• Resources Recycling
• /
• v.27 no.2
• /
• pp.48-54
• /
• 2018

Batch ion exchange experiments of Au(III) were performed from ammonium chloride solution by employing strong anionic exchange resins (Amberlite IRA 402 and AG 1-X8). Au(III) was well loaded into the two resins and the loading behavior of Au(III) into AG 1-X8 was superior to that into Amberlite IRA 402. The loading of Au(III) into AG 1-X8 followed Langmuir adsorption isotherm and the experimentally determined loading capacity was 355 mg/g. Au(III) was successfully eluted by $HClO_4$ from the loaded AG 1-X8 and the elution percentage of Au(III) increased with the concentration of $HClO_4$.

• Resources Recycling
• /
• v.28 no.2
• /
• pp.54-61
• /
• 2019

In order to recover pure alumina from black dross, leaching of mechanically activated black dross with NaOH solution resulted in an aluminate solution containing a small amount of Si(IV). Selective adsorption of Si(IV) onto hydrotalcite was investigated from 5 M NaOH solution where the concentration of Al(III) and Si(IV) was 13000 and 150 mg/L, respectively. Only Si(IV) was selectively loaded onto hydrotalcite, while Al(III) remained in the solution. Effect of the calcination treatment of hydrotalcite and concentration of calcined hydrotalcite and NaOH on the loading of Si(IV) was investigated. Although the loading percentage of Si(IV) was low from 5 M NaOH solution, most of the Si(IV) was removed by adjusting the concentration of NaOH by 48 times dilution with water when the concentration of calcined hydrotalcite was higher than 4.5 g/L. The loading of Si(IV) onto calcined hydrotalcite followed Freundlich adsorption isotherm.

• Clean Technology
• /
• v.19 no.4
• /
• pp.370-378
• /
• 2013

This review has shown the capability of MOFs and ZIFs materials to adsorb $CO_2$ under typical PSA temperatures and pressures. The usual operating conditions are adsorption temperatures of $15{\sim}40^{\circ}C$ and adsorption pressures of 4~6 bar based on numerous PSA processes which are widely employed in gases industry for adsorptive separation of $CO_2$. The extent of $CO_2$ adsorption on the microporous materials depends on the metal species and organic linkers existing in the frameworks. The pore size and the surface area, and the process variables are the key parameters to be associated with the efficiency of the adsorbents, particularly adsorption pressures if other variables are comparable each other. The MOFs and ZIFs materials require high pressures greater than 15 bar to yield significant $CO_2$ uptakes. They possess a $CO_2$ adsorption capacity which is very similar to or less than that of conventional benchmark adsorbents such as zeolites and activated carbons. Consequently, those materials have been much less cost-effective for adsorptive $CO_2$ separation to date because of very high production price and the absence of commercially-proven PSA processes using such new adsorbents.

• Applied Chemistry for Engineering
• /
• v.33 no.2
• /
• pp.151-158
• /
• 2022

In this paper, parameter characteristics such as pH effect, isotherm, kinetic and thermodynamic parameters and competitive adsorption of dyes including malachite green (MG), direct red 81 (DR 81) and thioflavin S (TS), which have different functional groups, being adsorbed onto activated carbon were investigated. Langmuir, Freundlich and Temkin isotherm models were employed to find the adsorption mechanism. Effectiveness of adsorption treatment of three dyes by activated carbon were confirmed by the Langmuir dimensionless separation factor. The mechanism was found to be a physical adsorption which can be verified through the adsorption heat calculated by Temkin equation. The adsorption kinetics followed the pseudo second order and the rate limiting step was intra-particle diffusion. The positive enthalpy and entropy changes showed an endothermic reaction and increased disorder via adsorption at the S-L interface, respectively. For each dye molecule, negative Gibbs free energy increased with the temperature, which means that the process is spontaneous. In the binary component system, it was found that the same functional groups of the dye could interfere with the mutual adsorption, and different functional groups did not significantly affect the adsorption. In the ternary component system, the adsorption for MG lowered a bit, likely to be disturbed by the other dyes meanwhile DR 81 and TS were to be positively affected by the presence of MG, thus resulting in much higher adsorption.

• Proceedings of the Korean Fiber Society Conference
• /
• 2003.10b
• /
• pp.231-232
• /
• 2003

산성염료는 양모나 나일론 등 폴리아미드 섬유에 염착을 하여 염색이 되는 염료이다. 산성염료의 염색 견뢰도를 증가시키기 위해서는 금속매염을 이용하는 경우와 함금속 산성염료를 사용하는 방법이 있다[1-21. 특히 나일론의 경우는 산성염료로 염색시 낮은 흡착률과 견뢰도측면에서 많은 문제점이 발생하고 있다. 이 연구에서는 크롬, 코발트 등의 금속을 함유하고 있는 다양한 구조의 함금속 산성염료를 합성하고 염색성과 견뢰도를 조사하였다. (중략)

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.240-240
• /
• 2013

PLS-II 저장링 진공시스템의 주 배기 장치로 설치되어 운용되고 있는 조합펌프(NEG+이온펌프)의 성능을 측정하였다. 이 조합펌프는 60 l/s 또는 30 l/s의 이온펌프와 WP950 (ZrVFe) getter module (1~3개)로 구성되어 있다. 이 펌프의 배기속도를 활성화 방법에 따라 측정하여 성능을 검증하고 재활성화 빈도, 흡착률을 실험적으로 측정하였다. 배기속도는 수소, 일산화탄소, 수소+일산화탄소의 혼합기체를 사용하여 측정하여 보고하고자 한다.

• Analytical Science and Technology
• /
• v.15 no.2
• /
• pp.163-171
• /
• 2002

The adsorption characteristics of Cd(II) and Pb(II) ions has been studied by using chitin as an adsorbent. The pure chitin was obtained from the extraction of red-crab shell dumped by fish factory. Adsorption kinetics of Cd(II) and Pb(II) ions on the chitin reached at the maximum adsorption within two minutes. Adsorbed amounts of heavy metals were pH 7.0>10.5>3.5 in the following order. Adsorption ratio by chitin was 21${\sim}$99% for Cd(II) ion and 24${\sim}$95% for Pb(II) ion. Recovery ratio of Cd(II) ion on the chitin was 22${\sim}$53%, and that of Pb(II) ion was 22${\sim}$73%. The adsorption behavior of these heavy metals was explained well by Freundlich adsorption isotherm.

• Clean Technology
• /
• v.27 no.3
• /
• pp.261-268
• /
• 2021

Equilibrium, kinetics, and thermodynamics of adsorption of acid black 1 (AB1) by coal-based granular activated carbon (CGAC) were investigated with the adsorption variables of initial concentration of dye, contact time, temperature, and pH. The adsorption reaction of AB1 by activated carbon was caused by electrostatic attraction between the surface (H⁺) of activated carbon and the sulfite ions (SO₃^-) and nitrite ions (NO₂^-) possessed by AB1, and the degree of reaction was highest at pH 3 (97.7%). The isothermal data of AB1 were best fitted with Freundlich isotherm model. From the calculated separation factor (1/n) of Freundlich, it was confirmed that adsorption of AB1 by activated carbon could be very effective. The heat of adsorption in the Temkin model suggested a physical adsorption process (< 20 J mol^-1). The kinetic experiment favored the pseudo second order model, and the equilibrium adsorption amount estimated from the model agreed to that given by the experiments (error < 9.73% ). Intraparticle diffusion was a rate controlling step in this adsorption process. From the activation energy and enthalpy change, it was confirmed that the adsorption reaction is an endothermic reaction proceeding with physical adsorption. The entropy change was positive because of an active reaction at the solid-liquid interface during adsorption of AB1 on the activated carbon surface. The free energy change indicated that the spontaneity of the adsorption reaction increased as the temperature increased.

• Proceedings of the SAREK Conference
• /
• 2005.11a
• /
• pp.341-346
• /
• 2005

Nowadays, adsorption chillers have been receiving considerable attentions as they are energy-saving and environmental1y benign systems. A Fin & tube type heat exchanger in which adsorption/desorption take place is required more compact size. The adsorption chiller is expected to have high energy-efficiency in utilizing the waste heat exhausted from a process. The objectives of this paper are to investigate the effect of fin pitch of fin & tube on the adsorption performance and to develop an optimal design fin & tube heat exchanger in the silica gel/water adsorption chiller. Previous study concluded that optimal particle size selected 0.5mm, type HO silica gel, and fundamental heat transfer & mass transfer experiments carried out. From the numerical results, the adsorption rate for the fin pitch 2.5mm is the highest than that for the fin pitch 5mm, 7.5mm and 10mm. Also cooling water & hot water temperature affect the adsorption rate.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.12
• /
• pp.592-599
• /
• 2018

The kinetics and thermodynamics of the adsorption of acid blue 40 from an aqueous solution by activated carbon were examined as a function of the activated carbon dose, pH, temperature, contact time, and initial concentration. The adsorption efficiency in a bathtub was increased at pH 3 and pH 11 due to the presence of sufonate ions ($SO_3{^-}$) and amine ions ($NH_2{^+}$). The equilibrium adsorption data were fitted to the Langmuir, Freundlich and Temkin isotherms. The results indicated that the Langmuir model provides the best correlation of the experimental data. The separation factor of the Langmuir and Freundlich model showed that the adsorption treatment of acid blue 40 by activated carbon could be an effective adsorption process. The adsorption energy determined by the Temkin equation showed that the adsorption step is a physical adsorption process. Kinetics analysis of the adsorption process of acid blue 40 on activated carbon showed that a pseudo second order kinetic model is more consistent than a pseudo second order kinetic model. The estimated activation energy was 42.308 kJ/mol. The enthalpy change (80.088 J/mol) indicated an endothermic process. The free energy change (-0.0553 ~ -5.5855 kJ/mol) showed that the spontaneity of the process increased with increasing adsorption temperature.