• 한국재료학회지
• /
• 제25권12호
• /
• pp.703-707
• /
• 2015

In this study, we investigated the effect of annealing conditions on the ferromagnetic resonance(FMR) of yttrium iron garnet ($Y_3Fe_5O_{12}$, YIG) thin film prepared on gadolinium gallium garnet ($Gd_3Ga_5O_{12}$, GGG) substrate. The YIG thin films were grown by rf magnetron sputtering at room temperature and were annealed at various temperatures from 700 to $1000^{\circ}C$. FMR characteristics of the YIG thin films were investigated with a coplanar waveguide FMR measurement system in a frequency range from 5 to 20 GHz. X-ray diffraction(XRD) and X-ray photoelectron spectroscopy(XPS) were used to characterize the phase formation, crystal structure and composition of the YIG thin films. Field dependent magnetization curves at room temperature were obtained by using a vibrating sample magnetometer(VSM). The FMR measurements revealed that the resonance magnetic field was highly dependent on the annealing condition: the lowest FMR linewidth can be observed for the $800^{\circ}C$ annealed sample, which agrees with the VSM results. We also found that the Fe and O composition changes during the annealing process play important roles in the observed magnetic properties.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2002년도 하계학술대회 논문집 C
• /
• pp.1485-1487
• /
• 2002

The 0.96Mg$TiO_3$-0.04Sr$TiO_3$ ceramics with $V_2O_5$(5wt%) were prepared by the conventional mixed oxide method. The structural properties were investigated with sintering temperature by XRD and SEM. According to the X-ray diffraction patterns of the 0.96Mg$TiO_3$-0.04Sr$TiO_3$ceramics with $V_2O_5$(5wt%), the ilmenite $MgTiO_3$ and perovskite $SrTiO_3$ structures were coexisted and secondary phase $MgTi_2O_5$ were appeared. Increasing the sintering temperature, the grain size was increased and three types of grains were exhibited: larger circular grain, small square grain and lapth-shaped grain. In the case of 0.96Mg$TiO_3$-0.04Sr$TiO_3$ ceramics with $V_2O_5$(10wt%), dielectric constant, quality factor and temperature coefficient of resonant frequency were $15.24{\sim}18.55$, $22,890{\sim}42,100$GHz, -24.5${\sim}$+2.414ppm/$^{\circ}C$, respectively.

• 한국전기전자재료학회논문지
• /
• 제14권3호
• /
• pp.190-196
• /
• 2001

The microwave dielectric properties and a sintering behavior of MgTiO$_3$-CaTiO$_3$ ceramics doped with Li were investigated. The main composition was fixed as 0.94MMgTiO$_3$-0.06CaTiO$_3$ and Li$_2$CO$_3$was added excessively in the range of 0~10 mol% (with reference to Li atoms) and the specimens were sintered at 1200~140$0^{\circ}C$ for 4 hours. When the amount of Li was small the quality factor and dielectric constant were reduced, while those tow properties increased if the Li amount was above 1 mol%. But if Li was overly added those dielectric properties decreased again. Li, if added in the composition range of 1.0~3.0 mol%, can increase the quality factor of MgTiO$_3$-CaTiO$_3$ ceramics. The optimum amount of Li was 1.5mol% and sinterign condition was 1275$^{\circ}C$/4hr, at which we cudl obtain following results ; dielectric constant ($\varepsilon$$_{r}$) of f20.0, quality factor(Qxf$_{0}$) of 78,000 GHz and temperature coefficient of resonant frequency($\tau$$_{f}$) of -1.6 ppm/$^{\circ}C$.>.>.>.

• 한국세라믹학회지
• /
• 제41권1호
• /
• pp.9-12
• /
• 2004

The effect of x wt% CuO-y wt% $V_2O_5$ content on the microwave properties of $(Pb_{0.45}Ca_{0.55})[(Fe_{0.5}Nb_{0.5})_{0.9}Sn_{0.1}]O_3$ (PCFNS) ceramics was investigated. In order to decrease the sintering temperature and use as a Low Temperature co-firing Ceramics (LTCC), CuO-$V_2O_5$ are added in the PCFNS. The bulk density, dielectric constant (${\varepsilon}_r$) and quality factor(Q${\cdot}f_0$) increased with increase in CuO content within a limited value. The microwave properties were degraded with increases in $V_2O_5$ content. The temperature coefficient of the resonant frequency (${\tau}_f$) of PCFNS was shifted to positive value abruptly with increasing the $V_2O_5$ content, while the ${\tau}_f$ was slightly shifted to positive value with increasing the CuO content. The optimized microwave properties, ${\varepsilon}_r$ = 88, Q${\cdot}f_0$ = 6100 (GHz), and ${\tau}_f$ = 18 ppm/$^{\circ}C$, were obtained in $(Pb_{0.45}Ca_{0.55})[(Fe_{0.5}Nb_{0.5})_{0.9}Sn_{0.1}]O_3$ with 0.2wt% CuO 0.05 wt% $V_2O_5$ and sintered at $1000^{\circ}C$ for 3 h. The relationship between the microstructure and microwave dielectric properties of ceramics was studied by X-Ray Diffraction (XRD) and Scanning Electron Microscopy (SEM)

• 한국전자파학회논문지
• /
• 제18권2호
• /
• pp.206-212
• /
• 2007

본 논문에서는 넓은 영역에서 GBN/SSN 억제 특성을 보이는 이종 셀 EBG 구조를 이용한 새로운 전원면 구조를 제안하였다. 제안된 구조는 -30 dB 이하의 삽입 손실로 정의되는 저지 대역이 GBN의 에너지가 집중적으로 분포하는 수 백 MHz에서 시작하며 약 7.9 GHz의 넓은 대역폭을 갖는다. 본 구조의 특징은 인덕턴스를 강화하는 나선형 연결 선로와 분산적 LC 회로의 주기를 줄이는 이종 셀을 추가한 것이다. 그 결과 -30 dB 저지 대역의 저주파에서의 차단 주파수가 낮아짐은 물론 대역폭이 넓어진 특성을 보였다. 또한, 전원면과 접지면 사이의 구조적 공진 모드가 현격히 억제되었으며 평행판 도파관에 비해 낮은 EMI 특성을 보였다.

• 한국전자파학회논문지
• /
• 제18권12호
• /
• pp.1327-1336
• /
• 2007

본 논문에서는 PIN 다이오드를 사용하여 disk-loaded 다이폴 안테나와 folded 다이폴 안테나로 형상이 변화하는 새로운 구조의 소형 안테나를 개발하였다. 개발된 안테나는 PIN 다이오드의 RF on/off 특성을 이용하여 안테나의 전기적 길이를 변화시켜 이중 대역에서 동작하며, 저주파 대역에서는 높은 복사 저항 값을 가지는 folded 다이폴 안테나로 동작하고 고주파 대역에서는 수평 방향으로 무지향성의 복사 패턴과 수직 방향으로 도넛 형태의 복사 패턴을 가지는 disk-loaded 다이폴 안테나로 동작한다. 제안된 안테나는 $20{\sim}300$ MHz에서 30cm 다이폴 안테나에 비해 크기가 소형화 되었음에도 높은 이득을 가진다. 또한, $300{\sim}1,300$ MHz에서 $80^{\circ}$ 이상의 넓은 빔 폭을 가짐으로써 방향 탐지 안테나로 사용이 가능하다.

• 한국전자파학회논문지
• /
• 제27권1호
• /
• pp.88-91
• /
• 2016

본 논문에서는 WPAN(Wireless Personal Area Network) 주파수 간섭원에 의한 MIMO(Multi Input Multi Output)-OFDM(Orthogonal Frequency Division Multiplexing) WLAN(Wireless Local Area Network)의 성능 열화를 분석하기 위해 LabVIEW와 USRP (Universal Software Radio Peripheral)를 이용한 실시간 주파수 간섭 분석 시스템을 제안하였다. 제안한 시스템은 간섭원과 피간섭원을 각각 소프트웨어로 구현하고, USRP와 연결하여 실제 시스템과 유사한 2.4 GHz 대역의 송신신호를 발생시킨 후, 피간섭원의 수신과정에 잡음신호 및 간섭신호와 결합하여, 주파수 공동사용에 따른 MIMO 시스템의 BER(Bit Error Rate)을 분석하는 방식이다. 분석 결과, 이론값과 거의 일치하는 결과를 보여 제안한 시스템의 타당성을 입증하였다.

• 한국전자파학회논문지
• /
• 제22권4호
• /
• pp.470-480
• /
• 2011

기존의 수동 위상 배열 시스템에 사용되는 구형 도파관(rectangular waveguide)을 이용한 아날로그 페라이트 위상 천위기는 높은 전력 취급 능력을 갖는 반면에 무겁고 높은 제작 비용을 갖는다. 본 논문에서는 PCB 제작 공정을 이용하여 낮은 제작 비용으로 쉽게 제작이 가능한 기판 집적 도파관(SIW)을 이용한 아날로그 페라이트 위상 천위기를 제안한다. 본 제안 구조는 페라이트를 삽입할 부분의 유전체를 제거하고, 그 부분에 페라이트를 삽입하여 제작하였다. 측정 결과, 중심 주파수 14.05 GHz에서 최대 $5.1^{\circ}$/mm 위상 변화를 관찰하였으며, 12.9 dB 이하의 반사 손실의 변화를 관찰하였다. 본 제안 위상 천이기는 위상 배열 시스템의 경량화 및 저가격화에 중요한 역할을 할 수 있을 것으로 기대한다.

• Journal of Electrical Engineering and Technology
• /
• 제1권4호
• /
• pp.435-447
• /
• 2006

This paper presents an application of the parallel Adaptive Evolutionary Algorithm (AEA) to search an optimal solution of the service restoration in electric power distribution systems, which is a discrete optimization problem. The main objective of service restoration is, when a fault or overload occurs, to restore as much load as possible by transferring the de-energized load in the out of service area via network reconfiguration to the appropriate adjacent feeders at minimum operational cost without violating operating constraints. This problem has many constraints and it is very difficult to find the optimal solution because of its numerous local minima. In this investigation, a parallel AEA was developed for the service restoration of the distribution systems. In parallel AEA, a genetic algorithm (GA) and an evolution strategy (ES) in an adaptive manner are used in order to combine the merits of two different evolutionary algorithms: the global search capability of the GA and the local search capability of the ES. In the reproduction procedure, proportions of the population by GA and ES are adaptively modulated according to the fitness. After AEA operations, the best solutions of AEA processors are transferred to the neighboring processors. For parallel computing, a PC cluster system consisting of 8 PCs was developed. Each PC employs the 2 GHz Pentium IV CPU and is connected with others through switch based fast Ethernet. To show the validity of the proposed method, the developed algorithm has been tested with a practical distribution system in Korea. From the simulation results, the proposed method found the optimal service restoration strategy. The obtained results were the same as that of the explicit exhaustive search method. Also, it is found that the proposed algorithm is efficient and robust for service restoration of distribution systems in terms of solution quality, speedup, efficiency, and computation time.

• 한국전기전자재료학회논문지
• /
• 제16권12S호
• /
• pp.1205-1209
• /
• 2003

We investigated the effects of calcination temperatures on the sintering behaviors and microwave dielectric Properties of (Z $n_{0.8}$M $g_{0.2}$)Ti $O_3$ system. Highly densified samples were obtained at the sintering temperatures below 100$0^{\circ}C$ with additions of 0.45 wt.%B $i_2$ $O_3$ and 0.55 wt.% $V_2$ $O_{5}$. From the examination of the existing phases and microstructures before and after sintering of (Z $n_{0.8}$M $g_{0.2}$)Ti $O_3$ system which is calcined at the various temperatures ranging from 80$0^{\circ}C$ to 100$0^{\circ}C$, it was found that higher Q${\times}$ $f_{o}$ values were obtained when unreacted phases in calcined body were reduced. When calcined at 100$0^{\circ}C$ and sintered at 90$0^{\circ}C$, it consists of hexagonal as. a main phase with uniform microstructure and exhibits Q${\times}$ $f_{o}$ value of 42,000 GHz and dielectric constant of 22. 22. 22.