• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.28 no.3
• /
• pp.259-266
• /
• 2015

In this paper, transverse shear spacing and effective depth of wide beams were considered as parameters to evaluate the shear capacity of wide beam according to transverse spacing of steel plates with openings in experimental way. The eight specimens were composed of: five specimens of shear reinforced by steel plates with openings and three non-reinforced specimens. Crack, failure mode, strain and load-displacement curve of specimens were analysed. Shear contribution of shear reinforcement is evaluated and maximum transverse spacing of shear reinforcement was proposed. Shear strength of the specimen that reinforced with three stirrup legs was higher than shear strength of the specimen that reinforced with two stirrup legs. And as the effective depth increased, shear strength was increased.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.14 no.2
• /
• pp.27-36
• /
• 2010

It is well known that the shear strength of an RC column subjected to a lateral force decreases with the increase of the displacement ductility of column. This decreasing rate of shear strength is quite dependent on the initial shear strength. Therefore, the evaluation of the initial shear strength is important to predict the shear strength with reasonable accuracy. The shear behavior is complex because many parameters, such as the sectional shape, aspect ratio, axial force, longitudinal bars and ductility, are mutually interactive. In this study, the initial shear strength has been investigated by experiments varying parameters such as the aspect ratios, void ratios, ratio of longitudinal bars and sectional types. A new empirical equation for the initial shear strength, considering the ratio of the longitudinal bars, has been proposed and its validity has been assessed.

• Tunnel and Underground Space
• /
• v.13 no.3
• /
• pp.169-179
• /
• 2003

Anisotropic shear strength of rock joints is studied based on the artificially fractured specimens using experimental and analytical methods. Series of direct shear tests are performed to obtain the strength, stiffness and friction angle of joints under various low normal stresses and shearing directions. The results of shear strength and stiffness show anisotropic value according to shearing direction under low normal stress specially less than 2.45 MPa. But, the effect of joint roughness on strength decreases with increasing normal stress. To estimate more effectively the peak shear strength under low normal stress, the modified Barton's equation is suggested.

• The Journal of the Petrological Society of Korea
• /
• v.28 no.2
• /
• pp.53-69
• /
• 2019

In the Jirisan area of the Yeongnam Massif, Korea, several ductile shear zones are developed within Precambrian gneiss complex (Jirisan metamorphic rock complex). The ductile shear zones have a general NS- and NNE-striking foliation with westward dipping directions. The foliation developed in the shear zones cut the foliation in gneiss complex. The stretching lineations are well developed in the foliated plane of the shear zone, showing ENE-trend with gentle plunging angle to the ESE direction. Within shear zone, several millimetric to centimetric size of porphyroclasts are deformed strongly as a sigmoid form by ductile shearing. The sigmoid patterns of porphyroclasts in the shear zones indicate the dextral shearing. The spatial distribution of ductile shear zone is characterized by the dominant NS- and NNE-striking dextral sense in the central and eastern regions respectively. In the western part, it develops in NE-striking dextral sense which is the general direction of the Honam shear zone. The U-Pb concordant ages obtained from the two samples, the strongly sheared leucocratic gneiss, are $1,868{\pm}3.8Ma$ and $1,867{\pm}4.0Ma$, respectively, which are consistent with the U-Pb ages reported around the study area. We supposed that the ductile shearing in the study area is occurred about 230~220 Ma during late stage of the continental collision around Korea and is preceded by granitic intrusion related to subduction during 260~230 Ma, which are supported by compiling the age data from sheared gneiss, deformed mafic dyke intruded gneiss complex, and non-deformed igneous rocks.

• Journal of Korean Association for Spatial Structures
• /
• v.5 no.2 s.16
• /
• pp.65-71
• /
• 2005

The reinforced concrete becomes deteriorated. In strengthening of reinforced concrete structure, it is recently useing FRP. In research, flexural strengthening of reinforced concrete beam can be Efficient design. But shear srengthening og reinforced concrte beam can't be Efficient design by variable cause. The purpose of this study is to investigate the shear resisting effect of filling-up CFRP in reinforced concrete beams with web reinforced. Ten specimens were manufactured and tested. In the test result, it was analysis. The main variables in the test were a space of web reinforcement and a direction of CFRP.

• The Journal of the Petrological Society of Korea
• /
• v.18 no.4
• /
• pp.293-305
• /
• 2009

The Gilan-Cheongsong area, which is in contact with Yeongyang and Uiseong Blocks of Gyeongsang Basin, Korea, consists of Precambrian metamorphic rocks, Triassic Cheongsong granite, Cretaceous sedimentary rocks(Iljik, Hupyeongdong, Jeomgok Formations), and Cretaceous igneous rocks(andesite, quartz porphyry, felsite). In this area are developed faults trending in (W)NW, NNW, ENE, NS, (N)NE directions which are representative in the Gyeongsang Basin. We analyzed the geometric and kinematic characteristics of fracture systems to inquire into movement history and sense of these faults in this area. This study suggests that these faults were mainly strike-slip movement. The orientations of fracture sets show ENE, NNW, (W)NW, (N)NE, NS in descending order of frequency. Their prolongation presents (W)NW, NNW, ENE, (N)NE, NS in descending order of predominance, and also agrees with that of faults in this area. The development sequence and movement sense of fracture sets are summarized as follows; (1) (W)NW: dextral shearing $\rightarrow$ (2) (W)NW and NNW: conjugate shearing(the former: dextral, the latter: sinistral) $\rightarrow$ (3) NNW: dextral shearing $\rightarrow$ (4) (W)NW: sinistral shearing $\rightarrow$ (5) ENE: dextral shearing $\rightarrow$ (6) ENE and NS: conjugate shearing(the former: sinistral, the latter: dextral) $\rightarrow$ (7) (N)NE: sinistral shearing, and this result is closely associated with the development sequence and movement sense of faults developed in this area.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2011.04a
• /
• pp.648-651
• /
• 2011

본 논문에서는 3차원 섬유분포를 가정하여 고유동 섬유보강 시멘트 모르타르의 유동에 따른 섬유방향성변화를 해석적으로 파악해 보았다. 유동흐름은 평면상의 2차원 완전발달 전단흐름을 고려하였다. 유동에 따른 섬유의 회전운동은 섬유간의 상호 간섭효과를 무시한 Jeffery의 기본식에 근거하였다. 굳지 않은 섬유혼입 모르타르의 유동에 따른 섬유방향성 분포 변화를 흐름선과 동일 유동거리 상의 단면에 대해 파악하였다. 그 결과, 단면 내 위치에 따라서 섬유방향성 분포 변화가 크게 차이가 발생하는 것을 확인할 수 있었다. 또한 유동거리에 따른 단면상의 섬유방향성 분포는 초기 유동거리에서 분포 형상에 큰 변화가 발생하였고, 유동에 따라 섬유가 유동방향과 나란하게 놓이는 경향이 커지는 것을 확인할 수 있었다. 이러한 섬유방향성 변화의 예측은 섬유보강 시멘트 복합체의 인장특성에 예측하는데 유용하게 사용될 것이다.

• Journal of the Korean Wood Science and Technology
• /
• v.46 no.5
• /
• pp.425-436
• /
• 2018

This study was conducted to evaluate the planar (rolling) shear strength of OSB (oriented strand board) panels and domestic plywood through 5 point bending test method in ASTM D2718 standard. The test specimens were prepared in parallel and perpendicular direction to major axis (along the length of panels) and tested up to failure, and failure modes were also examined. From the test results, rolling shear strength were found to be $1.32{\sim}1.94N/mm^2$ in parallel to major axis, and $1.46{\sim}1.99N/mm^2$ in perpendicular to major axis respectively. Little difference was found between parallel and perpendicular direction of rolling shear strength. There were no statistically significant differences in rolling shear strength between Canadian OSB and domestic plywood in the parallel direction, and between Chilean OSB and domestic plywood in the perpendicular direction. The shear failure was observed in all tested OSB panels, whereas shear failure, glue line delamination, and bending combined with shear failure were observed in the domestic plywood.

• Proceedings of the Mineralogical Society of Korea Conference
• /
• 2003.05a
• /
• pp.84-85
• /
• 2003

소백산육괴의 동부에 분포하는 영양-울진지역의 선캠브리아기 변성암류는 평해층, 기성층, 원남층, 평해화강편마암, 하다우백질화강편마암 등으로 구성되어 있다(김옥준 외, 1963). 그러나, 최근 김남훈 외(2001, 2002)은 야외조사연구와 암석학적 및 지구화학적 연구를 통하여 주로 변성화산암류로 기재되었던 기성층은 변성화산암류가 아니라 평해층과 원남층에서 산출되는 화강암질편마암과 각섬암 기원의 변성암류가 연성전단변형을 받아 형성된 압쇄암 내지 초압쇄암으로 되어 있고, 기존의 기성층은 변성화산암류와 같이 성분상으로 구분되는 별개의 층이 아닌 구조적으로 만들어진 연성전단대의 중심부일 가능성을 시사한 바가 있다. 본 연구는 연성전단대의 연장성 및 연성전단대 형성과 관련된 지구조운동의 특성을 파악하고, 중첩된 변형구조들의 선후관계로부터 영양-울진지역 선캠브리아기 변성암류에 대한 변형작용사를 규명하기 위해 기성층의 분포지를 중심으로 이 지역 선캠브리아기 변성암류에 대한 상세한 야외지질조사를 실시하였다. 그 결과, 예천(북후면-평은면)지역을 통과하여 봉화 부근에서 동북동-서남서 방향이 동-서 방향으로 전환하여 장군봉지역까지 연장되는 것으로 알려져 있는 우수 주향 이동성 예천전단대(KIGAM, 1995; 강지훈 외 1997; 강지훈, 2000; 강지훈과 김형식, 2000)는 영양-울진지역까지 연장됨이 확인된다. 또한, 영양-울진지역의 선캠브리아기 변성암류에는 연성전단변형 이전에 적어도 한 번의 습곡작용과 이후에 적어도 두 번의 습곡작용이 인지된다. 각 변형단계별 특징적인 구조요소를 요약하면 다음과 같다. D1 변형: 편마면 내지 편리(S0)가 습곡되어 형성된 F1 습곡은 동-서 방향의 준 수평적인 습곡축을 갖는 뿌리 없는 등사습곡 형태로 인지된다. 양 날개부의 S0 엽리는 F1 습곡축면(S1)으로 완전히 전위된 하나의 엽리(S0-1)로 나타나고, S0-1 엽리는 이 지역의 광역엽리로 인지된다. S0-1 광역엽리는 구성암류의 대상 분포 방향과 유사한 서북서 주향에 북쪽으로 중각 경사하는 집중된 방향성을 보이며 분산되어 나타난다. D2 변형: 변형구조로는 신장선구조, 압쇄구조면, 비대칭습곡 등으로 인지된다. 신장선구조는 S0-1 엽리면상에서 주로 신장된 석영(집합체)과 장석(집합체)들의 정향배열에 의해 정의되고, S0-1 엽리의 주향 방향으로 저각으로 침강하는 집중된 방향성을 보이며 분산되어 나타난다. 신장선구조에 평행하고 S0-1 엽리에 수직한 단면에서는 상부-동쪽-이동의 우수주향 이동성 연성 전단운동감각을 지시하는 구조요소들이 다량 관찰된다. 연성전단변형에 의해 형성된 압쇄구조면은 전단엽리와 압쇄엽리에 각각 해당하는 C면과 S면 등이 인지된다. 전단엽리 C면은 S0-1 광역엽리와 거의 일치하고, 압쇄엽리 S면은 F2 비대칭습곡의 축면엽리와 거의 일치한다. S0-1 엽리를 습곡시키는 F2 비대칭습곡은 S0-1 엽리를 전단면으로 하여 상부-동쪽-이동 전단운동에 의해 형성된 밀착습곡 형태로 인지된다. F2 습곡축은 북동 방향으로 중각 내지 저각 침강하고 F1 습곡축과는 65$^{\circ}$-75$^{\circ}$ 범위의 사이각을 이룬다. F2 습곡축면은 동북동 주향에 북쪽으로 중각으로 경사하고 F1 습곡축면과는 20$^{\circ}$-40$^{\circ}$ 범위의 사이각을 이룬다. D3 변형. S0-1 엽리와 압쇄구조면 등을 습곡시키는 F3 습곡은 준 수평적인 습곡축과 습곡축면을 갖는 개방 횡와습곡의 형태로 인지된다. D4 변형: F4 습곡은 비대칭 공역성 킹크습곡, 공역성 충상단층에 수반되어 나타나는 드래그습곡, 대칭 개방 직림습곡 등의 다양한 습곡 형태로 인지된다. 이들 F4 습곡의 축면엽리는 일반적으로 동-서 주향에 남쪽과 북쪽으로 경사한다. 그 경사각은 비대칭 공역성 킹크습곡(저각), 드래그습곡(중각), 대칭 개방 직립습곡(고각) 순으로 고각을 이룬다. F4 습곡축은 동쪽과 서쪽으로 저각 침강하는 집중된 방향성을 보인다. 공역성 충상단층은 동-서 주향에 남쪽과 북쪽으로 경사하는 단층면과 상부가 북쪽과 남쪽으로 충상하는 운동상을 보인다. 드래그습곡의 축면엽리는 이러한 공역성 충상단층운동의 전단압축방향에 수직으로 발달한다. 이러한 D4 변형구조는 남-북 방향의 압축 지구조 환경하에서 형성된 것으로 고찰된다.

• The korean journal of orthodontics
• /
• v.34 no.5 s.106
• /
• pp.429-438
• /
• 2004

The purpose of this study was to compare the effects of different light direction exposure times and setting times when using plasma arc light on shear bond strength of metal brackets. 240 extracted human premolars were randomly assigned to one of 16 groups Standardized brackets were bonded to enamel using different light curing units (Plasma arc light and Halogen light), exposure times (Plasma arc light 2. 4, 6 seconds and Halogen light 20 seconds). and light directions [Vertical direction [V] and Oblique direction [O]). 8 groups were tested after 5 minutes and the remaining 8 groups after 24 hours. The metal brackets were bonded with Transbond XT. Shear bond strength was measured by a universal testing machine. The results were as fellows: There were as differences between the shear bond strengths of the Vertical groups (V) and Oblique groups (O). regardless of exposure times and types of light curing units (p>0.05). The shear bond strength of the group with 2 seconds of plasma light were significantly lower than other exposure time groups (P<0.05). The shear bond strength tested after 5 minutes was lower than after 24 hours (p<0.05) The Adhesive Remment Index (ARI) score showed no statistically significant difference among the different groups. The results of this study suggested that the light direction of plasma arc light had no influence on the shear bond strength of metal brackets to enamel. and exposure times more than 4 seconds produced shear bond strengths similar to those Produced with a conventional halogen curing light.