• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.39 no.1
• /
• pp.123-134
• /
• 2019

This paper proposed a new design equation for the inelastic lateral torsional buckling (LTB) of singly symmetric stepped I-beams with non-compact flange sections. The proposed equation was generated using a finite element program, ABAQUS, and a statistical program, MINITAB. The parameters used were the stepped beams parameters; ${\alpha}$, ${\beta}$, and ${\gamma}$ and the length-to-height ratio ($L_b/h$) of the beam. The proposed equation was further validated by means of experimental test, where beams were subjected to four-point bending and supported by roller and lateral braces near the end supports. In addition, finite element models were simulated using the same parameters used in the experimental test to verify the results of the test conducted. It was proved that LTB capacity calculated from the proposed equation is accurate and conservative in comparison with the yielded values from the FEM and actual test, making it a reliable and safe approach in calculating the buckling capacities of singly symmetric stepped beams with non-compact flange sections.

• Computational Structural Engineering
• /
• v.20 no.1 s.75
• /
• pp.59-64
• /
• 2007

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.31 no.1A
• /
• pp.1-7
• /
• 2011

This paper deals with buckling loads of the column with the constant surface area. The shape function of variable column depth is chosen as the linear taper. The ordinary differential equation governing buckled shapes of the column is derived based on the dynamic equilibrium equation of such column subjected to an axial load. Three kinds of end constraint of hinged-hinged, hinged-clamped and clamped-clamped are considered in numerical examples. Effects of the column parameters on buckling loads are extensively discussed. Especially, section ratios of the strongest column are calculated, under which the maximum, i.e. strongest, buckling loads are achieved. Also the buckled shapes are obtained for searching the nodal points where the inner transverse supports are simply installed to increase the buckling loads.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.14 no.1
• /
• pp.89-93
• /
• 2008

Stiffened panels are basic strength members which have been used widely in a vessel or an offshore. They have been used often a deck, a side and a bottom structure of ship and have a number of one sided stiffener in either one or both directions called grillage. Their buckling and plastic collapse become damaged reason of the hull girder so it needs to investigate accurately buckling and ultimate strength of stiffened panels. In the present paper, using the ANSYS, a commercial finite element analysis code, we conducted the evaluation regarding buckling and post-buckling behaviour of stiffened panels, and analyzed stiffener's web height change, considering the effect of lateral pressure load against compression ultimate strength.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.11 no.2
• /
• pp.1-14
• /
• 1991

A computer program for the linear elastic buckling anlalysis of thin walled members is developed using a 3-node triangular shell element. The element has real stiffness value for a kinematic degree of freedom associated with rotation about the surface normal at each node. The validity of the present computer program is demonstrated through the plate buckling analysis and the lateral-torsional buckling analysis of a straight beam. Then, simply supported circular arches subjected to uniform bending are analyzed and the results are compared with existing solutions.

• Journal of the Korea Concrete Institute
• /
• v.23 no.5
• /
• pp.683-692
• /
• 2011

In piloti-type low-rise RC residential buildings, severe damages have been usually concentrated at piloti stories under the earthquake. In this study, a piloti story was retrofitted by installation of buckling-restrained braces (BRB's) to increase strength and stiffness of piloti story and by application of fiber reinforced polymer (FRP) sheet on columns to avoid the brittle shear and axial failure of columns. To verify this retrofit performance, reversed cyclic lateral load tests were performed on 1:5 scale bare and retrofitted frames. The test results showed that yield strength (43.2 kN) appeared to be significantly larger than design value (30 kN) due to the increase of strength in the compression side, but the stiffness value (11.6 kN/mm) turned out to be approximately one-half of the design value (24.2 kN/mm). The reasons for this difference in stiffness were due to slippage at joint between the frame and the BRB's, displacement and rotation at footing. The energy absorption capacity of the retrofitted frame was 7.5 times larger than that of the bare frame. The change of the number of load cells under the footing from 2 to 1 reduced lateral stiffness from 11.6 kN/mm to 6 kN/mm, which was only three times larger than that of the bare frame (2.1 kN/mm).

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.7 no.1
• /
• pp.63-69
• /
• 2006

New design equations for calculating the lateral-torsional buckling moment resistances of singly stepped I-section beams subjected to general loading on the top flange are suggested based on the investigations of elastic finite-element analyses. The new equations presented in this study are compared with current moment gradient modifiers presented by other researchers and specifications. The study considered almost loading cases on buildings and bridges. The proposed equations should be easily used to calculate the lateral-torsional buckling moment resistance of stepped I-beams.

• Journal of Korean Society of Steel Construction
• /
• v.21 no.3
• /
• pp.321-330
• /
• 2009

This paper presents numerical analysis results for the lateral-torsional buckling (LTB) strength of steel I-girder bridges. Current Korean and AASHTO design specifications for LTB consider the buckling strength of a single girder with both its ends constrained. The I-girder bridges are composed of more than one girder, and the girders are interconnected with intermediate cross-beams or cross-frames. Therefore, it should be required to evaluate the effects of cross-beam stiffness and the interactionof girders on LTB strength. It is also necessary to consider the effects of transverse web stiffeners on LTB strength. By considering these parameters, a series of four-girder systemswere numerically modeled using 3D shell elements to estimate the LTB strength while considering initial imperfections and residual stresses.

• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.4
• /
• pp.163-172
• /
• 2000

The postbuckling behavior and progressive damage of composite laminated cylindrical shell under uniform external pressure were investigated by nonlinear finite element method programming. For the finite element analysis, nine-node 3-D degenerated elements were utilized, and arc-length method including line search was adopted for the iteration and load-increment along postbuckling equilibrium path. As results. buckling load, postbucking behavior, and progressive failure f3r various composite laminated cylindrical shells were discussed.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2003.04a
• /
• pp.219-226
• /
• 2003

보 유사법을 이용하여 연속 압축재의 유효길이 계수를 각 경간별로 결정하는 방법을 제안한다. 제안하는 보 유사법은 4가지 단계로 요약할수 있는데 그 첫 단계는 주어진 압축재를 이것과 동일한 단면성능 및 경간을 갖는 연속보로 치환하는 것이다. 제 2단계에서는 연속보 각 경간의 중앙에 가상 집중 횡하중을 작용시킨 후 이로 인한 지점들에서의 재단 moment를 계산한다. 이때 각 경간중앙의 가상 집중 횡하중 방향은 좌굴 mode를 고려하여 교호로 바뀌도록 한다. 제 3단계에서는 또 하나의 제안식과 재단 모멘트를 이용하여 Kinney의 부분 고정도를 결정한다. 최종단계에서는 부분 고정도를 이용하여 유효길이를 각 경간별로 산정 한다. 제안한 방법은 다 경간 압축재에서 어느 경간이 맨 먼저 좌굴을 일으키는지 또한 이때의 임계하중은 어떤 값을 갖는지를 예측하게 한다.