• The Transactions of the Korean Institute of Power Electronics
• /
• v.11 no.4
• /
• pp.328-339
• /
• 2006

In this paper the characteristic analysis of a single-phase switched reluctance motor (SRM) drive system with power factor correction (PFC) circuit is presented. The SRM is a low cost, simple and has a good high speed performance. The SRM drive with diode rectifier and filter capacitor has a low power factor because of short switch on time of capacitor. A novel switching topologic is presented to improve power factor and reduce torque ripple based on analysis of PFC circuit. Accordingly the SRM drive system with PFC circuit is also presented. Through the numerical analysis of the system, the toque ripple, power factor and efficiency with the change of rotary speed, load torque and capacity of the capacitor are achieved and compared with actual measured value.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.19 no.1
• /
• pp.91-97
• /
• 2014

Recently, the LED(Light Emitting Diode) is expected to replace conventional lamps including incandescent, halogen and fluorescent lamps for some general illumination application, due to some obvious features such as high luminous efficiency, safety, long life, environment-friendly characteristics and so on. To drive the LED, a single stage PFC(Power Factor Correction) flyback converter has been adopted to satisfy the isolation, PFC and low cost. The conventional flyback LED driver has the serious disadvantage of high 120Hz output current ripple caused by the PFC operation. To overcome this drawback, a new PFC flyback with low 120Hz output current ripple is proposed in this paper. It is composed of 2 power stages, the DCM(Discontinuous Conduction Mode) flyback converter for PFC and BCM(Boundary Conduction Mode) boost converter for tightly regulated LED current. Since the link capacitor is located in the secondary side, its voltage stress is small. Moreover, since the driver is composed of 2 power stages, small output filter and link capacitor can be used. Especially, since the flyback is operated at DCM, the PFC can be automatically obtained and thus, an additional PFC IC is not necessary. Therefore, only one control IC for BCM boost converter is required. To confirm the validity of the proposed converter, theoretical analysis and experimental results from a prototype of 24W LED driver are presented.

• Geomechanics and Engineering
• /
• v.20 no.1
• /
• pp.55-66
• /
• 2020

The damage or failure of coal rock is accompanied by energy accumulation, dissipation and release. It is crucial to study the energy evolution characteristics of coal rock for rock mechanics and mining engineering applications. In this paper, coal specimens sourced from the Xinhe mine located in the Jining mining area of China were initially subjected to uniaxial compression, and the micro-parameters of the two-dimensional particle flow code (PFC^2D) model were calibrated according to the experimental test results. Then, the PFC^2D model was used to subject the specimens to substantial uniaxial compression, and the energy evolution laws of coal specimens with various schemes were presented. Finally, the elastic energy storage ratio m was investigated for coal rock, which described the energy conversion in coal specimens with various arrangements of preformed holes. The arrangement of the preformed holes significantly influenced the characteristics of the crack initiation stress and energy in the prepeak stage, whereas the characteristics of the cumulative crack number, failure pattern and elastic strain energy during the loading process were similar. Additionally, the arrangement of the preformed holes altered the proportion of elastic strain energy U_e in the total energy in the prepeak stage, and the probability of rock bursts can be qualitatively predicted.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.4 no.4
• /
• pp.377-383
• /
• 1999

A new soft switching single stage AC-DC full bridge boost converter with unit input power factor and isolated output i is presented in this paper. Due to the use of a non-dissipative snubber on the primary side, a single stage high-power f factor isolated full bridge boost converter has a significant reduction of switching losses in the main switching devices. The non-dissipative snubber adopted in this study consists of a snubber capacitor Cr, a snubber inductor Cr, a fast r recovery snubber diode Dr' and a commutation diode Dp. This paper presents the complete operating principles, t theoretical analysis and experimental results.

• Proceedings of the KIPE Conference
• /
• 1999.07a
• /
• pp.319-322
• /
• 1999

This paper presents a novel single-stage Power Factor Corrected(PFC) AC/DC forward converter with semi-automatic current shaping in order to achieve the unity power factor and an isolated output. Since the proposed circuit is combined a boost converter used for PFCs with a forward converter used for DC to DC conversion, the over-all size of system could be reduced. And thanks to the zero voltage switching(ZVS) in both switches, the voltage stress can be reduced considerably. A simple auxiliary circuit adopted into the secondary of transformer is composed of lossless components for reducing surge voltage. A prototype which has tow IGBT(Insulated Gate Bypolar Transistor) modules as switching device is manufactured to evaluate the proposed topology. The characteristics of the proposed circuit are tested, and the validity is verified by experimental results.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.22 no.1
• /
• pp.87-94
• /
• 2008

A method for improving current THD of Valley-fill rectifier is proposed in this paper. The proposed topology combines a boosting inductor with Valley-fill rectifier which carry out AC/DC conversion and PFC simultaneously The boosting effect by PWM switching makes low THD current and improve of Valley-fill rectifier. The operation modes and THD of input current are analyzed as applied the boosting inductor, and the optimum value of boosting inductor is determined A 100[W] single-stage converter has been designed and tested. Experimental results are resented to verify the validity of the proposed method.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.15 no.1
• /
• pp.35-42
• /
• 2010

This paper presents the Two-stage LED Driving system using LLC resonant converter for LED lighting application. Due to the existence of the nonisolation DC/DC converter to control the LED current and the light intensity, the conventional three-stage LED Driving system has the problem of low power conversion efficiency. To solve this problem, a novel scheme without any nonisolation DC/DC converter is proposed, in which, the isolated DC/DC converter, e.g., LLC resonant converter in the paper, can perform the LED current control and stage, e.g., PFC stage and LLC stage, the efficiency can be significantly improved. Moreover, the cost and the volume of the whole LED driving system can be reduced compared to those of the conventional ones. The operational principle and the characteristics of the proposed scheme are presented. The proposed scheme is verified experimentally with a 45W output prototype LED driver.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.23 no.1
• /
• pp.59-65
• /
• 2018

A new single-stage flyback power converter with PFC for electrolytic capacitor-less LED driver is proposed in this study. This method minimizes the peak-to-average ratio of the LED driving pulsating current by adding the LED driving current near the LED current valley area, as well as the third harmonic component injection into the input current. The reduced peak current value of the LED drive current minimizes the thermal stress of the LED itself, thereby increasing the reliability of the LED, as well as achieving a long lifetime. Simulation and experimental results show the usefulness of the proposed topology.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.12 no.6
• /
• pp.2707-2712
• /
• 2011

In this paper, a power factor correction (PFC) control circuit using single stage boundary conduction mode(BCM) for the 400V. 120W LED drive application has been designed. The proposed control circuit is aimed for improvement of the power factor correction and reduction of the total harmonic distortion. In this circuit, a new CMOS multiplier structure is used instead of a conventional BJT(bipolar junction transistor) based multiplier where has a relatively large area. The CMOS multiplier can bring 30 % reduced chip area, competitive die cost in comparison with the conventional BJT multiplier.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.14 no.2
• /
• pp.52-58
• /
• 2000

This paper presents a novel power factor corrected(PFC) single-stage AC/DC half-bridge converter, which features discontinuous conduction mode(DCM) and soft-switching. The reduced conduction losses are achieved by the employment of a novel powder factor correction circuitry, instead of the conventional configuration composed of a front-end rectifier followed by a boost converter. To identify the validity of the proposed converter, simulated results of 500[W] converter with 100[V] input voltage and 50[V]output voltage are presented.