• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.36 no.11
• /
• pp.1447-1453
• /
• 2012

For an electromagnetic suspension (EMS)-type urban Maglev train using U-shaped electromagnets, both the vertical and the lateral air gaps for levitation are maintained only by the electromagnet. The train can run over curved rails without active lateral air gap control because the U-shaped electromagnet simultaneously produces both a levitation force and a guidance force, which is dependent on the levitation force. Owing to the passive control of the lateral air gap, the lateral vibration could exceed the limits of the lateral air gap and acceleration. In this study, dynamic analysis of a Maglev train is carried out, and the effectiveness of a lateral damper for vibration reduction is investigated. To more accurately predict the lateral vibration, a Maglev vehicle multibody model including air-sparing, guideway irregularities, electromagnets, and their controls is developed.

• Journal of Ocean Engineering and Technology
• /
• v.7 no.1
• /
• pp.73-80
• /
• 1993

본 연구에서는 장주형 해양구조물의 횡방향 진동에 대한 파라메트릭 가진 효과를 고찰하였다. 먼저, 장주형 해양구조물의 횡방향 운동에 대한 4계 편미방지배방정식을 비선형 Mathieu 방정식으로 유도하였다. 비선형 mathieu 방정식의 해를 구하여 장주형 해양구조물의 동적 반응 특성을 해석하였다. 유체 비선형 감쇠력은 불안정 조건하에 있는 파라메트릭 진동의 반응크기를 제한 하는데 중요한 역활을 한다. 파라메트릭 진동의 경우 가장 큰 반응크기는 Mathieu 안정차트의 첫번째 불안정 구간에서 일어난다. 반면에, 파라메트릭 진동과 강제진동의 결합 진동인 경우, 가장 큰 반응 크기는 두번째 불안정 구간에서 발생된다. 파라메트릭 가진으로 인한 장주형 해양구조물의 횡방향 운동은 동적조건에 따라 subharmonic, superharmonic 또는 chaotic 운동이 되기도 한다.

• Journal of Advanced Marine Engineering and Technology
• /
• v.40 no.4
• /
• pp.301-306
• /
• 2016

During the initial stage of propulsion shaft design, the shaft alignment process includes a thorough consideration of lateral vibration to verify the operational safety of the shaft. However, a theoretical method for analyzing forced lateral vibrations has not been clearly established. The methods currently used in classification societies and international standards can only ensure a sufficient margin to avoid the blade-passing frequency resonance speed outside the range of ${\pm}20%$ of the maximum continuous rating (MCR) for the engine. Typically, in shaft alignment analyses, longer center distances between the support bearings promote affirmative results, but the blade order resonance speed can approach the lower limit for lateral vibration. Therefore, this matter requires careful attention by engineers, and a verification of the theoretical analysis by experimental measurements is highly desirable. In this study, both theoretical and experimental analyses were conducted using strain gauges under two draught conditions of vessels used as 50,000-DWT oil/chemical tankers, introduced recently as eco-friendly ships. Based on the analyses, the influence of the lateral vibration on the shafting system and the system's reliability was reviewed.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.12
• /
• pp.797-803
• /
• 2019

This study was carried out to reduce the lateral vibration of high-speed electric multiple units. In the study, the high-speed electric multiple unit prototype (HEMU-430X) has a high lateral vibration at low equivalent conicity regardless of the wheel profiles (XP55, GV40, S1002). As wheel wear progresses and the equivalent conicity increases, the lateral vibration tends to decrease. The reason is that a combination of the suspension characteristics causes the body and bogie to resonate at a frequency of 1.4 Hz when the equivalent conicity is low, resulting in body hunting. An investigation of the lateral vibration of overseas high-speed trains showed that a decrease in the hydraulic stiffness of the yaw damper could improve the vibration. The series stiffness of the yaw damper is a combination of the hydraulic stiffness and elastic joint. In this study, an attempt was made to improve the lateral vibration by lowering the stiffness of the elastic joint. The series stiffness of the adjusted yaw damper was approximately 60% compared to the original one. The on track test results showed improvement in the lateral vibration for both running directions. The vibration reduction method of this study can be used for EMU-250 and EMU-320 in future commercial operations.

• Journal of the KSME
• /
• v.25 no.5
• /
• pp.406-412
• /
• 1985

연소 동안에 크랭크 축은 오일 필름을 통하여 연소압력이 실린더 블록으로 전달된다. 점화 전에 관성력에 의한 크랭크 축의 굽힘 변형은 크랭크 축으로부터 메인 베어링까지의 연소하중 전달에 큰 영향을 미친다. 메인 베어링에 베어링 보를 부착시키거나 크랭크 축의 굽힘 강성을 변화시켜 실린더 블록의 스커어트 진동을 감소시키는 효과를 얻었다. 크랭크 축의 비틂 진 동을 일으키는 회전력과 관성력 변동의 합력은 크랭크 저어널의 횡진동을 일으킨다. 크랭크 축의 횡 강제진동은 베어링 1에서 최대값이기 때문에 실린더 블록의 굽힘, 비듦 진동에 대하여 기진력이 된다. 실린더 블록의 진동 진폭은 관성력 변동의 주파수가 실린더 블록의 공진진 동수에 가까워지는 정도와 크랭크 축 비듦 진동의 진폭에 의존한다. 크랭크 풀리의 극관성 모우멘트와 크랭크 축 비듦 진동을 감소시키는데 효과를 준다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.11a
• /
• pp.37-38
• /
• 2006

본 연구에서는 압전체의 횡 진동모드를 이용한 압전 초음파 진동자를 설계 분석하였다. 이전의 란쥬반 진동자는 진동을 얻기 위하여, 복수의 원판 또는 사각판 형태의 압전 세라믹을 서로 반대 방향으로 분극하여 마주 보도록 설치한 후 전기적으로 병렬로 연결하고 상단 및 하단에 금속부을 부착하여 전체를 볼트로 조인 복잡한 구조와 큰 출력 파워를 갚는 반면, 본 연구에서는 판상형의 압전소자와 일체형 금속진동체를 이용하여 기계적 출력 파워 조절이 용이한 구조의 압전 진동자를 고안하여, 압전진동자의 횡 진동 모드를 이용함으로써 신뢰성과 정확도가 높고 진동효율이 최대가 되도록 설계하였다. 설계 개발된 압전 진동자는 진동의 크기 조절이 용이하여 일반 진동자 뿐 만 아니라, 외과 및 안과 수술에 있어서 인체조직이나 각막상피의 활성화를 유지한 상태에서 안전하게 절개 및 분리 시술용 진동자로 사용 할 수 있는 이점이있다. 압전 진동자는 유한요소법 시뮬레이션 프로그램 (ATILA 5.2.4)을 이용하여 설계를 하였으며 압전소자의 두께는 각각 0.2 mm, 0.5 mm로 제작하여 시뮬레이션 결과와 제작된 샘플의 특성을 비교하였고, 변위측정은 칼날을 결합 한 상태에서 공진 주파수대역 부근 주파수별로 측정 비교하였다.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.11 no.3
• /
• pp.1047-1052
• /
• 2010

Influence of lateral spring constant on energy dissipation and load reduction factor with erespect to lateral vibration of steel sheet pile installed by vibratory pile driver. Energy dissipation and load reduction factor varying with free length of steel sheet pile are more affected by eccentricity than flexural rigidity of steel sheet pile regardless of the magnitudes of lateral spring constants. Load reduction factors were converged when lateral spring constant was equal or larger than 10000N/m.

• Journal of KSNVE
• /
• v.11 no.5
• /
• pp.592-600
• /
• 2001

• Journal of the Korean Society for Railway
• /
• v.15 no.6
• /
• pp.543-549
• /
• 2012

This study describes the tail vibration reduction for the next generation high speed EMU(HEMU-430X). The model of 6 cars was generated and the calculation was performed using VAMPIRE(railway vehicle dynamic software). In view of ride characteristics, HEMU-430X was expected to sway at the tail because of the yaw damper direction. The lateral acceleration of vehicle body exceeded the criteria because of hunting. To reduce this hunting motion, some methods such as wheel profile change, the change of damping coefficient for the 2nd lateral damper, the damping coefficient change of yaw damper were tested, but had little effect. Finally, the yaw damper direction was changed and the tail vibration disappeared. In real running test, the tail vibration appeared at the speed of 150km/h and the yaw damper direction change made the vehicle stable at the speed of 300km/h. The maximum test speed of HEMU-430X is 430km/h. If the tail vibration appears at higher speed, some other methods in this study may be considered to reduce it.

• Computational Structural Engineering
• /
• v.15 no.2
• /
• pp.67-72
• /
• 2002