• Journal of Advanced Marine Engineering and Technology
• /
• v.28 no.3
• /
• pp.457-465
• /
• 2004

Environmental protection on the ocean has been interested and nowadays the International Maritime Organization(IMO) has advanced on the prevention of air pollution from ships. This study presents the performance and the emission characteristics of 4 stroke marine diesel engines for generation application in D2 cycle(IMO mode). The effects of important operating parameters, such as intake air pressure. intake air temperature and maximum combustion pressure on NOx emissions were also described. Emissions measurement and calculation are processed according to IMO Technical Code. The results show that the maximum combustion pressure by fuel injection timing control and intake air temperature has strong influence on NOx emission production. But NOx emission is not affected by intake air pressure and exhaust gas back pressure.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2002.05a
• /
• pp.121-127
• /
• 2002

Environmental protection on the ocean has been interested and nowadays the International Maritime Organization(IMO) has advanced on the prevention of air pollution from ships. This study presents the emission characteristics of 4 stroke propulsion diesel engine in E2 cycle (constant speed) and E3 cycle (propeller curved speed). Also the effects of important operating parameters in terms of intake air pressure and temperature, and maximum combustion pressure are described on the specific emissions. Emissions measurement and calculation are processed according to IMO Technical Code. The results show that NOx emission level in E3 cycle is higher than E2 cycle due to lower engine speed and lower maximum combustion pressure by retarding fuel injection timing. Intake air temperature has strong influence on NOx emission production. And CO, HC emissions are not affected by maximum combustion pressure and intake air pressure and temperature.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.47 no.1
• /
• pp.17-25
• /
• 2019

An intake of Aircraft becomes S-shaped geometry due to spatial limitation or procuring survivability. But curvature of the S-shaped geometry makes secondary flow or flow separation which is the cause of non-uniform pressure distribution. In this study, boundary layer suction is applied to RAE M 2129 S-Duct by attaching sub duct. Design variable is suction location and angle. A mass flow rate drawn out by suction at the sub duct outlet is constant over every model. A grid dependency test was conducted to verify validity of computation. The comparison among the CFD (Computation Fluid Dynamics), ARA experimental result, and ARA computation result of non-dimensional pressure distribution on the Port side and Starboard Side confirmed the validity of CFD. In this study, Distortion Coefficient was used for evaluating aerodynamic performance of S-Duct. The analysis, which was about flow separation, vortex, mass flow rate distribution, and pressure distribution were also investigated. Maximum 26.14% reduction in Distortion Coefficient was verified.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.34 no.10
• /
• pp.61-70
• /
• 2006

A Supersonic air intake model was designed for the high performance ramjet and dual-mode scramjet engine to operate at Mach 4 flight condition. The air intake was tested in the blowdown-type wind tunnel of Kyushu University to identify the internal flow characteristics corresponding to the flight parameters such as the back pressure, angle of attack and angle of yaw. Flow visualization was achieved by the Schlieren and oil flow visualization techniques. The intake performance was analyzed quantitatively based on the surface pressure and total Pressure measurements. The experimental results were compared with the computational fluid dynamics results. The present study exhibits the fundamental but rarely found experimental results of the high Mach number supersonic air intake.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2006.11a
• /
• pp.331-335
• /
• 2006

Theoretically, stable operations of an inlet are achieved at the design condition. However, at off-design conditions supersonic inlets often encounter the problem of aerodynamic instability, called inlet buzz. During inlet buzz, supersonic inlets exhibit considerable oscillation of the shock system in front of the inlet and corresponding large pressure fluctuations downstream. This phenomenon results in decrease of engine performance. An experimental and numerical study was conducted to investigate the phenomenon of supersonic inlet buzz on a generic, axisymmetric, external-compression inlet with a single-surface center-body. This study suggest that intermittent buzz exist and the frequency become to be large as increasing the back pressure.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.33 no.1
• /
• pp.225-228
• /
• 2004

Optimization of fluidized bed granulating conditions for yield, bulk density, and tapped density of powdered milk was determined using response surface methodology. Yield of powdered milk was greatly affected by feeding rate of water, and bulk density and tapped density could be reduced by decreasing of atomization pressure. The optimum conditions for fluidized bed granulating of powdered milk were predicted with 6$0^{\circ}C$ of inlet air temperature, 16 mL/min of feeding rate, and 2.1 bar of atomization pressure. Also 94% of yield 0.350 g/㎤ of bulk density, and 0.446 g/㎤ of tapped density of powdered milk could be obtained by the optimum granulating conditions.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.13 no.4
• /
• pp.55-62
• /
• 2009

Fracture behavior of ceramic dome port cover on air breathing engine using liquid and solid fuel propulsion system was carried out in this study. Fracture characteristics was tested and estimated using scaled model of ceramic dome port cover by Shock tube. Fracture behavior was obtained by the fracture pressure from pressure sensor and observed the scattering phenomena of fracture specimen using high speed camera. Results obtained from this study can be used in the base data of dome port cover design for an air breathing engine.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2000.11a
• /
• pp.14-14
• /
• 2000

가스터빈 연소기의 연소 효율을 높이기 위해서는 연료와 공기의 충분한 혼합이 필요하다. 연료와 흡입되는 공기의 혼합은 큰 스케일의 난류 성분보다는 오히려 연소기내에서 국부적으로 작용하는 작은 스케일의 난류 성분에 크게 지배를 받게된다. 이러한 혼합 촉진을 위해 연료와 공기의 경계면에서의 운동에너지를 증가시키는 방법은 압력의 손실을 가져오게 되지만 혼합의 촉진에 의한 완전연소와 저 NOx화는 더 큰 이익을 가져다 준다.(중략)

• Journal of the Korean Society of Propulsion Engineers
• /
• v.20 no.4
• /
• pp.104-111
• /
• 2016

The flame stabilization is one of the topics which have to be solved for the airbreathing propulsion systems, using the entering air which is supersonic velocity as an oxygen sources. Making a recirculation zone with an eddy flow, installed the reducing velocity devices such as the bluff body, is the typical method of the flame stabilization. Recently using a cavity flame stabilization at the wall is an emerging technique as an effective method which extends the stabilization zone, and the related research papers have been published on the flow separation and reattachment, pressures and oscillations including length/depth ratios in the cavities. Even though, still there are lots of topics to study more in the cavity flame stabilization field as the preceding techniques, as well as the research and the development of the airbreathing propulsion system itself.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.26 no.4
• /
• pp.10-20
• /
• 2022

The performance analysis test of the scramjet engine intake was conducted under the Mach 5 condition of the scramjet engine test facility, a free-jet ground test facility of the Korea Aerospace Research Institute. A pitot/static pressure rake installed at the rear of the isolator was designed and manufactured to measure the total pressure recovery rate and mass capture ratio, which are typical performance factors of the scramjet engine intake. The effect of the rake mounted at the rear of the isolator on the intake, the performance analysis measured by the rake, and the change in wall static pressure distribution according to the angle of attack were performed. Finally, the point at which the intake unstart occurred was confirmed by using the rear back pressure adjusting device, which simulates pressure rise in the combustor, and the results are summarized in this paper.