• Progress in Superconductivity
• /
• v.7 no.1
• /
• pp.46-51
• /
• 2005

We have developed control electronics to operate flux-locked loop (FLL), and analog signal filters to process FLL outputs for 64-channel Double Relaxation Oscillation SQUID (DROS) magnetocardiography (MCG) system. Control electronics consisting of a preamplifier, an integrator, and a feedback, is compact and low-cost due to larger swing voltage and flux-to-voltage transfer coefficients of DROS than those of dc SQUIDs. Analog signal filter (ASF) serially chained with a high-pass filter having a cut-off frequency of 0.1 Hz, an amplifier having a gain of 100, a low-pass filter of 100 Hz, and a notch filter of 60 Hz makes FLL output suitable for MCG. The noise of a preamplifier in FLL control electronics is $7\;nV/{\surd}\;Hz$ at 1 Hz, $1.5\;nV/{\surd}\;Hz$ at 100 Hz that contributes $6\;fT/{\surd}\;Hz$ at 1 Hz, $1.3\;fT/{\surd}\;Hz$ at 100 Hz in readout electronics, and the noise of ASF electronics is $150\;{\mu}V/{\surd}\;Hz$ equivalent to $0.13\;fT/{\surd}\;Hz$ within the range of $1{\sim}100\;Hz$. When DROSs are connected to readout electronics inside a magnetically shielded room, the noise of 64-channel DROS system is $10\;fT/{\surd}\;Hz$ at 1 Hz, $5\;fT/{\surd}\;Hz$ at 100 Hz on the average, low enough to measure human MCG.

• ETRI Journal
• /
• v.25 no.3
• /
• pp.203-209
• /
• 2003

This paper reports on our investigation of DC and RF characteristics of p-channel metal oxide semiconductor field effect transistors (pMOSFETs) with a compressively strained $Si_{0.8}Ge_{0.2}$ channel. Because of enhanced hole mobility in the $Si_{0.8}Ge_{0.2}$ buried layer, the $Si_{0.8}Ge_{0.2}$ pMOSFET showed improved DC and RF characteristics. We demonstrate that the 1/f noise in the $Si_{0.8}Ge_{0.2}$ pMOSFET was much lower than that in the all-Si counterpart, regardless of gate-oxide degradation by electrical stress. These results suggest that the $Si_{0.8}Ge_{0.2}$ pMOSFET is suitable for RF applications that require high speed and low 1/f noise.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.11a
• /
• pp.898-902
• /
• 2006

The motion of a system composed of a plate, constant springs and varying dampers is considered when the system is subject to harmonic force. Letting the frequencies of harmonic force and damper variation ${\Large f}_1\;and\;{\Large f}_2$ respectively, the displacement at the center of the plate has the strongest component at frequency ${\Large f}_1$. The angular displacement of the plate has strong components at ${\Large f}_1-{\Large f}_2$ and the natural frequency of the rotational mode of the system. If these two frequencies coincide, the plate oscillates with almost single frequency and a large amplitude. Part of these simulation results are proved analytically.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.16 no.9 s.114
• /
• pp.958-963
• /
• 2006

The motion of a system composed of a plate, constant springs and varying dampers is considered when the system is subject to harmonic force. Letting the frequencies of harmonic force and damper variation $f_1\;and\;f_2$, respectively, the displacement at the center of the plate has the strongest component at frequency $f_1$. The angular displacement of the plate has strong components at $f_1-f_2$ and the natural frequency of the rotational mode of the system. If these two frequencies coincide, the plate oscillates with almost single frequency and a large amplitude. These results can be applied to development of a moment shaker with low frequencies.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.05a
• /
• pp.81-85
• /
• 2006

The motion of a system composed of a plate, constant springs and varying dampers is considered when the system is subject to harmonic force. Letting the frequencies of harmonic force and damper variation ${\Large f}_1\;and\;{\Large f}_2$, respectively, the displacement at the center of the plate has the strongest component at frequency ${\Large f}_1$. The angular displacement of the plate has strong components at ${\Large f}_1-{\Large f}_2$, and the natural frequency of the rotational mode of the system. If these two frequencies coincide, the plate oscillates with almost single frequency and a large amplitude. These results can be applied to development of a moment shatter with low frequencies.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.13 no.7
• /
• pp.679-686
• /
• 2002

Based on the alternating series expansion of error probability function due to phase noise in PSK systems, the performance evaluations for Tikhonov and Gaussian probability density functions were performed in this paper. The range of the signal-to-noise ratio of recovered carrier signal which provides the same dependency between the error performances by Tikhonov function and Gaussian function was analyzed via loss evaluation due to phase noise. The phase noise with 1/f$^2$ characteristic was generated based on the relationship of the phase noise spectral density and the modulation index for frequency modulation signal. Using the generated phase noise as the input signal for digital satellite communication receiver, the performance losses due to the phase noise were measured and evaluated with the analyzed performance characteristics.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.05a
• /
• pp.680-685
• /
• 2006

This paper describes the aeroelastic stability test of the small-scaled 'Next-Generation Blade(NRSB)' with NRSH (Next-Generation Hub System) and HCTH hingeless hub system in hover and forward flight conditions. Excitation tests of rotor system installed in GSRTS(General Small-scale Rotor Test System) at KARI(Korea Aerospace Research Institute) were tarried out to get lead-lag damping ratio of blades with flexures as hub flexure. MBA(Moving Block Analysis) technique was used for the estimation of lead-lag damping ratio. First, NRSB-1F blades with HCTH hub system, Then NRSB-1F with NRSH hub system were tested. Second, NRSB-2F blades with NRSH hub system were tested. Tests were done on the ground and in the wind tunnel according to the test conditions of hover and forward flight, respectively. Non-rotating natural frequencies, non-rotating damping ratios and rotating natural frequencies were showed similar level fir each cases. Estimated damping ratios of NRSB-1F, NRSB-2F with HCTH and NRSH were above 0.5%, and damping ratio increased by collective pitch angle increasement. Furthermore damping ratios of NRSB-2F were higher than damping ratios of NRSB-1F in high pitch angle. It was confirmed that the blade design for noise reduction would give observable improvement in aeroelastic stability compared to paddle blade and NRSB-1F design.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.16 no.8 s.113
• /
• pp.848-856
• /
• 2006

This paper describes the aeroelastic stability test of the small-scaled 'Next-generation Blade(NRSB)' with NRSH (next-generation hub system) and HCTH hingeless hub system in hover and forward flight conditions. Excitation tests of rotor system installed in GSRTS (general small-scale rotor test system) at KARI (Korea Aerospace Research Institute) were carried out to get lead-lag damping ratio of blades with flexures as hub flexure. MBA(moving block analysis) technique was used for the estimation of lead-lag damping ratio. First, NRSB-1F blades with HCTH hub system, then NRSB- 1F with NRSH hub system were tested. Second, NRSB-2F blades with NRSH hub system were tested. Tests were done on the ground and in the wind tunnel according to the test conditions of hover and forward flight, respectively. Non-rotating natural frequencies, non-rotating damping ratios and rotating natural frequencies were showed similar level for each cases. Estimated damping ratios of NRSB-1F, NRSB-2F with HCTH and NRSH were above 0.5%, and damping ratio increased by collective pitch angle increasement. Furthermore damping ratios of NRSB-2F were higher than damping ratios of NRSB-1F in high Pitch angle. It was confirmed that the blade design for noise reduction would give observable improvement in aeroelastic stability compared to paddle blade and NRSB-1F design.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.33A no.2
• /
• pp.122-130
• /
• 1996

In an effort to learn more about the reaction mechanisms which lead to the compound nucleation at the interface of cobalt and silicon, electrical noise properties has been investigated for cobalt thin films deposited on silicon substrates by the electron beam evaporation and rf sputtering techniques. Microstructural variations at the Co/Si interfaces have been observed by transmission electronmicroscopy. Amorphous structures are observed at the Co/Si interfaces for samples whose cobalt thicknesses are less than 4nm and a polycrystalline compound nucleation has been occurred for thicker films. 1/f noise power same samples, and the spetral density has been normalized. The amplitude of 1/f noise power spectral density shows a gradual increase as the cobalt thickness is increased, and the amplitude has dropped abruptly after the compound nucleation. The variations of the noise parameters areassumed to be an indiction of the phase transformation along the nucleation reaction path, and amplitude has been interpreted as instabilities of the Co/Si interfacial structures.

• Research in Community and Public Health Nursing
• /
• v.16 no.1
• /
• pp.59-67
• /
• 2005

This study was to investigate knowledge, attitude and the preventive behaviour of noise of workers exposed to harmful noise and to provide primary data for noise-exposed workers' hearing conservation and the prevention of noise induced hearing loss. Method: The subjects were 104 workers who participated voluntarily in the questionnaire. The instrument used in this study was knowledge, attitude and practice on noise-induced hearing loss tool by Rhee & Yi (1996). The data were collected from August to September, 2002 with a self-administered questionnaire. Data were analyzed by SPSS 10.0 win program for finding frequency, percentage, mean, standard deviation, t-test, and ANOVA. Results: The average age of workers was 35.9 and the current average year of working at the noise place was $5{\sim}$10 years. In the group of previous noise-exposed workers, they showed significant difference in preventive behaviors (t=4.087, p=.048). In the group of current noise-exposed workers, they showed significant difference in recognition and attitude of noise(F=4.707, p=.004). Also, the duration of wearing ear protection equipment(t=2.383, p=.019), the feeling of wearing ear protection equipment(F=3.602, p=.031) and comfortable sense of wearing ear protection (F=3.919, p=.023) was significant in the preventive behaviour of noise. Conclusion: Considering the results above, we can recognize that there are close relations among the knowledge, attitude and the preventive behaviour of noise. Therefore, it is necessary to develop education - programs for noise-exposed workers' better understanding of noise and preventive behaviors