• Food Science of Animal Resources
• /
• v.33 no.3
• /
• pp.390-394
• /
• 2013

The aim of this study was to determine the optimal storage condition of pre-packed Hanwoo beef without freezing. Hanwoo loin was purchased from a local distributor at 48 h after slaughter, then sliced in $1.5{\pm}0.5$ cm thickness, and packed in a polyethylene (PE) tray covered with linear low-density polyethylene (LLDPE) film. The studied factors to set the optimal storage condition were chamber temperature (5, 2.5 and $-1^{\circ}C$ for 14 d), cooling method (direct and indirect cooling system), and ultraviolet (UV) light irradiation for beef surface sterilization (0, 30, 60, and 120 min). The changes of pH, thiobarbituric acid reactive substances (TBARS) and number of aerobic bacteria were measured during storage. Beef samples stored in $-1^{\circ}C$ showed the minimal increasing rate in TBARS and microbial growth. After 15 d of storage, there was no significant difference in pH and TBARS values. However, the microbial population of beef stored in direct type cooling chamber ($4.25{\pm}0.66$ Log CFU/g) was significantly lower than that of beef stored in indirect type chamber ($6.47{\pm}0.08$ Log CFU/g) (p<0.05). After 4 d of storage, 60 or 120 min UV light irradiated beef samples showed significantly lower microbial population, and at 14 d of storage, 60 min UV irradiated beef sample showed significantly lower microbial population ($3.14{\pm}0.43$ Log CFU/g) than control ($4.46{\pm}0.13$ Log CFU/g) (p<0.05). However, TBARS values of 60 or 120 min UV light irradiated beef samples were significantly higher than non-irradiated beef sample after 4 d of storage (p<0.05).

• Korean Journal of Materials Research
• /
• v.18 no.4
• /
• pp.204-210
• /
• 2008

$1.5\;{\mu}m$-thick copper films deposited on silicon wafers were successfully bonded at $415^{\circ}C$/25 kN for 40 minutes in a thermo-compression bonding method that did not involve a pre-cleaning or pre-annealing process. The original copper bonding interface disappeared and showed a homogeneous microstructure with few voids at the original bonding interface. Quantitative interfacial adhesion energies were greater than $10.4\;J/m^2$ as measured via a four-point bending test. Post-bonding annealing at a temperature that was less than $300^{\circ}C$ had only a slight effect on the bonding energy, whereas an oxygen environment significantly deteriorated the bonding energy over $400^{\circ}C$. This was most likely due to the fast growth of brittle interfacial oxides. Therefore, the annealing environment and temperature conditions greatly affect the interfacial bonding energy and reliability in Cu-Cu bonded wafer stacks.

• Asia pacific journal of information systems
• /
• v.23 no.3
• /
• pp.25-53
• /
• 2013

This study analyzes the effect of Computer Aided Innovation (CAI) to improve R&D Capabilities empirically. Survey was distributed by e-mail and Google Docs, targeting CTO of 235 SMEs. 142 surveys were returned back (rate of return 60.4%) from companies. Survey results from 119 companies (83.8%) which are effective samples except no-response, insincere response, estimated value, etc. were used for statistics analysis. Companies with less than 50billion KRW sales of entire researched companies occupy 76.5% in terms of sample traits. Companies with less than 300 employees occupy 83.2%. In terms of the type of company business Partners (called 'partners with big companies' hereunder) who work with big companies for business occupy 68.1%. SMEs based on their own business (called 'independent small companies') appear to occupy 31.9%. The present status of holding IT system according to traits of company business was classified into partners with big companies versus independent SMEs. The present status of ERP is 18.5% to 34.5%. QMS is 11.8% to 9.2%. And PLM (Product Life-cycle Management) is 6.7% to 2.5%. The holding of 3D CAD is 47.1% to 21%. IT system-holding and its application of independent SMEs seemed very vulnerable, compared with partner companies of big companies. This study is comprised of IT infra and IT Utilization as CAI capacity factors which are independent variables. factors of R&D capabilities which are independent variables are organization capability, process capability, HR capability, technology-accumulating capability, and internal/external collaboration capability. The highest average value of variables was 4.24 in organization capability 2. The lowest average value was 3.01 in IT infra which makes users access to data and information in other areas and use them with ease when required during new product development. It seems that the inferior environment of IT infra of general SMEs is reflected in CAI itself. In order to review the validity used to measure variables, Factors have been analyzed. 7 factors which have over 1.0 pure value of their dependent and independent variables were extracted. These factors appear to explain 71.167% in total of total variances. From the result of factor analysis about measurable variables in this study, reliability of each item was checked by Cronbach's Alpha coefficient. All measurable factors at least over 0.611 seemed to acquire reliability. Next, correlation has been done to explain certain phenomenon by correlation analysis between variables. As R&D capabilities factors which are arranged as dependent variables, organization capability, process capability, HR capability, technology-accumulating capability, and internal/external collaboration capability turned out that they acquire significant correlation at 99% reliability level in all variables of IT infra and IT Utilization which are independent variables. In addition, correlation coefficient between each factor is less than 0.8, which proves that the validity of this study judgement has been acquired. The pair with the highest coefficient had 0.628 for IT utilization and technology-accumulating capability. Regression model which can estimate independent variables was used in this study under the hypothesis that there is linear relation between independent variables and dependent variables so as to identify CAI capability's impact factors on R&D. The total explanations of IT infra among CAI capability for independent variables such as organization capability, process capability, human resources capability, technology-accumulating capability, and collaboration capability are 10.3%, 7%, 11.9%, 30.9%, and 10.5% respectively. IT Utilization exposes comprehensively low explanatory capability with 12.4%, 5.9%, 11.1%, 38.9%, and 13.4% for organization capability, process capability, human resources capability, technology-accumulating capability, and collaboration capability respectively. However, both factors of independent variables expose very high explanatory capability relatively for technology-accumulating capability among independent variable. Regression formula which is comprised of independent variables and dependent variables are all significant (P<0.005). The suitability of regression model seems high. When the results of test for dependent variables and independent variables are estimated, the hypothesis of 10 different factors appeared all significant in regression analysis model coefficient (P<0.01) which is estimated to affect in the hypothesis. As a result of liner regression analysis between two independent variables drawn by influence factor analysis for R&D capability and R&D capability. IT infra and IT Utilization which are CAI capability factors has positive correlation to organization capability, process capability, human resources capability, technology-accumulating capability, and collaboration capability with inside and outside which are dependent variables, R&D capability factors. It was identified as a significant factor which affects R&D capability. However, considering adjustable variables, a big gap is found, compared to entire company. First of all, in case of partner companies with big companies, in IT infra as CAI capability, organization capability, process capability, human resources capability, and technology capability out of R&D capacities seems to have positive correlation. However, collaboration capability appeared insignificance. IT utilization which is a CAI capability factor seemed to have positive relation to organization capability, process capability, human resources capability, and internal/external collaboration capability just as those of entire companies. Next, by analyzing independent types of SMEs as an adjustable variable, very different results were found from those of entire companies or partner companies with big companies. First of all, all factors in IT infra except technology-accumulating capability were rejected. IT utilization was rejected except technology-accumulating capability and collaboration capability. Comprehending the above adjustable variables, the following results were drawn in this study. First, in case of big companies or partner companies with big companies, IT infra and IT utilization affect improving R&D Capabilities positively. It was because most of big companies encourage innovation by using IT utilization and IT infra building over certain level to their partner companies. Second, in all companies, IT infra and IT utilization as CAI capability affect improving technology-accumulating capability positively at least as R&D capability factor. The most of factor explanation is low at around 10%. However, technology-accumulating capability is rather high around 25.6% to 38.4%. It was found that CAI capability contributes to technology-accumulating capability highly. Companies shouldn't consider IT infra and IT utilization as a simple product developing tool in R&D section. However, they have to consider to use them as a management innovating strategy tool which proceeds entire-company management innovation centered in new product development. Not only the improvement of technology-accumulating capability in department of R&D. Centered in new product development, it has to be used as original management innovative strategy which proceeds entire company management innovation. It suggests that it can be a method to improve technology-accumulating capability in R&D section and Dynamic capability to acquire sustainable competitive advantage.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.29 no.4
• /
• pp.328-333
• /
• 1984

Variation in ploidy level of regenerated plants from rice anthers and effective diploidization methods of haploid plants were studied to obtain basic information in rice breeding through anther culture. In a total of 574 plants derived from anther culture using 14F$_1$ hybrids as materials, there were 49.7% haploids, 48.6% diploids and 1.7% polyploids, respectively. The frequency of haploids in Japonica/Indica crosses was 60.6%, and that of Japonica/Japonica crosses was 43.0% in average. Inclusion of 2.4-D or NAA as phytohormone may increase the frequency of haploids, but kinetin may increase the frequency of diploids. The rate of auto-diploidization by tiller separation of haploid plants showed 8.2% in average. The rate of diploidization by leaf-sheath injection of colchicine showed 18.8% in average. Morphological characters of haploids plants showed that 64.6% in culm length, 63.4% in panicle length, 68% in flag leaf length, and 74.4% in flag leaf width compared to diploid plants. These apparent morphological differences will contribute to identify the ploidy of plants derived from rice anther culture.

• Asian-Australasian Journal of Animal Sciences
• /
• v.19 no.11
• /
• pp.1561-1565
• /
• 2006

The objective of this study was to investigate the anti-oxidative effects of taurine on sperm characteristics for in vitro storage of boar semen. Semen was randomly divided into 10 groups in conical tubes and treated with different concentrations of taurine (25-100 mM) with or without $250{\mu}M$ $H_2O_2$. The percentage of motile spermatozoa in taurine groups after 6 and 9 h were significantly higher at >94% and 87%, respectively, compared to the control group ($85.1{\pm}0.5$ and $72.4{\pm}0.3$, p<0.05). The sperm motility in taurine with $H_2O_2$ after 6 h incubation was slightly decreased compared to the taurine alone treatment, but after 9 and 12 h incubation % sperm motility dropped sharply in taurine with $H_2O_2$ ($75.3{\pm}0.3$ and $69.6{\pm}2.9$, p<0.05). For 3, 9 and 12 h incubation, sperm viability in the control was lower than in taurine groups, irrespective of taurine concentration. In eosin Y and nigrosin staining (ENS), the sperm survival rates (%) for 6 h incubation were significantly higher in 25 mM ($76.0{\pm}0.6$) and 50 mM taurine groups ($78.0{\pm}0.7$), respectively. Sperm survival rates for 9 and 12 h incubation were higher in taurine groups (${\geq}48%$ in 9 h and ${\geq}42%$ in 12 h) compared to controls ($43.0{\pm}2.1$ and $31.0{\pm}0.6$, respectively). In the hyoosmotic swelling test (HOST), sperm membrane integrity was similar to the results of sperm survival. These experiments indicate that supplementation of taurine to the semen extender can increase the sperm characteristics(motility, viability, survival and membrane integrity).

• Natural Product Sciences
• /
• v.20 no.4
• /
• pp.274-280
• /
• 2014

Six compounds were isolated from the n-BuOH fraction of the aerial parts of Aruncus dioicus var. kamtschaticus including: sambunigrin (1), prunasin (2), aruncide A (3), aruncide C (4), 1-O-caffeoyl-${\beta}$-D-glucopyranose (5), and caffeic acid (6). Their structures were confirmed by comparing the spectral data with those reported in the literature. The isolated compounds (1 - 6) were then examined for their cytotoxic effects towards MCF-7, HL-60, and HeLa cancer cell lines, as well as their DPPH radical scavenging activity. The results indicated that compound 4 possessed the strongest inhibitory effect toward HeLa cell line with $IC_{50}$ value of $5.38{\pm}0.92{\mu}M$. Compound 3 possessed selective cytotoxic activity on HL-60 cells with $IC_{50}$ value of $6.27{\pm}0.17{\mu}M$, compound 5 was found as the best in inhibiting proliferation with $IC_{50}$ value of $2.25{\pm}0.09{\mu}M$, and the other compounds showed significant inhibition with $IC_{50}$ values ranging from 6.10 to $11.27{\mu}M$. Compound 5 also displayed the strongest cytotoxic effect toward MCF-7 cell line ($IC_{50}$ $4.32{\pm}0.15{\mu}M$). Both 5 and 6 demonstrated strong radical scavenging activity ($IC_{50}$ $6.87{\pm}0.03$ and $4.33{\pm}0.22{\mu}M$, respectively). Compounds 1 and 5 were isolated for the first time from this plant.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.4 no.4
• /
• pp.25-36
• /
• 1984

This paper checked up the safety criteria of the steel structural members by LRFD. And it calculated the resistance and load modulus for it by the proposed method, considering our circumstance, by establisting the taget relability index (${\beta}_0$), and compared their calculated modulus with the nominal safety factors of the road-bridge code and analyzed them. Uncertain quantity measurements fnr the resistance of the steel structural members and for the load effect are due to the method of the uncertain quantity analysis of the load and the resistance, of Galambos-Ravindra and SGST. The summary of the results is as follows: 1) Considering our circumstance, taget relibility index(${\beta}_0$) for current steel structural members are appropriate ${\beta}_0=3.5$. 2) Nominal resistance ${\Phi}^{\prime}$ of the strength design formula for 1) and nominal load modulus ${\gamma}_i^{\prime}$ are as follows; a) Both-sides support plate: ${\Phi}{^{\prime}}=0.75$, ${\gamma}_0{^{\prime}}=1.04$, ${\gamma}_L{^{\prime}}=2.08$ b) One-side support plate: ${\Phi}{^{\prime}}=0.82$, ${\gamma}_0{^{\prime}}=1.04$, ${\gamma}_L{^{\prime}}=2.11$.

• Korean journal of food and cookery science
• /
• v.28 no.1
• /
• pp.67-76
• /
• 2012

This study examined the optimal ingredient mixing ratio for the preparation of steamed cake containing mugwort (Artemisia princeps var. orientalis) powder. After preliminary studies, the following ingredient ranges were determined; 110~129% sugar, 3~8% mugwort powder, 10~25% oil. Among the different mixture designs, the D-optimal design was chosen for analysis. The results of F-test, specific gravity, viscosity, volume and color values (L, a, b), hardness decided a linear model, while the sensory characteristics (color, taste, texture and overall acceptance) decided a quadratic model. The fitness analysis results showed that in all characteristic, the probabilities were significant within 0.05%; thus, the models were accepted as appropriate. The response surface and trace plot results showed that increasing amounts of mugwort powder decreased the brightness, and increased redness and yellowness. As the level of added oil increased, the softness of the cake increased. Cake samples received low sensory evaluation scores when sugar, mugwort powder, and oil were added above their optimal levels. The optimum formulations by the numerical and graphical methods, were similar, and with the numerical method presented as: sugar, mugwort powder, and oil at 120.7%, 5.1%, and 16.2%, respectively(flour weight basis). The above results demonstrate the feasibility of adding mugwort powder to sponge cake, and therefore, the commercialization of mugwort powder cake marketed as a functional food is deemed possible.

• Journal of Information Management
• /
• v.39 no.2
• /
• pp.1-25
• /
• 2008

This study is to investigate the user behavior of defense development and test researchers working for A research institute to provide advanced library services. Based on the prior studies about the subject, survey through questionnaires were conducted, and the data analyzed using SPSS 12.0. Results of the analyses are as follows: The researchers generally gathered information 2 to 3 times per month. The major reason for information gathering was to solve problems and do their tasks. They considered accuracy of information as the most important factor when they gather information. Finding and selecting information sources were the most difficult task for them in retrieving, acquiring and using information. They have most frequently used digital materials (67%), printed materials next (26%), and non-book materials (6%). Internet was both the most frequently used and most satisfied information source for the researchers.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.46 no.2
• /
• pp.157-163
• /
• 2010

The indirect target strength (TS) estimation method which uses the Kirchhoff ray mode model (KRM model) was discussed to apply for a biomass estimation in the water of mixed species. TS of 25 live scorpion fishes for 120kHz were measured by a tethered method and of others dominant 5 species in the marine ranching ground of Jeju coastal water including a scorpion fish were also estimated by KRM model. The measurement TS of scorpion fish well agreed with the theoretical values and the standard formula of scorpion fish was estimated as $TS_{120kHz}=20Log\;(L)-72.9$ ($r^2=0.67$). TScm values estimated on trial to each sample of dominant 5 species were from -69.3dB to -75.1dB at 120kHz and they were in the general range of swimbladdered fish. It was clarified that TS by KRM model can be used to estimate fish biomass estimation by increasing a sample number and is more effective under the condition that there is rare TS information for inhabiting species in mixed-species area.