• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.40 no.5
• /
• pp.521-526
• /
• 2020

Airfield pavements, such as runways and taxiways, are essential for smooth take-off and landing of fixed-wing aircraft and are the most important installation for the military to carry out air operations during wartime. Therefore, in wartime, it is necessary to reduce the damage to these installations and repair them in the shortest possible time. Recently, the pattern of attack is changing from the use of conventional high explosive which is to create large craters to the use of multiple warheads weapon system which is to effectively attack enemy's airfields but unrelated to accuracy. Hence in this study, through identifying the specification and composition of multiple warheads weapon system, we checked the protection performance and damage patterns of the pavement when explosion occurred on the installed military runway and taxiway by the multiple warheads weapon system. And The multiple warheads weapon systems is able to cause extensive damage but the destructive power of each warhead is not as great, so I would like to propose an airfield pavement design plan for minimal protection against such attacks.

• Journal of Korean Society of Transportation
• /
• v.29 no.3
• /
• pp.115-122
• /
• 2011

This paper investigates the accuracy of the vehicle pre-braking speed estimated based upon measured skidding distance. Driver ordinarily takes sudden braking when urgent situation is developed in the front or when the driver is involved in an unexpected situation, and the driver may be inflicted upon an accident depending on the required stopping distance. Among factors influencing the stopping distance of vehicle such as recognition response time of driver, performance of vehicle's braking device, and state of road surface etc, pre-braking speed is seemingly the most important influencing factor. Currently, in the investigating section of traffic accidents, the state of overspeed is determined by the pre-skidding speed calculated based on the length of skid mark. In order to identify the accurate cause of the accident, it is strongly recommended that estimation of pre-braking speed should be estimated taking into account speed reduction during transient time. In this study, we propose a method for estimating more accurate exact speed information of vehicle at the time of traffic accident. The outcomes from this study potentially help better understanding of the characteristics of vehicle for traffic safety in the future.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.31 no.3
• /
• pp.273-282
• /
• 2015

Centric occlusion-maximum intercuspation (CO-MI) discrepancy is one of main causes of evoking premature contact and resultant mandibular shift. These non-physiological conditions can induce temporomandibular disease, periodontitis, and non-carious cervical lesion. Therefore, if CO-MI discrepancy exists in patients who need extensive prosthetic rehabilitation, it must be corrected and then physiological occlusion must be restored. This report describes the treatment procedure of removing CO-MI discrepancy and prosthetic rehabilitation in a patient with 3.5 mm discrepancy, multiple caries and periodontitis. Proper mandibular position and modified opening & closing movement were confirmed by ARCUSdigma II and transcranial radiograph.

• The korean journal of orthodontics
• /
• v.34 no.4 s.105
• /
• pp.303-312
• /
• 2004

An unfavorable tipping movement can occur during the retraction of anterior teeth because orthodontic force is loaded by brackets positioned far from the center of resistance. To avoid this unfavorable movement, a compensating curved wire or lingual root torque wire is used. The purpose of this study is to investigate, using photoelastic material, the distribution of initial stress associated with the retraction of the incisors according to the degree of the compensating curve, to model changes associated with tooth ud alveolar bone structure. The following results were obtained by analysis of the polarizing plate of the effects of initial stress resulting from retraction of the anterior teeth: 1. When the incisors were retracted using combination archwire or sliding mechanics, the maximal polarizing pattern of the apical area decreased as the degree of the compensating owe increased from 0 to 15 to 30. 2. When the incisors were retracted by the combination archwire or sliding mechanics, the maximal polarizing pattern of the canine and premolar area increased as the degree of the compensating curve increased from 0to 15to 30. 3. A lower degree of polarizing patterns were associated with the combination archwire technique than the sliding mechanics technique at a given force. The above results indicate that there is no significant difference between the combination loop archwire technique and sliding mechanics, for the retraction of maxillary anterior teeth with decreased lingual tipping tendency by a compensating curve on the arch wire. However, the use of sliding mechanics is more effective for the prevention of lingual inclination of the anterior teeth, because the hook used in sliding mechanics is closer to the center of resistance of the maxillary anterior teeth.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.16 no.3
• /
• pp.202-210
• /
• 2013

As incomes increase, interest in ocean leisure picks up. As a result, a lot of research and developments on hull form design and production of planing boats, mostly used for ocean leisure, are needed. Analysis in researches on resistance of planing boats shows that resistance characteristic of planing boats is different from resistance characteristic of general boats because the former is fast, and its wetted surface is very small. Using Savitsky formula widely used in the calculation of effective horse power in shipbuildingyards, and propulsion system and engine manufacturers, this study calculated total resistance of a research planing boat. Then it analyzed the flow characteristics of the planing boat through theoretical analysis and wind tunnel experiment, and computed air resistance and lift force by changes of speed and trim angle. It also compared and analyzed result of theoretical analysis and experiment of the ratio of air resistance to total resistance under variations of velocity and trim angle. When the study is used to estimate more accurate effective horse power, it is expected to remedy abuses of unnecessarily installing high-powered engine. As nature disasters due to abnormal changes of weather increase, interest in greenhouse gas grows. International Maritime Organization (IMO) legislated Energy Efficiency Design Index (EEDI) and Energy Efficiency Operational Indicator (EEOI) to reduce ship greenhouse gas emissions. But this index will be applied to over 400 tons ships, small ships, emitting more greenhouse gases than larege ships per unit power, will dodge the regulations. Thus, this study indicated a problem by calculating greenhouse gas emissions of an ocean leisure planning boat (a small ship), and suggested the need for EEDI of small ships.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.40 no.1
• /
• pp.17-22
• /
• 2004

This study was carried out at the CWC of Chosun university for the purpose of resistance performance improvement of planing hull, and the results of the tests were confirmed cooperatively with WJFEL. G/T 100 ton class planing hull form was selected, and the improvement of hull form including appendages were performed by using some model test techniques. The model test scope comprises resistance relative tests including wave profile observation, trim and sinkage measurement and flow visualization tests at full load and trial conditions for one bare hull and for two appended hulls. The final wedge and spray strip combined with improved hull form showed about 1.0 knot speed improvement at both of full and trial conditions, and outstanding improvement for fore wave phenomena.

• Journal of Advanced Navigation Technology
• /
• v.22 no.5
• /
• pp.343-350
• /
• 2018

The number of international passengers at Gimhae International Airport, the fourth-largest airport in Korea, is gradually increasing. This raised the need for a new airport in southeastern region, and Ministry of Land, Infrastructure and Transport decided to build a new runway for Gimhae International Airport. In this study, to predict the noise generated by a new runway, the noise analysis using the aviation environmental design tool (AEDT) of Federal Aviation Administration (FAA) was performed. In this paper, when a new runway was built at the Gimhae International Airport, an area of noise damage that is increasing than the present was predicted using arrival and departure data of airlines in a day.

• Journal of the Society of Naval Architects of Korea
• /
• v.31 no.3
• /
• pp.100-111
• /
• 1994

This study was carried out for understanding the characteristics of the spray around high speed vessels. Prismatic planing hull made of an acrylate board was used to the tests. The distribution of local spray velocity were estimated from the analysis of the spray visualization. A new test system for measuring the spray thickness is proposed, and was used to estimate the local spray thickness in the model. The pressure distributions on the bottom of the hull are measured and integrated to estimate the pressure drag of the model in the towing tests. Finally. the spray drag/lift component is separated from the total drag/lift on the prismatic hull. These test results show that the spray drag component on high speed vessels is relatively large and important in total drag.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.23 no.5
• /
• pp.566-573
• /
• 2017

The chine of high speed vessels does not only play a role in changing position when planing but also helps balancing the hull. It also has a great influence on resistance performance. However, designing a chine requires a lot of experience because it is influenced by various factors such as displacement, transom shape, draft and width. Such a design is not based on an empirical formula, but the purpose of this study is to provide basic guidelines regarding the shape of chine through calculation. This design was developed using Yacht-one, a commercial design program, and analysis was performed using Star-CCM+, also a commercial analysis program. Analysis of the hull selected in this study was carried out by Dynamic Fluid Body Interaction (DFBI) method. Analysis of the chine was carried out at chine angles of 15, 16, 17, and 19degrees, at a speed of 30knots. The result indicated that the highest trim occurred at 16 degrees among the four chine angles considered, and the highest heave occurred at 15degree. In terms of resistance performance, minimum resistance was observed at 16 degrees. Consequently, for minimum ship resistance, it is necessary to complete calculations in accordance with the chine angles, ${\pm}2$ degrees from the initial chine angle, which should be carried out a the design stage.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2017.11a
• /
• pp.236-237
• /
• 2017

In this research, experimental seakeeping results of Warped hull form 2 on the regular waves were compared with numerical results of strip method and CFD. In case of ship's speed, there are 3 cases (3.4m/s, 4.6m/s, 5.75m/s) for numerical simulation, and they are belong to semi-planing and planing condition. Consequently, in case of strip method, it is shown that the resonance phenomena occurred from around ${\lambda}/L_{OA}=2$ to 4 and RAO value were significantly higher than that of other. this is different from experimental results. In case of CFD, overall trends were similar with experimental values except there are somewhat excessive RAO values around ${\lambda}/L_{OA}=0.5$ to 2.5. these phenomena is confirmed that it became larger as the ship's speed increased, and it was considered that the error occurred because the number of mesh in vertical direction of wave height at ${\lambda}/L_{OA}=0.5$ to 2.5 were relatively less than those of wave height at ${\lambda}/L_{OA}=2.5$ to 5.2.