• Journal of applied mathematics & informatics
• /
• v.28 no.1_2
• /
• pp.217-231
• /
• 2010

We consider a class of elliptic problems of a logistic type $$-div(|{\nabla}_u|^{m-2}{\nabla}_u)\;=\;w(x)u^q\;-\;(a(x))^{\frac{m}{2}}\;f(u)$$ in a bounded domain of $\mathbf{R}^N$ with boundary $\partial\Omega$ of class $C^2$, $u|_{\partial\Omega}\;=\;+{\infty}$, $\omega\;\in\;L^{\infty}(\Omega)$, 0 < q < 1 and $a\;{\in}\;C^{\alpha}(\bar{\Omega})$, $\mathbf{R}^+$ is non-negative for some $\alpha\;\in$ (0,1), where $\mathbf{R}^+\;=\;[0,\;\infty)$. Under suitable growth assumptions on a, b and f, we show the exact blow-up rate and uniqueness of the large solutions. Our proof is based on the method of sub-supersolution.

• Korean Journal of Agricultural Science
• /
• v.47 no.2
• /
• pp.327-335
• /
• 2020

The purpose of this study was to analyze the load distribution and contact safety factor for the power take off (PTO) gear of a 71 kW class agricultural tractor. In this study, a simulation model of the PTO gear-train was developed using Romax DESGINER. The face load factor and contact safety factor were calculated using ISO 6336:2006. The simulation time was set at 2,736 hours considering the lifetime of the tractor, and the simulation was performed for each PTO gear stage at the engine rated power conditions. As a result of the simulation, the face load factors for the driving gear at the PTO 1^st, 2^nd and 3^rd stages were 1.644, 1.632, and 1.341, respectively. The contact safety factors for the driving gear at the PTO 1^st, 2^nd and 3^rd stages were 1.185, 1.216, and 1.458, respectively. As the PTO gear stage was increased, the face load factor decreased, and the contact safety factor increased. The load distributions for all the PTO gears were concentrated to the right of the tooth width. This causes stress concentrations and shortens the lifespan of the gears. Therefore, it is necessary to improve the face load factor and the contact safety factor with macro-geometry and micro-geometry.

• Journal of Environmental Impact Assessment
• /
• v.22 no.5
• /
• pp.491-511
• /
• 2013

In this study, three survey areas in Changnyeong, Miryang and Jinju of the confirmed the habitation of nutria and carried out the performance on the plant diet resource. From the habitat trace survey in the nutria habitat, a total of 336 trace points was shown. There were 181 trace points (54%) confirmed from St. 1 as the highest showing, followed by 52 trace points (15.4%) from St. 2, and 103 trace points (30.6)% from St. 3. The vascular plants distributed in the habitat area were a total of 182 taxonomic group with 57 families, 99 genus, 16 hybrids, and 1 race. The vascular plant living types in the habitat area are 1-year plant (Th, Th(w)) for 63class groups (34.6%), hemicryptophyte (H) for 42class groups(23.1%). plants, trees, crop plants were included. As a result of analyzing the overseas research cases on the diet plants of nutria, there are 195 taxonomic groups in a total of 39 families, 126 genus, 183 breeds, and 12 hybrids. In the study areas, feeding the plants was confirmed by the 7 taxonomic groups, aquatic plant, terrestrial From the total of 182 taxonomic groups discovered in the habitat area, 20 class groups, in 3 habitation region, 10 class groups of commonly appearing 49 class groups were shown to be the breed confirmed for diet in existing case studies, and assuming from it basis, the nutria habitating in the survey area is considered to have the supply of diverse diet resource to have flawless habitation. This is implication of having potential breeding possibility.

• Proceedings of the KIPE Conference
• /
• 2013.11a
• /
• pp.184-185
• /
• 2013

본 논문은 1.8MW 급 ESS용 배터리 충방전기 개발에 관한 논문이다. 제안된 회로의 구성은 삼상 교류 입력을 받아 DC 1150V로 변환시키는 3상 AC/DC 컨버터부와 배터리를 충전과 방전시키는 buck-boost 컨버터부로 구성된다. 출력은 최대 900V, 2000A 이며 C/C, C/V, C/P 모드로 제어된다. 3상 AC/DC 컨버터는 역률을 개선하고, 입력 고조파를 저감시킬 수 있으며, 계통으로 회생이 가능하다는 장점이 있다. 시뮬레이션 및 실험을 통하여 배터리 충방전기의 성능을 검증하였으며, 실제 시스템에 적용하여 충전 및 방전 시험을 완료하였다.

• Asian Pacific Journal of Cancer Prevention
• /
• v.14 no.7
• /
• pp.4167-4175
• /
• 2013

A najor current challenge and constraint in cervical cancer research is the development of vaccines against human papilloma virus (HPV) epitopes. Although many studies are done on epitope identification on HPVs, no computational work has been carried out for high risk forms which are considered to cause cervical cancer. Of all the high risk HPVs, HPV 16, HPV 18 and HPV 45 are responsible for 94% of cervical cancers in women worldwide. In this work, we computationally predicted the promiscuous epitopes among the E6 proteins of high risk HPVs. We identified the conserved residues, HLA class I, HLA class II and B-cell epitopes along with their corresponding secondary structure conformations. We used extremely precise bioinformatics tools like ClustalW2, MAPPP, NetMHC, Epi,Jen, EpiTop 1.0, ABCpred, BCpred and PSIPred for achieving this task. Our study identified specific regions 'FAFR(K)DL' followed by 'KLPD(Q)LCTEL' fragments which proved to be promiscuous epitopes present in both human leukocyte antigen (HLA) class I, class II molecules and B cells as well. These fragments also follow every suitable character to be considered as promiscuous epitopes with supporting evidences of previously reported experimental results. Thus, we conclude that these regions should be considered as the important for design of specific therapeutic vaccines for cervical cancer.

• Journal of Advanced Marine Engineering and Technology
• /
• v.38 no.6
• /
• pp.602-608
• /
• 2014

Hydrogen energy, a field of low-carbon substitute energy, can be produced by fossile fuel reforming and electrolysis of water etc. We developed 1kW class flat type reformer for PEM Fuel Cells. The PEMFC is highly sensitive to carbon monoxide because CO has detrimental effects on the performance of the fuel cell. Thus, reformed gas supplied to Fuel cell system, which maintained CO concentration below 10ppm. After applying optimum drive condition, reformed gas was measured with gas chromatography and could find out about each experimental condition of $H_2$ and CO concentration. As a results, The 1kW class plate type hydrogen generation system's optimum condition is A/F ratio ${\alpha}=1.3$, STR temperature 1023K, S/C ratio 3, and $PrOx1{\cdot}2$ 30cc/min. It turns out that installation of PrOx 2 stage is more efficient for reducing CO concentration.

• Proceedings of the SAREK Conference
• /
• 2009.06a
• /
• pp.167-171
• /
• 2009

We conducted performance test of a 350 kW class wood pellet boiler installed at a dormitory whose total area is $1,354\;m^2$. The maximum heating capacity of the boiler is 350 kW(300,000 kcal/kg). The wood pellet boiler consists of 3 parts; boiler, hot water storage tank and wood pellet storage tank. In testing the boiler, we shut off hot water utility supply and open up floor heating water system in order to measure exact value of the heating output of the wood pellet boiler. To determine the efficiency and heating output of the wood pellet boiler, we measured mass flow rate of wood pellet, the lower heating value(LHV) of the wood pellet, mass flow rate and temperature of water for floor heating and so on. We measured the mass flow rate of fuel, wood pellet with respect to rotational speed of auger, wood pellet feeding screw. We also measured the flue gas concentration of the wood pellet boiler by using a gas analyser. The result shows that the efficiency of the wood pellet boiler is 80.6% based on lower heating value at 124 kW of heating output. At this condition, O2 concentration of the flue gas is 6.0%, CO and NOx concentrations are 85 and 102 ppm.

• Korean Journal of Environment and Ecology
• /
• v.20 no.4
• /
• pp.415-424
• /
• 2006

This study was carried out to analyze the characteristics of forest watershed factors by using the quantification theory(I) for evaluation and prediction of the failure hazard area. Present $sediment(m^3/yr/ha)$ of erosion control dams were investigated in 95 sites of erosion control dam constructed during 1986 to 1999 in Gyeongnam province. The results obtained from this study were summarized as follows; General condition of class I(Very hazard area) were as follow; Igneous rock in parent rock, coniferous in forest type, below 20year in stand age, below 30cm in soil depth, SCL in soil texture, $31{\sim}40%$ in gravel contents, $S{\sim}E$ in aspect, $2,501{\sim}3,600m$ in length of main stream, $26{\sim}30$ in number of total streams, $6,601{\sim}10,000m$ in length of total streams, over 3 in stream order, over 16 in number of first streams order and over $31^{\circ}$ of slope gradient. General condition of class IIl(hazard area) were as follow; Metamorphic rock in parent rock, hardwood in forest type, over $21{\sim}24year$ in stand age, $31{\sim}40cm$ in soil depth, SiCL or SCL in soil texture, $11{\sim}20%$ in gravel contents, $S{\sim}W$ in aspect, $1,501{\sim}2,600m$ in length of main stream, $6{\sim}10$ in number of total streams, $3,501{\sim}5,500m$ in length of total streams, 2 in stream order, $6{\sim}10$ in number of first streams order and over $31^{\circ}$ of slope gradient. General condition of class III(Un hazard area) were as follow; Sedimentary rock in parent rock, mixed in forest type, over 25year in stand age, $41{\sim}50cm$ in soil depth, SiCL in soil texture, below 10% in gravel contents, $N{\sim}W$ in aspect, below 500m in length of main stream, below 5 in number of total streams, below 1,000m in length of total treams, below 1 in stream order, below 2 in number of first streams order and below $25^{\circ}$ of slope gradient. The prediction method of suitable for failure hazard area divided into class I, II, and III for the convenience of use. The score of class I evaluated as a very hazard area was over 4.8052. A score of class II was 4.8051 to 2.5602, it was evaluated as a hazard area, and class III was below 2.5601, it was evaluated as a un hazard area.

• Journal of Korean Society of Forest Science
• /
• v.105 no.4
• /
• pp.463-471
• /
• 2016

The purpose of this study was to develop allometric equations for identifying the amount of wood and building biomass statistics of L. tulipifera by density, biomass expansion factors and root ratio. For this purpose, total of 40 trees were sampled, which were used consideration the area and the DBH class. As a results, the wood density was $0.43g{\cdot}cm^{-3}$, biomass expansion factors were 1.2, root ratio was 0.2 and uncertainty were 3.9%, 4.6%, 24.1%, respectively. Allometric equations for above ground of L. tulipifera trees were $W=0.060D^{2.524}$. Total and underground allometric equations were $W=0.063D^{2.578}$, $W=0.010D^{2.591}$, respectively.

• Journal of the Semiconductor & Display Technology
• /
• v.18 no.4
• /
• pp.18-24
• /
• 2019

In this paper, expandable bobbin type multiple integrated coupled-inductor applied 4-paralled switching rectifier was proposed. To design the proposed inductor easily, inductance designing formula was derived through magnetic circuit analysis of the 4-paralleled integrated coupled-inductor. Furthermore, to verify practicality of the proposed inductor, it was applied in 600W class 4-paralleled interleaved switching rectifier, and the steady-state characteristics of the proposed inductor and discrete inductors were compared. Consequently, it was showed that the proposed inductor can replace the conventional discrete inductors with alternative electrical characteristic standard, hence miniaturization of the SMPS can be achieved. From the test result, test circuit with the proposed inductor showed maximum 97.1% of power conversion efficiency and under 18W of power loss where the circuit with discrete inductors showed 96.7% and 20W respectively.