• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.463-463
• /
• 2010

고휘도 고효율 백색 LED (lighting emitting diode)가 차세대 조명광원으로 급부상하고 있다. 백색 LED를 생산하기 위한 공정에서 MOCVD (유기금속화학증착)장비를 이용한 Epi wafer공정은 에피층과 기판의 격자상수 차이와 열팽창계수차이로 인하여 생성되는 에피결함의 제거를 위하여 기판과 GaN 박막층 사이에 완충작용을 해줄 수 있는 버퍼층 (Buffer layer)을 만들고 그 위에 InGaN/GaN MQW (Multi Quantum Well)공정을 하여 고휘도 고효율 백색 LED를 구현할 수 있다. 이 공정에서 기판의 온도가 불균일해지면 wafer 파장 균일도가 나빠지므로 백색 LED의 yield가 떨어진다. 균일한 기판 온도를 갖기 위한 조건으로 기판과 induction heater의 간격, 가스의 흐름, 기판의 회전, 유도가열코일의 디자인 등이 장비의 설계 요소이다. 코일에 교류전류를 흘려주면 이 코일 안 또는 근처에 있는 도전체에 와전류가 유도되어 가열되는 유도가열 방식은 가열 효율이 높아 경제적이고, 온도에 대한 신속한 응답성으로 인하여 열 손실을 줄일 수 있으며, 출력 온도 제어의 용이성 및 배출 가스 등의 오염 없다는 장점이 있다. 본 연구에서는 유도가열방식의 induction heater를 이용하여 회전에 의한 기판의 온도 균일도 측정을 하였다. 기초 실험으로 저항 가열 히터를 통하여 대류에 의한 온도 균일도를 평가하였다. 그 결과 gap이 3 mm일 때, 평균 온도 $166.5^{\circ}C$ 에서 불균일도 6.5 %를 얻었으며 이를 바탕으로 induction heater와 graphite susceptor의 간격이 3 mm일 때, 회전에 의한 온도 균일도를 측정을 하였다. 가열원은 induction heater (viewtong, VT-180C2)를 사용하였고, 가열된 graphite 표면의 온도를 2차원적으로 평가하기 위하여 적외선 열화상 카메라(Fluke, Ti-10)을 이용하여 온도를 측정하였다. 기판을 회전하면서 표면 온도의 평균과 표준 편차를 측정한 결과 2.5 RPM일 때 평균온도 $163^{\circ}C$ 에서 가장 좋은 5.5 %의 불균일도를 확인할 수 있었고, 이를 상용화 전산 유체 역학 코드인 CFD-ACE+의 모델링 결과와 비교 분석 하였다.

• Plant Journal
• /
• v.17 no.1
• /
• pp.38-49
• /
• 2021

In order to increase power plant efficiency, the steam temperature was increased to 610 ℃ which deteriorates the durability of the boiler tube and as the use of low-calorie coal increases the post combustion and delayed combustion phenomenon, the overheating of the final reheater and the tube rupture are becoming frequent. In order to prevent overheating of the final reheater, desuperheater water injection was increased, leading to a decrease in boiler efficiency. In this study install a baffle plate at the back of some overheated tube groups, thereby reduce the temperature of the tube by reducing the amount of combustion gas, and the reduced combustion gas moves to an adjacent place to increase the temperature of other tubes. As a result of the study, the temperature deviation between tubes decreased 1.5. And the heat-reducing injection amount was reduced to 6,929 kg/h and the maximum tube temperature was reduced to 623.4℃ which is 6.6℃ more below than the control standard of 630℃.

• Journal of the Korea Convergence Society
• /
• v.10 no.10
• /
• pp.99-105
• /
• 2019

In this study, the flow analysis around vehicle was carried out on various kinds of roof box models installed at the roof of vehicle. Through the analysis of fluid flow and pressure, we investigated which model was more suitable for driving. The four types of models were designed with their respective shapes of models 1, ${\beta}$, ${\delta}$ and ${\gamma}$, and the driving speed of car was set as 20 m/s. It was confirmed that the pressure for model ${\beta}$ became greatest compared to other models. And model ${\delta}$ has the lowest pressure among all models of roof boxes by installing a canoe with the structure for cable type. As the design data with the durability of roof box obtained on the basis of this study result are utilized, the esthetic sense can be shown by being grafted onto the car body at real life.

• Journal of the Korean Geosynthetics Society
• /
• v.22 no.1
• /
• pp.1-7
• /
• 2023

This study has utilized self-assembled monolayers technology to improve electrical property of graphene-oxide, which has been seperated graphine powder through a chemical exfoliation. Aluminum sulfate (Al₂(SO₄)₃) was applied on graphene-oxide as a reactant, and the fundamental research was carried out to apply on the self-sensing of cement-based construction structures. Electric resistance measurement result has shown that cement-composites with GO and Al-GO can be used as a conductor, electric resistance of GO and Al-GO contained composites improved by 10.2% and 15.9% respectively when compared to the standard cement-composite. Microstructure analyzation shown the formation of Al(OH)₃ gel when Al-GO was added, which is speculated to result the smooth flow of current by improving the density of cement-composite. This implies that graphene-oxide has a possibility to be utilized as smart building materials and construction structure itself rather than just a structure.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.28 no.5B
• /
• pp.591-594
• /
• 2008

Present study aims at the development of a reasonable boundary condition for a structure over inclined seabed in case of the numerical model with quadrilateral mesh system. The technique for the inclined impermeable/permeable boundary in the quadrilateral mesh is newly proposed. The new technique and LES-WASS-3D model (Hur and Lee, 2007) have been used for the investigation of the dynamics of fluid field, and validated through the comparison with a typical stair-type boundary condition. 3-Dimensional numerical model with Large Eddy Simulation is called LES-WASS-3D, and is able to simulate directly interaction of WAve Structure Sea bed/Sandy beach.

• Composites Research
• /
• v.36 no.6
• /
• pp.388-394
• /
• 2023

In composites manufacturing, increasing resin impregnation is a key way to speed up the manufacturing process and improve product quality. While resin improvement is important, simple fiber surface treatments can also improve resin flowability. In this study, different plasma treatment times were applied to carbon fiber fabrics to improve the impregnation between resin and fiber. Electrical resistivity measurements were used to evaluate the dispersion of resin in the fibers, which changed with plasma treatment. The effect of fiber surface treatment on resin spreadability could be observed in real time. When inserting a carbon fiber tow into the resin, the amount of resin that soaked into the tow was measured to objectively compare resin impregnation. Five minutes of plasma treatment improved the tensile and compressive strength of the composite by more than 50%, while reducing the void content and increasing the fire point impregnation flow rate. Finally, a dynamic flexural fatigue test was conducted using a portion of the composite used as an architectural composite part, and the composite part did not fail after one million cycles of a 3 kN load.

• Korean Chemical Engineering Research
• /
• v.57 no.6
• /
• pp.868-873
• /
• 2019

In this study, the evaluation of performance of AORFB using methyl viologen and TEMPOL as organic active materials in neutral supporting electrolyte (NaCl) with various membrane types was performed. Using methyl viologen and TEMPOL as active materials in neutral electrolyte solution, the cell voltage is 1.37V which is relatively high value for AORFB. Two types of membranes were examined for performance comparison. First, when using Nafion 117 membrane which is commercial cation exchange membrane, only the charge process occurred in the first cycle and the single cell couldn't work because of its high resistance. However, when using Fumasep anion exchange membrane (FAA-3-50) instead of Nafion 117 membrane, the result was obtained as the totally different charge-discharge graphs. When current density was $40mA{\cdot}cm^{-2}$ and cut off voltage range was from 0.55 V to 1.7 V, the charge efficiency (CE) was 97% and voltage efficiency (VE) was 78%. In addition, the discharge capacity was $1.44Ah{\cdot}L^{-1}$ which was 54% of theoretical capacity ($2.68Ah{\cdot}L^{-1}$) at $10^{th}$ cycle and the capacity loss rate was $0.0015Ah{\cdot}L^{-1}$ per cycle during 50 cycles. Through cyclic voltammetry test, it seems that this difference in the performance between the full cell using Nafion 117 membrane and Fumasep anion exchange membrane came from increasing resistance due to chemical reaction between membrane and active material, not the capacity loss due to cross-over of active material through membrane.

• Journal of Wetlands Research
• /
• v.22 no.3
• /
• pp.194-199
• /
• 2020

Unlike in the past, the world is facing water shortages due to climate change and difficulties in simultaneously managing the risks of flooding. The Four Major Rivers project was carried out with the aim of realizing a powerful nation of water by managing water resources and fostering the water industry, and the construction period was relatively short compared to the unprecedented scale. Therefore, the prediction and analysis of how the river environment changes after the Four Major Rivers Project is insufficient. Currently, part of the construction section of the Four Major Rivers Project is caused by repeated erosion and sedimentation due to the effects of sandification caused by large dredging and flood-time reservoirs, and the head erosion of the tributaries occurs. In order to solve these problems, the riverbed maintenance work was installed, but it resulted in erosion of both sides of the river and the development of new approaches and techniques to keep the river bed stable, such as erosion and excessive sedimentation, is required. The water agent plays a role of securing a certain depth of water for the main stream by concentrating the flow so much in the center and preventing levee erosion by controlling the flow direction and flow velocity. In addition, Groyne products provide various ecological environments by forming a natural form of riverbeds by inducing local erosion and deposition in addition to the protection functions of the river bank and embankment. Therefore, after reviewing the method of determining the shape of the Groyne structure currently in use by utilizing the mobile limit flow rate and marginal reflux force, a new Critical Movement Velocity(${\bar{U}}_d$) and a new resistance coefficient formula considering the mathematical factors applicable to the actual domestic stream were developed and the measures applicable to Groyne installation were proposed.

• Journal of Korea Water Resources Association
• /
• v.44 no.10
• /
• pp.819-830
• /
• 2011

The multi-slope MUSCL, proposed by T. Buffard and S. Clain, determines slopes of conserved variables at each edge of a cell in the linear reconstructions of data. In this study, the second order accurate numerical model was developed according to the multi-slope MUSCL to solve the shallow water equations on the unstructured grids. The HLLL scheme of approximate Riemann solvers was used to calculate fluxes. For the review of the applicability of the developed model, the results of the model were compared to the 'isolated building test' and the 'model city flooding experiment' conducted as part of the IMPACT (Investigation of extreMe flood Processes And unCerTainty) project in Europe. There were limitations to predict abrupt rising of water depths by the resistance of model buildings and water depths at the specific locations among the buildings. But they were identified as the same problems also revealed in results of the other models to the same experiment. On the more refined meshes to the 'model city flooding experiment' simulated results showed good agreement with measurements. It was verified that the developed model simulated well the complex phenomena such as a dam-break problem and the urban inundation by flash floods.

• Journal of Korea Water Resources Association
• /
• v.45 no.2
• /
• pp.137-149
• /
• 2012

Field measurements of resistance to flow are analyzed for 739 rivers vegetated with grass (281 channels), shrubs (150 channels) and trees (308 channels). The measured distribution of Manning roughness coefficients ranges from 0.015~0.250 for grass, 0.016~0.250 for shrubs, 0.018~0.310 for trees. Significant trends are obtained between Darcy-Weisbach (or Manning roughness coefficients) and flow discharge, friction slope, and relative submergence. The regression equations for Darcy-Weisbach and Manning roughness coefficients in vegetated rivers are: $f_{veg}=0.436Q^{-0.363}$, $f_{veg}=3.305S_f^{0.508}$, and $n_{veg}=0.061Q^{-0.124}$, $n_{veg}=0.144S_f^{0.199}$, $V=5.3(h/d_{50})^{1/8.3}{\sqrt{ghS_f}}$, $\sqrt{8/f}(=V/u*)=5.75log(5h/d_{50})$, respectively. These semi-empirical relationships should be useful for hydraulic engineering practice.