1}{\cdot}K^{-1}$ in small greenhouses and $7.5{\sim}10W{\cdot}m^{-1}{\cdot}K^{-1}$ in large greenhouses as design standard data.
Natural and anthropogenic factors cause forest types to continuously change. Since the ratio of forest area by forest type is important information for identifying the characteristics of national forest resources, an accurate understanding of the prospect of forest type change is required. The study aim was to use National Forest Inventory (NFI) time-series data to understand the characteristics of forest type change and to estimate future prospects of nationwide forest type change. We used forest type change information from the fifth and seventh NFI datasets, climate, topography, forest stand, and disturbance variables related to forest type change to analyze trends and characteristics of forest type change. The results showed that the forests in Korea are changing in the direction of decreasing coniferous forests and increasing mixed and broadleaf forests. The forest sites that were changing from coniferous to mixed forests or from mixed to broadleaf forests were mainly located in wet topographic environments and climatic conditions. The forest type changes occurred more frequently in sites with high disturbance potential (high temperature, young or sparse forest stands, and non-forest areas). We used a climate change scenario (RCP 8.5) to establish a forest type change model (SVM) to predict future changes. During the 40-year period from 2015 to 2055, the SVM predicted that coniferous forests will decrease from 38.1% to 28.5%, broadleaf forests will increase from 34.2% to 38.8%, and mixed forests will increase from 27.7% to 32.7%. These results can be used as basic data for establishing future forest management strategies.
Kim, Juhan;Kim, Dong Hwi;Lim, Jae-Hwan;Jang, Hyunwoong;Kim, Young Wook
Journal of the Korean Orthopaedic Association
/
v.54
no.3
/
pp.227-236
/
2019
Purpose: To evaluate the results of tibial lateral plateau fractures using arthroscopic-assisted reduction and internal fixation without cortical window or bone grafts. Materials and Methods: From March 2009 to March 2017, 27 patients with Schatzker type II tibial plateau fractures with articular depression and displacement over 5 mm on a computed tomography (CT) scan, who were treated with arthroscopic reduction and internal fixation and followed-up for at least 18 months, were enrolled in this study. Under arthroscopic guidance, the depressed fracture fragment was reduced using a freer and fixed with 5.0 or 6.5 mm cannulated screws through the inframeniscal portal without a cortical window or bone graft. The clinical and radiological results were evaluated using a Rasmussen system. Second look arthroscopy was performed in thirteen patients during the implant removal operation. Results: All fractures healed completely with a mean union time of 8.7 weeks (range from 8 to 12 weeks). Twenty four patients had good to excellent clinical results and 25 patients had good to excellent radiological results according to the Rasmussen classification. A well-healed articular surface with fibrocartilage was also found in 13 cases with second look arthroscopy. The 8 cases on CT scan at outpatient department follow-up showed bone union without bone grafting. Conclusion: Arthroscopic-assisted fixation of tibial lateral plateau fractures is a useful method without a cortical window or bone graft that produces good clinical results.
This study was done to analyze the contents of minerals and vitamins to compare the measured values of minerals, vitamins with labeled values of them in food labeling and to investigate the ratio of measured values to labeled values in 437 specimen with minerals and vitamins - fortified commercial beverages and liquid teas. Content of calcium and sodium in samples after microwave digestion was analyzed with an ICP-OES (Inductively Coupled Plasma Optical Emission Spectrometer) and vitamins were determined using by HPLC (High Performance Liquid Chromatography). The measured values of calcium were ranged 80.3~142.6% of the labeled values in 21 samples composed calcium - fortified commercial beverages and liquid teas. In case of sodium, measured values were investigated 33.9~48.5% of the labeled values in 21 sports beverages. The measured values of vitamin C, vitamin $B_2$ and niacin were ranged 99.7~2003.6, 81.1~336.7, 90.7~393.2% of the labeled values in vitamins - fortified commercial beverages and liquid teas, 57, 12, 11 samples. To support achievement of the accurate nutrition label, there must be program and initiatives for better understanding and guidances on food labelling and nutrition for food manufacture.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.