• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.8
• /
• pp.888-899
• /
• 2012

In this paper, we present refarming plans and discuss about Radio Waves Law improvements to promote the efficient use of the 1.8 GHz(3GPP band 3) which is emerging as the best prime band for LTE-FDD service. We think it is important to make use of the entire band for mobile use in accordance with contiguity requirement, especially for LTE such as European countries, which is currently separated between different uses. We present two options with illustrative examples to enable that objective. And we identify several provisions in the Radio Waves Law expected to cause controversy when activates one between two options as the policy, and discuss improvements of those.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.29 no.10
• /
• pp.745-751
• /
• 2018

This paper reports on the design of a multiband multiple-input and multiple-output(MIMO) antenna for long-term evolution(LTE) vehicular communication and includes an analysis of the throughput field test results that were acquired by mounting the antenna to a vehicle. The antenna used for the field test was designed as a planar structure and included multiple stubs to obtain multiband resonant characteristics operating in the LTE(0.8~0.9 GHz, 1.7~2.2 GHz), Wi-Fi(2.4~2.48 GHz), and wireless access in vehicular environments (WAVE)(5.8~5.9 GHz) frequency bands. For the field test, antenna prototypes were mounted on the dashboard and roof of a vehicle and connected to the experimental LTE modem. The data transfer rate(throughput), signal-to-interference-plus-noise ratio(SINR), and reference signal received quality(RSRQ) were measured and analyzed in various real-world radio wave environments. Based on these results, the relationship between the SINR and throughput according to the field intensity is confirmed.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.40 no.8
• /
• pp.549-554
• /
• 2003

In this paper, we have designed and implemented by a monolithic microwave integrated circuit(MMIC) of a 5.8GHz-band low noise amplifier (LNA) composed of receiver front-end(RFE) in a on-board equipment system for dedicated short range communication. The designed LNA is provided with two active devices, matching circuits, and two drain bias circuits. Operating at a single supply of 3V and a consumption current of 18mA, The gain at center frequency 5.8GHz is 13.4dB, NF is 1.94dB, Input IP3 is -3dBm, S$_{11}$ is -18dB, and S$_{22}$ is -13.3dB. The circuit size is 1.2 $\times$ 0.7 $\textrm{mm}^2$.>.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.51 no.6
• /
• pp.282-289
• /
• 2014

In this paper, the UWB (Ultra Wide Band) band-pass filter (BPF) with compact-size using impedance mismatching in transmission line and SIR (Stepped Impedance Resonator) instead of open stubs is presented. The proposed BPF have 103 % of bandwidth and 11.2 GHz of center frequency, respectively. In additional, the operation frequencies of the suggested BPF are 4.8 GHz to 16 GHz. In this structure, the length of the transmission line is reduced to half compared with the original one by impedance mismatching technique with low frequency band (sub harmonics) and harmonic components. Also, the open stub can be used for SIR due to reduced size. Experimental results show that the insertion and return losses are 0.35 dB and 15.1 dB, respectively and the filter size is $8.92{\times}10.6mm^2$. The proposed BPF is in good agreement.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.24 no.8
• /
• pp.820-830
• /
• 2013

As wireless traffic drastically increase with the expansion of smart equipment, it is necessary to develop spectrum sharing technologies and introduce spectrum sharing policy for utilizing limited radio resources efficiently. In order to meet these new changes, this parper investigated the government-held (or license) spectrum to seek candidate frequency bands of spectrum sharing. Based on the database of the existing radio station, the investigated candidate frequency bands of spectrum sharing was experimented locally, considering the central frequency, bandwidths, and the region where the radio station is usedIn conclusion, we found out about 901 MHz bandwidths for regional spectrum sharing within the spectrum of 1~4.5 GHz. These bandwidths can be utilized in M2M and WiFi services, etc. based on spectrum sharing technology in the future.

• Journal of Advanced Navigation Technology
• /
• v.19 no.6
• /
• pp.623-629
• /
• 2015

In the present study, a coplanar waveguide (CPW)-fed printed monopole antenna with an inverted n-shaped slot is newly proposed for dual band operations which cover bandwidths of CDMA (1.85~2.025 GHz) and WLAN (2.4~2.484 GHz) as well as implementation of omnidirectional radiation pattern. For enhancement of impedance bandwidth ($S11{\leq}10dB$) in 2.4 GHz WLAN frequency band, an inverted n-shaped slot instead of the previous n-shaped slot is etched on the printed radiating monopole. The proposed antenna is designed and fabricated on one side of FR4 substrate with dielectric constant of 4.4, thickness of 1.6 mm, and size of $50{\times}25mm^2$. It has been observed that the measured impedance bandwidths are 280 MHz (1.84~2.12 GHz) in frequency band of CDMA and 420 MHz (2.38~2.8 GHz) in WLAN frequency band respectively. It is noticeable that impedance bandwidth in 2.4 GHz frequency band of WLAN is enlarged to three times due to use of inverted L-shaped slot in comparison with impedance bandwidth 140 MHz (2.39~2.53 GHz) obtained by use of the previous n-shaped slot. In addition, good omnidirectional radiation patterns have been observed over the entire frequency band of interest.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.14 no.3
• /
• pp.475-482
• /
• 2019

In this paper, we propose a triple band antenna for GPS / DCS / WLAN system. The proposed antenna has the characteristics required by considering the interconnection of two strip lines and various slits on the ground place. The total substrate size is $31mm(W1){\times}50mm(L1)$, thickness (h) 1.6 mm, and the dielectric constant is 4.4, which is made of $22mm(W7+W12+W8){\times}43mm(L4+L3)$ antenna size on the FR-4 substrate. From the fabrication and measurement results, bandwidths of 340 MHz (1.465 to 1.805 GHz), 480 MHz (2.155 to 2.635 GHz) and 1950 MHz (4.975 to 6.925 GHz) were obtained on the basis of -10 dB. Also, gain and radiation pattern characteristics are measured and shown in the frequency triple band as required.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.12
• /
• pp.1264-1271
• /
• 2009

In this paper, the chip slot antenna which is used for mobile devices and designed for multi-band is proposed. The proposed antenna is comprised of a chip antenna(10 mm$\times$20 mm$\times$1.27 mm) and a system circuit board(30 mm$\times$60 mm$\times$0.8 mm). The chip slot antenna is mounted on the system circuit board and the end of F-type strip line which is patterned on the chip antenna is connected by a via with a ground plane of the system circuit board. So, a chip antenna radiates effectively the energy by transition between a microstrip line of the system circuit board and a open slot structure of the chip antenna. In the results of proposed antenna, impedance bandwidth of 3:1 VSWR(-6 dB return loss) is 1.98 GHz(1.61~3.59 GHz) and 0.8 GHz(5.2~6 GHz). So, it can cover multi-band of DCS, PCS, UMTS, WLAN. The proposed antenna can be applied to mobile devices.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.25 no.10
• /
• pp.1040-1049
• /
• 2014

In this paper, a quad-band antenna for DCS1800, PCS1900, WCDMA, WLAN and Mobile WiMAX application is proposed. The proposed antenna is a printed monopole structure, and consists of two rectangular ring-shaped radiating patches on the front side and two different size of L-shaped slots on the back side(ground plane). Two rectangular ring radiation patches are respectively resonant at 2 GHz and 3.5 GHz bands, and additional resonance is occurred at 5.3 GHz by the coupling effect between two ring patches. In addition, the optimized matching characteristic is obtained by controlling the gaps. Also, by adding two L-slots on the ground plane, additional resonant frequency band of 5.6 GHz is occurred. Finally the measured bandwidths of the proposed antenna below -10 dB return loss are 1,200 MHz(1.6~2.8 GHz), 800 MHz(3.2~4.0 GHz), 300 MHz(5.14~5.44 GHz), and 690 MHz(5.56~6.25 GHz). The radiation patterns have the omni-directional characteristic, and the measured antenna average gains at resonant bands are 0.86~4.07 dBi.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.1 s.116
• /
• pp.37-43
• /
• 2007

In this.paper, we introduce design and implementation results of the single balanced diode mixer for European point-to-point microwave radio in order to improve flatness performance. When a resonator such as RF filter is integrated with a mixer, impedance characteristic of 50 ohm is maintained only in RF band, not in LO band resulting deterioration of flatness performance because of LO power variation on the diode. In the paper, we suggest a design method of mixer integrated with image rejection filter and LO harmonic filter to have a better performance of flatness using embedding electrical length between filter and mixer's port. Frequency specification of fabricated mixer is $21.2{\sim}22.6\;GHz$ for RF, $19.32{\sim}20.72\;GHz$ for LO and 1.88 GHz+/-50 MHz for IF, respectively. Measured results show conversion loss of 8.5 dB, flatness of 2 dB, input PldB of 8 dBm, IIP3 of 15 dBm under LO power level of 10 dBm. Return losses of RF, LO and IF port are under -12 dB, -10 dB and -5 dB, respectively. Isolations of LO/RF and LO/IF are 20 dB and 50 dB, respectively.