• Industry Promotion Research
• /
• v.1 no.2
• /
• pp.1-6
• /
• 2016

By using the high tensile steel plate (SPFH590) 1 Primary normal shear process clearance was studied through an experiment for the effect of the second shaving process in this study. Experiment result, Shaving process in the case of processed 15% of the Primary normal shear process clearance was some residual surface does not remove it completely. and Shaving process of shearing products by the general shearing process clearance of 10% it was found that the wider the size of shear surface. The shear surface of 93% occurred in case of the clearance of general shearing process is 10% and the Shaving clearance is 2%, The shear surface of 87% were to occur in case of the Shaving clearance is 3%.

• Journal of the Korean Geotechnical Society
• /
• v.24 no.6
• /
• pp.69-75
• /
• 2008

Shear tests were carried out on interface between two concrete eco-blocks which comprise segmental retaining wall. Three interface conditions were considered : 1) direct contact of two blocks, 2) placing rubber pad between two blocks, 3) placing rubber pad and shear key between two blocks. According to shear tests, shear load-shear displacement relationship which was obtained from direct contact of two blocks was similar to elastic-perfectly plastic behavior. Ductile behavior of shear load-shear displacement relationship was observed for the interface condition of placing rubber pad. Apparent minimum shear capacities and apparent friction angles for the interface conditions of direct contact of two blocks, placing rubber pad between two blocks, placing rubber pad and shear key were 1.7 kN/m, $27.6^{\circ}$ and 4.2 kN/m, $26.2^{\circ}$ and 20.9 kN/m, $26.0^{\circ}$ respectively.

• Journal of the Korean GEO-environmental Society
• /
• v.17 no.2
• /
• pp.41-49
• /
• 2016

This paper evaluates the interface shear strength of HDPE textured geomembrane. The interface shear strength between textured geomembrane and marl, and textured geomembrane and woven geotextile were measured; and the smooth geomembrane was used to evaluate the effect of "texture" on the interface shear strength. The interface shear strength was measured using a large direct shear testing device under several conditions including the presence of water, and the normal stresses that were 12, 24, 45, 100, 500, and 1,000 kPa. From testing results, it was found that there was meaningful reduction in the interface shear strength in the presence of water, but the effect of normal stress was not clear. The interface shear strength was measured to be significantly different for smooth geomembrane, whose strength was measured to be as small as half that of the textured geomembrane.

• Tunnel and Underground Space
• /
• v.23 no.3
• /
• pp.203-211
• /
• 2013

Shear behavior of joint plane has been investigated considering the magnitude of normal stresses and initial surface roughness. Shear strength of joint plane has been measured by performing the multi-stage shear test in which applied normal stress level has been increased stepwise. Multi-stage shear test within the specified normal stress range has been repeated and two types of strength parameter variation have been observed: type 1 - both cohesion and friction angle decrease, type 2 - cohesion decrease and friction angle increase. Trends of strength parameter variation for the three rock types, gneiss, granite and shale, have been investigated and the influence of initial roughness of joint plane on the sequential shear strength change for the repeated multi-stage shear tests also has been analyzed.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.8
• /
• pp.3650-3655
• /
• 2013

A state purpose to produce fine blanking die gets to be the maximum size of share surface the study considered that change a size of share area. the clearance affecting most greatly size of share surface fixing as 1% of material thickness and while change share speed, A distance change from share line to V-ring center, A change of V-ring angle. it designed. Each test specimen taken from the share surface size analysis of the V-ring distance of 2mm, the outer $45^{\circ}$ / inner$30^{\circ}$ if the, Shear speed was found that the area of the entire cross section is largest the 6.4m/min.

• The Journal of Engineering Geology
• /
• v.31 no.3
• /
• pp.357-366
• /
• 2021

Shear behavior dependent on the shape and roughness of rock joints can greatly influence the stability of the ground and rock structures. The efficient design of rock structures requires understanding of the shear behavior due to joints and accurate calculation of the shear strength. This work reports numerical shear tests using PFC2D on No. 1 (JCR-1), with smooth joints, and No. 7 (JRC-7) and No. 9 (JRC-9), with relatively rough joints, for the 10 shapes of standard joint profiles proposed by Barton and Choubey (1977). The aim was to investigate the shear behavior of rock joints with respect to their roughness. The results show the maximum shear stress to be about 3.2 to 5.0 times greater in the rougher JRC-7 and JRC-9 joints than in smoother JRC-1. The maximum shear displacement was approximately 4.1 to 5.8 times greater at the first normal stress than at the second. The rougher joints showed friction angles of the rock joints that were approximately 1.8 to 3.9 times greater than that in the smooth joint. Overall, increasing the rock joint roughness increased the maximum shear stress and friction angle.

• Tunnel and Underground Space
• /
• v.13 no.3
• /
• pp.169-179
• /
• 2003

Anisotropic shear strength of rock joints is studied based on the artificially fractured specimens using experimental and analytical methods. Series of direct shear tests are performed to obtain the strength, stiffness and friction angle of joints under various low normal stresses and shearing directions. The results of shear strength and stiffness show anisotropic value according to shearing direction under low normal stress specially less than 2.45 MPa. But, the effect of joint roughness on strength decreases with increasing normal stress. To estimate more effectively the peak shear strength under low normal stress, the modified Barton's equation is suggested.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.31 no.6
• /
• pp.315-329
• /
• 2018

Recently, RC transfer slab systems have been used widely to construct high-rise wall-type apartments for securing parking space or public space. However, it is problem that the design method and structural performance evaluation method developed for thin RC flat slab are still used in the design of the transfer slab whose thickness is very thick and therefore structural behavior is expected to be different from RC flat slab. Thus, for the rational design of the transfer slab, the ultimate shear behavior of the RC transfer slab system is required to be analyzed properly. Accordingly, in the present study, the two-way shear behavior of the transfer slab was analyzed using nonlinear FEM according to various design parameters such as thickness of the transfer slab, strength of concrete, shear span ratio, and reinforcement ratio. In addition, the two-way shear strength evaluations of RC transfer slab by the existing evaluation methods were verified by comparing those with the results of nonlinear FEM analysis.

• Journal of the Korean GEO-environmental Society
• /
• v.7 no.3
• /
• pp.31-41
• /
• 2006

The scale effect of specimens on the shear behavior of joints is studied by performing direct shear tests on six different sizes in Granite. The peak and residual shear stress, shear displacement, shear stiffness, and dilation angle are measured with the different normal stress(0.29~2.65MPa) and roughness parameters. It is also shown that both the joint roughness coefficient(JRC) and the joint compression strength(JCS) reduce with increasing joint length. A series of shear tests show about 56~67% reduction in peak shear stress, and about 18~44% in residual shear stress, respectively as the contact area of joint increases from 12.25 to $361cm^2$. Also the variation of dilation angle is $27^{\circ}$ at normal stress of 0.29 MPa and $6^{\circ}$ at normal stress of 2.65 MPa, respectively. The envelopes considering scale effect for JRC are made for the peak shear strength of rock joint in comparison with the Barton's equation.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2002.10a
• /
• pp.213-227
• /
• 2002

절토사면의 붕괴원인은 토질 및 지질조건, 지형, 강우, 지하수 및 지표수, 사면형상, 굴착 및 발파와 같은 인위적인 조건, 사면보호공 등과 같이 다양한 영향이 있을 수 있으나 가장 많은 영향을 주는 원인으로 토질 및 지질적인 조건이라고 할 수 있다. 본 논문은 이러한 지질조건에서 붕괴가 발생될 경우의 활동면에 대한 전단강도 추정하는 방법에 있어 역해석법에 의한 활동면의 전단강도 추정을 연구하였다 연구결과 붕괴된 사면에서 화성암은 마찰각 20$^{\circ}$~30$^{\circ}$, 점착력 0~2t/$m^2$의 범위를 가지며 퇴적암에서는 마찰각 $10^{\circ}$~17$^{\circ}$, 점착력 0~2.5t/$m^2$의 범위, 변성암에서는 마찰각 $10^{\circ}$~40$^{\circ}$, 점착력 0~4.0t/$m^2$의 범위가 우세한 것으로 나타났다. 그리고 지질구별 구분에 의하면, 절리에 의해 붕괴가 발생된 경우에는 마찰각 30$^{\circ}$~40$^{\circ}$, 점착력 0~3.5t/$m^2$, 엽리면은 마찰각 30$^{\circ}$~35$^{\circ}$, 점착력 0.5~3.0t/$m^2$, 단층면은 마찰각 11$^{\circ}$~38$^{\circ}$, 점착력 0~3.0t/$m^2$, 층리면은 마찰각 $10^{\circ}$~17$^{\circ}$, 점착력 0~2.5t/$m^2$ 정도의 범위를 갖는 것으로 나타났다.